Manufacturer Code Charts: 2601
Navigation System DTC Troubleshooting: 2601
DTC 2601: Display Diag: Connect
NOTE:
- Check the vehicle battery condition first. Testing and Inspection
- Check for B-CAN DTCs and resolve them before troubleshooting.
- Before you troubleshoot, make sure to follow the general troubleshooting information. Reading and Clearing Diagnostic Trouble Codes
1. Clear the hard error code. Reading and Clearing Diagnostic Trouble Codes
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Go into the Diagnostic Menu, and select the Self-Diagnosis Mode in the Select Diagnosis Items menu. Navigation System Diagnostic Mode
4. Check the System Links.
Is the Display icon red?
YES - Go to step 5.
NO - Intermittent failure, the system is OK at this time.
5. Check for poor connections or loose terminals at navigation unit connector B (32P), audio unit connector E (14P), and AcuraLink control unit (XM receiver) connector A (32P), or XM receiver connector A (14P).
Are the connections OK?
YES - Go to step 6.
NO - Repair poor connections or loose terminals, and recheck the self-diagnosis mode. Navigation System Diagnostic Mode
6. Turn the ignition switch to LOCK (0).
7. Disconnect navigation unit connector B (32P) and the navigation display unit 28P connector.
8. Connect the navigation unit connector B (32P) terminals No. 10 and No. 26 with a jumper wire.
9. Check for continuity between navigation display unit 28P connector terminals No. 5 and No. 19.
Is there continuity?
YES - Go to step 10.
NO - There is an open in the wire between navigation unit and the navigation display unit. Replace the affected shielded harness.
10. Disconnect the jumper wire.
11. Disconnect the audio unit connector E (14P), AcuraLink control unit (XM receiver) connector A (32P) or XM receiver connector A (14P), USB adapter unit connector A (14P), and the HandsFreeLink control unit 28P connector.
12. Check for continuity between navigation display unit 28P connector terminals No. 5 and No. 19, and terminals No. 3 and No. 17.
Is there continuity?
YES - There is a short in the wire(s). Replace the affected shielded harness.
NO - Go to step 13.
13. Check for continuity between body ground and navigation display unit 28P connector terminals No. 3, No. 5 No. 17, and No. 19 individually.
Is there continuity?
YES - There is a short to body ground in the wire(s) between the navigation display unit and the navigation unit. Replace the affected shielded harness.
NO - Go to step 14.
14. Check for continuity between the terminals of navigation display unit 28P connector according to the table.
Is there continuity?
YES - There is a short in wire(s) between the navigation display unit and the navigation unit. Replace the affected shielded harness.
NO - Go to step 15.
15. Reconnect the all connectors, then turn the ignition switch to ON (II).
16. Go into the Diagnostic Menu, and select the Self-Diagnosis Mode in the Select Diagnosis Items menu. Navigation System Diagnostic Mode
17. Check the System Links.
Is the Display icon red?
YES - Go to step 18.
NO - Intermittent failure, the system is OK at this time.
18. Turn the ignition switch to LOCK (0).
19. Disconnect AcuraLink control unit (XM receiver connector A (32P) or XM receiver connector A (14P).
20. Turn the ignition switch to ON (II).
21. Go into the Diagnostic Menu, and Select the Self-Diagnosis Mode in the Select Diagnosis Items Menu. Navigation System Diagnostic Mode
22. Check the System Links.
Is the Display icon red?
YES - Go to step 23.
NO - Replace the AcuraLink control unit (XM receiver) AcuraLink Control Unit (XM Receiver) Removal/Installation or the XM receiver. XM Receiver Removal/Installation (Without AcuraLink With XM Radio)
23. Turn the ignition switch to LOCK (0).
24. Disconnect the USB adapter unit connector A (14P).
25. Turn the ignition switch to ON (II).
26. Go into the Diagnostic Menu, and Select the Self-Diagnosis Mode in the Select Diagnosis Items Menu. Navigation System Diagnostic Mode
27. Check the System Links.
Is the Display icon red?
YES - Go to step 28.
NO - Replace the USB adapter unit. USB Adapter Unit Replacement
28. Turn the ignition switch to LOCK (0).
29. Disconnect the HandsFreeLink control unit 28P connector.
30. Turn the ignition switch to ON (II).
31. Go into the Diagnostic Menu, and Select the Self-Diagnosis Mode in the Select Diagnosis Items Menu. Navigation System Diagnostic Mode
32. Check the System Links.
Is the Display icon red?
YES - Go to step 33.
NO - Replace the HandsFreeLink control unit. Service and Repair
33. Turn the ignition switch to LOCK (0).
34. Substitute a known-good navigation display unit. Navigation Display Unit Removal/Installation
35. Turn the ignition switch to ON (II).
36. Go into the Diagnostic Menu, and Select the Self-Diagnosis Mode in the Select Diagnosis Items Menu. Navigation System Diagnostic Mode
37. Check the System Links.
Is the Display icon red?
YES - Replace the audio unit. Audio Unit Removal/Installation (With AcuraLink)
NO - Replace the original navigation display unit. Navigation Display Unit Removal/Installation