C0297
DTC C0297
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
DTC Descriptor
DTC C0297 00
-
Brake Applied Output Circuit
Diagnostic Fault Information
Circuit/System Description
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The brake pedal position sensor provides an analog voltage signal that will increase as the brake pedal is applied. The body control module (BCM) provides a low reference signal and a 5 V reference voltage to the brake pedal position sensor. When the variable signal reaches a voltage threshold indicating the brakes have been applied, the BCM will apply battery voltage to the stop lamp control circuit illuminating the left and right stop lamps and the center high mounted stop lamp (CHMSL). The BCM also applies battery voltage to the transmission control module (TCM) and engine control module (ECM) via the brake applied signal circuit.
Conditions for Running the DTC
* Battery voltage must be between 9-16 V.
* Brakes APPLIED.
Conditions for Setting the DTC
The BCM detects a short to ground in the brake applied signal circuit.
Actions Taken When the DTC Sets
The Service Vehicle Soon indicator is commanded ON.
Conditions for Clearing the DTC
* The condition responsible for setting the DTC no longer exists.
* A history DTC will clear once 100 malfunction-free ignition cycles have occurred.
Reference Information
Schematic Reference
Exterior Lights Schematics Exterior Lights Schematics
Connector End View Reference
Component Connector End Views 1-2 Shift Solenoid (SS) Valve (MN5)
Description and Operation
Exterior Lighting Systems Description and Operation Exterior Lighting Systems
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
Scan Tool Reference
Control Module References Programming and Relearning for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the X1 harness connector at the ECM.
2. Disconnect the harness connector at the TCM.
3. Connect a test lamp between the signal circuit terminal 57 at the ECM harness connector and ground.
4. Ignition ON, command the stop lamps ON and OFF by applying and releasing the brake pedal. The test lamp should turn ON and OFF when changing between the commanded states.
• If the test lamp is always ON, test the signal circuit for a short to voltage. If the circuit tests normal, replace the BCM.
• If the test lamp is always OFF, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.
5. Ignition OFF, connect a test lamp between the signal circuit terminal 57 at the ECM harness connector and the connector terminal at the ECM.
6. Ignition ON, command the stop lamps ON and OFF by applying and releasing the brake pedal. The test lamp should turn ON and OFF when changing between the commanded states.
• If the test lamp does not turn ON and OFF when commanded, replace the ECM.
7. Ignition OFF, connect a test lamp between the signal circuit terminal 10 at the TCM harness connector and ground.
8. Ignition ON, command the stop lamps ON and OFF by applying and releasing the brake pedal. The test lamp should turn ON and OFF when changing between the commanded states.
• If the test lamp is always ON, test the signal circuit for a short to voltage. If the circuit tests normal, replace the BCM.
• If the test lamp is always OFF, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.
9. If all circuits test normal, replace the TCM.
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the diagnostic procedure.
* Brake Pedal Position Sensor Calibration
* Control Module References Programming and Relearning for BCM, ECM, or TCM replacement, setup, and programming