Fuel Pressure Relief Procedure
TOOLS REQUIREDJ 42435 CNG Tank Vent Kit
1. Using a scan tool communicate with the Alternative Fuels ECM.
If communication cannot be established and the Diagnostic System Check - Alternative Fuels (Computers and Controls Systems) has already been performed proceed to Step 7.
2. Store the DTC Information for any Alternative Fuels ECM DTCs that may be set.
3. Clear all Alternative Fuels ECM DTC Information and then turn the ignition OFF.
4. Start and idle the engine.
Ensure that the engine is operating on CNG by observing that the fuel indicator lamp (FIL) is OFF and that both the AFO Signal and the AFO Signal Command scan tool displays (Engine Data-Alt. Fuels) indicate the AFECM is in command of engine fueling.
If the engine fails to operate on CNG or start at all, proceed to Step 7.
5. Using the scan tool, select the high pressure lock-off relay special function.
6. While the engine is operating on CNG command the lock-off relay OFF and observe the fuel tank pressure sensor data parameter.
If the fuel pressure fails to decrease proceed to Step 7.
When the engine stalls or a switch-over to gasoline is observed, perform the following:
6.1. Turn the ignition OFF.
6.2. Remove the CNG 20-amp fuse in order to prevent a CNG prime pulse from occurring during service.
6.3. A small amount of CNG will remain in the fuel lines and components. Slowly open the fittings in order to release any remaining pressure when disconnecting a fuel line.
6.4. Fuel Pressure Relief for the CNG system is now complete. Proceed to Step 12.
7. Close the manual lock-down screws located on both of the high pressure lock-off solenoid manual shut-off fittings by rotating the allen screws clockwise until fully seated. Holes are provided in the side of the fuel tank frame in order to allow access to the manual shut-off fittings.
CAUTION: Refer to Battery Disconnect Caution in Service Precautions.
8. Turn the ignition OFF and disconnect the negative battery cable.
CAUTION: When relieving the Compressed Natural Gas (CNG) fuel system pressure, take the following precautions in order to prevent fire and personal injury:
^ Vent the CNG fuel system in a well ventilated work area.
^ Keep sparks, flames, and smoking material away from the area.
^ Wear the appropriate hearing protection during the venting procedure. A sudden pressure loss from an uncontrolled gas leak can cause hearing damage.
9. Slowly loosen the fuel line fitting at the high pressure regulator (HPR) INLET port (1) several turns. Do NOT remove the fitting.
10. If fuel is not venting with the HPR inlet fitting loosened, relieve fuel line tension by pulling the line away from the HPR.
11. After fuel has stopped venting at the HPR fitting perform the following:
11.1. Slowly loosen the fuel line fitting (6) at the low pressure lock-off (LPL) INLET port (5) several turns. Do NOT remove the fitting.
11.2. Relieve fuel line tension by pulling the line away from the LPL.
11.3. Fuel Pressure Relief for the CNG system is complete when the fuel line (6) at the LPL inlet port (5) can be pulled away from the O-ring face seal and fuel fails to vent.
CAUTION: Refer to Compressed Natural Gas (CNG) O-Ring Caution in Service Precautions.
11.4. Replace the O-ring face seals at all fittings that were disconnected or loosened.
11.5. After all necessary repairs are complete perform the following:
11.5.1. Tighten any loosened fittings to the correct torque. Refer to Fastener Tightening Specifications.
11.5.2. Open the manual lock-down screws located on the HPL manual shut-off fittings by rotating the allen screws counterclockwise until fully seated on any vehicle that does not require venting of the CNG fuel TANKS.
Leave the manual lock-down screws CLOSED on any vehicle that will require CNG fuel TANK venting.
IMPORTANT: If the service necessary for the vehicle requires that the ignition be turned ON with CNG components or lines disconnected, keep the CNG 20 amp fuse removed in order to prevent CNG fuel venting during an ignition ON prime pulse.
12. If the service necessary for the vehicle requires the CNG fuel TANK be relieved of all internal pressure, refer to Fuel Tank Venting Procedure.