Transmission Installation

Transmission Installation

Special Tools Required
^ Engine support hanger, A and Reds AAR-T-12566
^ Subframe adapter VSB02C000016*
^ Engine hanger balance bar VSB02C000019
*These special tools are available through the Acura Tool and Equipment Program 1888-424-6857

NOTE: Use fender covers to avoid damaging painted surfaces.

SRS components are located in this area. Review the SRS component locations, and the precautions and procedures before performing repair or service.

1. Make sure the 14 x 20 dowel pin (A) and 10 x 20 dowel pin (B) are installed in the clutch housing.





2. Apply super high temp urea grease (P/N 08798-9002) to the release fork (C) and the release bearing (D). Install the release fork, the release bearing, and the boot (E).
3. Place the transmission on the transmission jack, and raise it to the engine level.
4. Install the lower transmission mounting bolts.





5. Install the lower mounting bolts (A) clutch cover (B).





6. Install the front engine mount upper bracket.





7. Support the front subframe with the front subframe adapter and a jack.





8. Loosely install the front subframe (A) and front subframe stiffeners (B).





9. Align the reference line (A) that you noted when you removed the transmission with the edge (B) of both rear stiffeners (C), and tighten the rear subframe mounting bolts, the front bolts, and tighten the stiffener bolts to the specified torque.





10. Install the body mount bracket.





11. Install the lower transmission front mount (A) and the lower transmission rear mount (B).





12. Install the lower transmission mount mounting nuts.





13. Install the lower engine rear mount mounting bolts.





14. Connect the power steering pressure switch connector.





15. Install the intermediate shaft.
16. Install the left and right driveshaft inboard joints.
17. Connect the tie-rod ball joint.
18. Connect the knuckle onto the lower arm.
19. Install the damper fork.
20. Connect the front stabilizer link.
21. Install exhaust pipe A.
22. Install the splash shield.
23. Install the engine under cover.
24. Lower the vehicle on the lift.
25. Install the transmission mount bracket (A) and ground cable (B).





26. Remove the engine support hanger and engine hanger balance bar from the engine.
27. Unlock the steering wheel.
28. Connect the steering joint to the steering gearbox pinion shaft (A) by aligning the reference mark (B) you made when you disconnected the steering joint, and remove the wire (C) from the joint yoke (D).





29. Install the steering joint cover (E).
30. Install the power steering pump outlet line (A) with a new O-ring (B) to the pump (C), and install the hose (D) in its clamp (E).





31. Connect the return hose (F) to the power steering fluid reservoir (G), then secure the hose with its clamp (H).
32. Install the upper transmission mounting bolts.





33. Install the front engine mount mounting bolt (A), the front engine mount stop (B), and mounting nuts (C).





34. Apply super high temp urea grease (P/N 08798-9002) to the end of the pushrod. Install the slave cylinder. Be careful not to bend the clutch line.





35. Connect the vacuum hose (A).





36. Install the shift cable bracket (B) and shift cables (C).
37. Apply a light coat of super high temp urea grease (P/N 08798-9002) or silicone grease (P/N 08C30-B0234M) to the cable ends, then install new lock pins (D) as shown.
38. Install the harness bracket.





39. Install the starter motor and wire.
40. Connect the vacuum hose (A), then install the harness clips (B).





41. Connect the input shaft (mainshaft) speed sensor connector (A) and output shaft (countershaft) speed sensor connector (B).





42. Connect the back-up light switch connector (A) and reverse lockout solenoid connector (B), then install the harness clips (C).





43. Install the strut brace.





44. Install the under-hood fuse/relay box.





45. Refill the transmission with the recommended transmission fluid.
46. Install the battery base.





47. Install the resonator chamber and air cleaner assembly.
48. Install the battery. Clean the battery posts and cable terminals. Connect the positive cable to the battery first, then connect the negative cable, and apply multipurpose grease to prevent corrosion.
49. Install the bulkhead cover (A) and the engine cover (B).





50. Fill the power steering fluid reservoir with fluid to the upper level line.
51. Start the engine, then turn the steering wheel from lock-to-lock several times to bleed air from the system.
52. Recheck the fluid level, and refill if necessary.
53. Install the right rear engine compartment cover (A) and the right side engine compartment cover (B).





54. Install the left side engine compartment cover (A) and the left rear engine compartment cover (B).