DTC B0014-B0045
DTC B0014-B0045
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
DTC Descriptors
DTC B0014 01
- Driver Seat Side Air Bag Deployment Loop Short to Battery
DTC B0014 02
- Driver Seat Side Air Bag Deployment Loop Short to Ground
DTC B0014 04
- Driver Seat Side Air Bag Deployment Loop Open
DTC B0014 0D
- Driver Seat Side Air Bag Deployment Loop High Resistance
DTC B0014 0E
- Driver Seat Side Air Bag Deployment Loop Low Resistance
DTC B0015 01
- Driver Seat Belt Retractor Pretensioner Deployment Loop Short to Battery
DTC B0015 02
- Driver Seat Belt Retractor Pretensioner Deployment Loop Short to Ground
DTC B0015 04
- Driver Seat Belt Retractor Pretensioner Deployment Loop Open
DTC B0015 0D
- Driver Seat Belt Retractor Pretensioner Deployment Loop High Resistance
DTC B0015 0E
- Driver Seat Belt Retractor Pretensioner Deployment Loop Low Resistance
DTC B0016 01
- Left Roof Rail Air Bag Deployment Loop 1 Short to Battery
DTC B0016 02
- Left Roof Rail Air Bag Deployment Loop 1 Short to Ground
DTC B0016 04
- Left Roof Rail Air Bag Deployment Loop 1 Open
DTC B0016 0D
- Left Roof Rail Air Bag Deployment Loop 1 High Resistance
DTC B0016 0E
- Left Roof Rail Air Bag Deployment Loop 1 Low Resistance
DTC B0017 01
- Driver Knee Air Bag Deployment Loop Short to Battery
DTC B0017 02
- Driver Knee Air Bag Deployment Loop Short to Ground
DTC B0017 04
- Driver Knee Air Bag Deployment Loop Open
DTC B0017 0D
- Driver Knee Air Bag Deployment Loop High Resistance
DTC B0017 0E
- Driver Knee Air Bag Deployment Loop Low Resistance
DTC B0019 01
- Passenger Instrument Panel Air Bag Deployment Loop Stage 1 Short to Battery
DTC B0019 02
- Passenger Instrument Panel Air Bag Deployment Loop Stage 1 Short to Ground
DTC B0019 04
- Passenger Instrument Panel Air Bag Deployment Loop Stage 1 Open
DTC B0019 0D
- Passenger Instrument Panel Air Bag Deployment Loop Stage 1 High Resistance
DTC B0019 0E
- Passenger Instrument Panel Air Bag Deployment Loop Stage 1 Low Resistance
DTC B001A 01
- Driver Seat Belt Anchor Pretensioner Deployment Loop Short to Battery
DTC B001A 02
- Driver Seat Belt Anchor Pretensioner Deployment Loop Short to Ground
DTC B001A 04
- Driver Seat Belt Anchor Pretensioner Deployment Loop Open
DTC B001A 0D
- Driver Seat Belt Anchor Pretensioner Deployment Loop High Resistance
DTC B001A 0E
- Driver Seat Belt Anchor Pretensioner Deployment Loop Low Resistance
DTC B001B 01
- Passenger Seat Belt Anchor Pretensioner Deployment Loop Short to Battery
DTC B001B 02
- Passenger Seat Belt Anchor Pretensioner Deployment Loop Short to Ground
DTC B001B 04
- Passenger Seat Belt Anchor Pretensioner Deployment Loop Open
DTC B001B 0D
- Passenger Seat Belt Anchor Pretensioner Deployment Loop High Resistance
DTC B001B 0E
- Passenger Seat Belt Anchor Pretensioner Deployment Loop Low Resistance
DTC B0020 01
- Passenger Instrument Panel Air Bag Deployment Loop Stage 2 Short to Battery
DTC B0020 02
- Passenger Instrument Panel Air Bag Deployment Loop Stage 2 Short to Ground
DTC B0020 04
- Passenger Instrument Panel Air Bag Deployment Loop Stage 2 Open
DTC B0020 0D
- Passenger Instrument Panel Air Bag Deployment Loop Stage 2 High Resistance
DTC B0020 0E
- Passenger Instrument Panel Air Bag Deployment Loop Stage 2 Low Resistance
DTC B0021 01
- Passenger Seat Side Air Bag Deployment Loop Short to Battery
DTC B0021 02
- Passenger Seat Side Air Bag Deployment Loop Short to Ground
DTC B0021 04
- Passenger Seat Side Air Bag Deployment Loop Open
DTC B0021 0D
- Passenger Seat Side Air Bag Deployment Loop High Resistance
DTC B0021 0E
- Passenger Seat Side Air Bag Deployment Loop Low Resistance
DTC B0022 01
- Passenger Seat Belt Retractor Pretensioner Deployment Loop Short to Battery
DTC B0022 02
- Passenger Seat Belt Retractor Pretensioner Deployment Loop Short to Ground
DTC B0022 04
- Passenger Seat Belt Retractor Pretensioner Deployment Loop Open Circuit
DTC B0022 0D
- Passenger Seat Belt Retractor Pretensioner Deployment Loop High Resistance
DTC B0022 0E
- Passenger Seat Belt Retractor Pretensioner Deployment Loop Low Resistance
DTC B0023 01
- Right Roof Rail Air Bag Deployment Loop 1 Short to Battery
DTC B0023 02
- Right Roof Rail Air Bag Deployment Loop 1 Short to Ground
DTC B0023 04
- Right Roof Rail Air Bag Deployment Loop 1 Open
DTC B0023 0D
- Right Roof Rail Air Bag Deployment Loop 1 High Resistance
DTC B0023 0E
- Right Roof Rail Air Bag Deployment Loop 1 Low Resistance
DTC B0024 01
- Passenger Knee Air Bag Deployment Loop Short to Battery
DTC B0024 02
- Passenger Knee Air Bag Deployment Loop Short to Ground
DTC B0024 04
- Passenger Knee Air Bag Deployment Loop Open
DTC B0024 0D
- Passenger Knee Air Bag Deployment Loop High Resistance
DTC B0024 0E
- Passenger Knee Air Bag Deployment Loop Low Resistance
Diagnostic Fault Information
Circuit/System Description
During a side or frontal crash of sufficient force the inflatable restraint sensing and diagnostic module (SDM) will allow current to flow through the deployment loop in order to deploy an air bag. There are 2 shorting bars used within the module connector which will short together control circuits, when the connector is disconnected. This will help to prevent unwanted deployment of the air bag or pretensioner during servicing.
Conditions for Running the DTC
Ignition voltage is between 9-16 V.
Conditions for Setting the DTC
B0014 01, B0015 01, B0016 01, B0017 01, B0019 01, B001A 01, B001B 01, B0020 01, B0021 01, B0022 01, B0023 01, B0024 01
The air bag or pretensioner control circuit is shorted to voltage for 2 seconds.
B0014 02, B0015 02, B0016 02, B0017 02, B0019 02, B001A 02, B001B 02, B0020 02, B0021 02, B0022 02, B0023 02, B0024 02
The air bag or pretensioner control circuit is shorted to ground for 2 seconds.
B0014 04, B0015 04, B0016 04, B0017 04, B0019 04, B001A 04, B001B 04, B0020 04, B0021 04, B0022 04, B0023 04, B0024 04
The air bag or pretensioner control circuit is open for 2 seconds.
B0014 0D, B0015 0D, B0016 0D, B0017 0D, B0019 0D, B001A 0D, B001B 0D, B0020 0D, B0021 0D, B0022 0D, B0023 0D, B0024 0D
The air bag or pretensioner deployment loop resistance is greater than 4.2 ohm for 2 seconds.
B0014 0E, B0015 0E, B0016 0E, B0017 0E, B0019 0E, B001A 0E, B001B 0E, B0020 0E, B0021 0E, B0022 0E, B0023 0E, B0024 0E
The air bag or pretensioner deployment loop resistance is less than 1.4 ohm for 2 seconds.
Action Taken When the DTC Sets
* The SDM requests the instrument cluster to illuminate the AIR BAG indicator.
* The SDM will store a DTC, however if an event occurs the system will still attempt deployments.
Conditions for Clearing the DTC
* The condition for setting the DTC no longer exists.
* A history DTC will clear once 100 malfunction-free ignition cycles have occurred.
Diagnostic Aid
Note: The following diagnostic aids apply for both current and history DTCs.
An incorrectly installed CPA or incorrectly seated connector can cause a shorting bar to short both control circuits together. Check the connectors and CPAs if a DTC with symptom byte 02 or 0E is set, to ensure the shorting bars are not causing the circuits to be shorted together. Shorting bars are used in the locations listed below:
* Passenger instrument panel air bag
* Driver and passenger seat side air bags
* Left and right roof rail air bags
* Driver and passenger knee air bags
* Driver and passenger anchor pretensioners
* Driver and passenger retractor pretensioners
* Inline connectors - on the side of the harness connector
* Harness side of the SDM connector
Terminal fretting or incorrectly seated connector can cause an open/high resistance condition. Check the circuit terminals for fretting or incorrectly seated connector if a DTC with symptom byte 04 or 0D is set. If DTCs of deployment loops which are in the seat DTC B0014 and B0021, can occur because of stress or damage to the harness due to seat movement. Move the seat to the full extend of travel while using the scan tool to observe deployment type loop parameters.
If the retractor pretensioner, passenger instrument panel or side seat air bag has inflated under unexpected conditions and/or DTC with symptom byte 01 is set, check both control circuits for a short to voltage.
Reference Information
Schematic Reference
SIR Schematics [1][2]Air Bag Systems
Connector End View Reference
Component Connector End Views Hybrid/EV Battery Pack X1 A4
Description and Operation
SIR System Description and Operation SIR System
Electrical Information Reference
* Circuit Testing Circuit Testing
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
* Connector Repairs Connector Repairs
Scan Tool Reference
Control Module References Control Module References for scan tool information
Circuit/System Verification
Note:
* Refer to SIR Service Precautions Technician Safety Information.
* Inspect all terminals for damage or corrosion when disconnecting connectors. Damage or corrosion in the following requires repair or replacement of the affected component/connector.
- Seat belt retractor pretensioner
- Seat belt anchor pretensioner
- Passenger instrument panel air bag
- Seat side air bag
- Roof rail air bag
- Knee air bag
- SDM
- SDM wiring harness connector
* The connector and connector position assurance (CPA) may seat independent of each other. Both the connector and CPA should seat with an audible and/or tactile click. The CPA isolates the shorting-bars within the connector allowing the deployment circuit to operate properly.
* If the condition is intermittent or cannot be duplicated, disconnect the connectors and add Nyogel lubricant 760G. This procedure will correct the high resistance condition due to terminal fretting corrosion.
Observe the scan tool Deployment Loop Resistance parameters while moving the harness near each connector listed below. The reading should stay consistently between 1.7 and 4.2 ohm without any drop outs or spikes.
* F105 Passenger instrument panel
* F105 Roof rail air bag
* F106 Seat side air bag
* F112 Seat belt retractor pretensioner
* F113 Seat belt anchor pretensioner
* F114 Knee air bag
* Any inline harness
* K36 SDM
1. Verify the scan tool Deployment Loop Resistance 1 and 2 parameters stay consistently between 2.1 and 4.0 ohm without any spikes or dropouts while moving the harness near each connector.
• If less than 2.1 or greater than 4.0 ohm
• Refer to Circuit/System Testing.
• If there are spikes or dropouts
• Replace the air bag or pretensioner.
• If within 2.1 and 4.0 ohm without any spikes or dropouts
2. DTC B0014-B0045 should only be set as a history DTC.
• If the DTC is set as current
• Refer to Circuit/System Testing.
• If the DTC is set as history
3. Verify the scan tool Deployment Loop Resistance 1 and 2 parameters stay consistently between 2.1 and 4.0 ohm without any drop outs or spikes while moving the harness near each connector listed below.
* F105 Passenger instrument panel air bag
* F105 Roof rail air bag
* F106 Seat side air bag
* F112 Seat belt retractor pretensioner
* F113 Seat belt anchor pretensioner
* F114 Knee air bag
* Any inline harness
* K36 SDM
• If the reading is erratic while moving the harness, perform the following
* Inspect each connector terminal for damage or corrosion and repair as necessary.
* Apply Nyogel lubricant 760G to each connector terminal.
* Insure each connector and CPA is correctly seated.
• If within 2.1 and 4.0 ohm without any spikes or dropouts
4. All OK
Circuit/System Testing
DTC B0014-B0018 or B0021-B0045
1. Ignition OFF.
2. Disconnect the scan tool.
3. Disconnect the harness connector listed below:
* F114 Knee air bag
* F105 Roof rail air bag
* F106 Seat side air bag
* F112 Seat belt retractor pretensioner
* F113 Seat belt anchor pretensioner
4. Wait for 120 seconds.
5. Test for greater than 25 ohm between the control circuit terminals listed below:
* F114 Driver knee air bag terminal 1 and 2
* F114 Passenger knee air bag terminal 1 and 2
* F105 Left roof rail air bag terminal 1 and 2
* F105 Right roof rail air bag terminal 1 and 2
* F106 Driver seat side air bag terminal 1 and 2
* F106 Passenger seat side air bag terminal 1 and 2
* F113 Driver seat belt anchor pretensioner terminal 1 and 2
* F113 Passenger seat belt anchor pretensioner terminal 1 and 2
* F112 Driver seat belt retractor pretensioner terminal 1 and 2
* F112 Passenger seat belt retractor pretensioner terminal 1 and 2
• If 25 ohm or less
1. Disconnect the harness connector at the K36 SDM.
2. Test for infinite resistance between the two control circuits.
• If less than infinite resistance, repair the short between the two circuits.
• If infinite resistance, replace the K36 SDM.
• If greater than 25 ohm
6. Ignition ON.
7. Test for less than 11 V between the control circuit terminals listed below and ground:
* F114 knee air bag control circuit terminal 1
* F114 knee air bag control circuit terminal 2
* F105 roof rail air bag control circuit terminal 1
* F105 roof rail air bag control circuit terminal 2
* F106 seat side air bag control circuit terminal 1
* F106 seat side air bag control circuit terminal 2
* F113 Driver seat belt anchor pretensioner terminal 1 and 2
* F113 Passenger seat belt anchor pretensioner terminal 1 and 2
* F112 seat belt retractor pretensioner control circuit terminal 1
* F112 seat belt retractor pretensioner control circuit terminal 2
• If 11 V or greater
1. Ignition OFF.
2. Disconnect the harness connector at the K36 SDM.
3. Ignition ON.
4. Test for less than 1 V between the control circuit and ground.
• If 1 V or greater, repair the short to voltage on the circuit.
• If less than 1 V, replace the K36 SDM.
• If less than 11 V
8. Ignition OFF.
9. Test for greater than 25 ohm between the control circuit terminals listed below and ground:
* F114 knee air bag control circuit terminal 1
* F114 knee air bag control circuit terminal 2
* F105 roof rail air bag control circuit terminal 1
* F105 roof rail air bag control circuit terminal 2
* F106 seat side air bag control circuit terminal 1
* F106 seat side air bag control circuit terminal 2
* F113 Driver seat belt anchor pretensioner terminal 1 and 2
* F113 Passenger seat belt anchor pretensioner terminal 1 and 2
* F112 seat belt retractor pretensioner control circuit terminal 1
* F112 seat belt retractor pretensioner control circuit terminal 2
• If 25 ohm or less
1. Disconnect the harness connector at the K36 SDM.
2. Test for infinite resistance between the control circuit and ground.
• If less than infinite resistance, repair the short to ground on the circuit.
• If infinite resistance, replace the K36 SDM.
• If greater than 25 ohm
10. Ignition OFF.
11. Install a 3 A fused jumper wire between the control circuit terminals listed below:
* F114 Driver knee air bag terminal 1 and 2
* F114 Passenger knee air bag terminal 1 and 2
* F105 Left roof rail air bag terminal 1 and 2
* F105 Right roof rail air bag terminal 1 and 2
* F106 Driver seat side air bag terminal 1 and 2
* F106 Passenger seat side air bag terminal 1 and 2
* F113 Driver seat belt anchor pretensioner terminal 1 and 2
* F113 Passenger seat belt anchor pretensioner terminal 1 and 2
* F112 Driver seat belt retractor pretensioner terminal 1 and 2
* F112 Passenger seat belt retractor pretensioner terminal 1 and 2
12. Ignition ON.
13. Verify the scan tool Deployment Loop Resistance parameter is less than 2 ohm.
• If 2 ohm or greater
1. Ignition OFF.
2. Disconnect the harness connector at the K36 SDM.
3. Test for less than 2 ohm in each control circuit end to end.
• If 2 ohm or greater, repair the open/high resistance in the circuit.
• If less than 2 ohm, replace the K36 SDM.
• If less than 2 ohm
14. Replace the F114 knee air bag, F105 roof rail air bag, F106 seat side air bag or F112 seat belt retractor pretensioner.
DTC B0019-B0020
1. Ignition OFF.
2. Disconnect the scan tool.
3. Disconnect the F105 passenger instrument panel air bag harness connector.
4. Test for greater than 25 ohm between the appropriate control circuit terminals listed below on the SDM side of the connector:
* F105 Passenger instrument panel airbag stage 1 terminal 1 and 2 X1
* F105 Passenger instrument panel airbag stage 2 terminal 4 and 5 X1
• If 25 ohm or less
1. Disconnect the harness connector at the K36 SDM.
2. Test for infinite resistance between the two control circuits.
• If less than infinite resistance, repair the short between the two circuits.
• If infinite resistance, replace the K36 SDM.
• If greater than 25 ohm
5. Ignition ON.
6. Test for less than 11 V between the control circuit terminals listed below and ground:
* Passenger instrument panel air bag stage 1 control circuit terminal 1 X1
* Passenger instrument panel air bag stage 1 control circuit terminal 2 X1
* Passenger instrument panel air bag stage 2 control circuit terminal 4 X1
* Passenger instrument panel air bag stage 2 control circuit terminal 5 X1
• If 11 V or greater
1. Ignition OFF.
2. Disconnect the harness connector at the K36 SDM.
3. Ignition ON.
4. Test for less than 1 V between the control circuit and ground.
• If 1 V or greater, repair the short to voltage on the circuit.
• If less than 1 V, replace the K36 SDM.
• If less than 11 V
7. Test for greater than 25 ohm between the control circuit terminals listed below and ground:
* Passenger instrument panel air bag stage 1 control circuit terminal 1 X1
* Passenger instrument panel air bag stage 1 control circuit terminal 2 X1
* Passenger instrument panel air bag stage 2 control circuit terminal 4 X1
* Passenger instrument panel air bag stage 2 control circuit terminal 5 X1
• If 25 ohm or less
1. Disconnect the harness connector at the K36 SDM.
2. Test for infinite resistance between the control circuit and ground.
• If less than infinite resistance, repair the short to ground on the circuit.
• If infinite resistance, replace the K36 SDM.
• If greater than 25 ohm
8. Ignition OFF.
9. Iinstall a 3 A fused jumper wire between the control circuit terminals listed below:
* F105 Passenger instrument panel airbag stage 1 terminal 1 and 2 X1
* F105 Passenger instrument panel airbag stage 2 terminal 4 and 5 X1
10. Ignition ON.
11. Verify the scan tool Deployment Loop Resistance parameter is less than 2 ohm.
• If 2 ohm or greater
1. Ignition OFF.
2. Disconnect the harness connector at the K36 SDM.
3. Test for less than 2 ohm in each control circuit end to end.
• If 2 ohm or greater, repair the open/high resistance in the circuit.
• If less than 2 ohm, replace the K36 SDM.
• If less than 2 ohm
12. Replace the F105 passenger instrument panel air bag.
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the diagnostic procedure.
* Driver or Passenger Seat Side Inflatable Restraint Module Replacement Driver or Passenger Seat Side Inflatable Restraint Module Replacement
* Front Seat Belt Anchor Plate Tensioner Replacement Front Seat Belt Anchor Plate Tensioner Replacement
* Driver or Passenger Seat Retractor Side Belt Replacement Driver or Passenger Seat Retractor Side Belt Replacement
* Inflatable Restraint Instrument Panel Lower Module Replacement - Driver Side Inflatable Restraint Instrument Panel Lower Module Replacement - Driver Side
* Inflatable Restraint Instrument Panel Lower Module Replacement - Passenger Side Inflatable Restraint Instrument Panel Lower Module Replacement - Passenger Side
* Instrument Panel Inflatable Restraint Module Replacement Instrument Panel Inflatable Restraint Module Replacement
* Roof Side Rail Inflatable Restraint Module Replacement Roof Side Rail Inflatable Restraint Module Replacement
* SIR/SRS Wiring Repairs SIR/SRS Wiring Repairs
* Control Module References Control Module References for SDM replacement, setup, and programming