Pinpoint Test D: TR (Transmission Range) Sensor
Pinpoint Tests - OSC Equipped Vehicle
PINPOINT TEST D : TR (Transmission Range) SENSOR
NOTE: Refer to the transmission connector illustrations and solenoid body leadframe internal wiring diagram Transaxle Connector Layouts .
NOTE: TR (Transmission Range) codes may be a result of a bad common power and ground shared between the TR (Transmission Range) sensor, OSS (Output Shaft Speed) sensor and TSS (Turbine Shaft Speed) sensor.
D1 VERIFY DTCs
- Ignition OFF.
- Select PARK.
- Start the engine.
- Carry out the OBD (On-Board Diagnostic) Test. DTCs P0706, P0707 and P0708 cannot be set by an incorrectly adjusted selector lever cable.
Are only TR (Transmission Range) DTC codes present?
Yes
GO to D3.
No
GO to D2.
D2 VERIFY SELECTOR LEVER CABLE/LINKAGE ADJUSTMENT
- Verify that the selector lever cable/linkage is correctly adjusted.
Is the selector lever cable/linkage correctly adjusted?
Yes
GO to D3.
No
ADJUST the selector lever cable/linkage. REFER to Automatic Transmission/Transaxle. GO to D4.
D3 CHECK THE ELECTRICAL SIGNAL OPERATION
- Select PARK.
- Disconnect: TCM (Transmission Control Module) C1750.
- Disconnect: C1520A.
- Use a mirror to inspect both ends of the connectors for damaged or pushed-out terminals, corrosion, loose wires and missing or damaged seals.
Is there damage to the connectors, terminals or harness?
Yes
REPAIR as required. CLEAR the DTCs and RERUN OBD (On-Board Diagnostic) tests.
No
GO to D4.
D4 CHECK THE TRANSMISSION VEHICLE HARNESS FOR AN OPEN
- Disconnect: TCM (Transmission Control Module) C1750.
- Disconnect: C1520A.
- Measure the resistance for the TR (Transmission Range) sensor circuits between C1520A and the TCM (Transmission Control Module) C1750 using the following chart.
Transmission Range Sensor Circuit Connector Connector TR (Transmission Range) Ground RET24 (BN/BU) C1520A-20 TCM (Transmission Control Module) C1750-49 TR (Transmission Range) Signal VET32 (VT) C1520A-17 TCM (Transmission Control Module) C1750-45 TR (Transmission Range) Power LE111 (VT/GN) C1520A-18 TCM (Transmission Control Module) C1750-20
Is the resistance less than 5 ohms?
Yes
GO to D5.
No
REPAIR the circuit. CONNECT all components. TEST the system for normal operation.
D5 CHECK THE TRANSMISSION VEHICLE HARNESS FOR A SHORT TO GROUND
- Disconnect: C1520B.
- Measure the resistance for the TR (Transmission Range) sensor circuits between C1520A and ground using the following chart.
Transmission Range Sensor Circuit Connector Ground TR (Transmission Range) Ground RET24 (BN/BU) C1520A-20 Ground TR (Transmission Range) Signal VET32 (VT) C1520A-17 Ground TR (Transmission Range) Power LE111 (VT/GN) C1520A-18 Ground
Are all resistances greater than 10,000 ohms?
Yes
GO to D6.
No
REPAIR the circuit(s). RECONNECT all components. TEST the system for normal operation.
D6 CHECK THE TRANSMISSION VEHICLE HARNESS FOR A SHORT TO VOLTAGE
- Measure the voltage for the TR (Transmission Range) sensor circuits C1520A and ground using the following chart.
Transmission Range Sensor Circuit Connector Ground TR (Transmission Range) Ground RET24 (BN/BU) C1520A-20 Ground TR (Transmission Range) Signal VET32 (VT) C1520A-17 Ground TR (Transmission Range) Power LE111 (VT/GN) C1520A-18 Ground
Is any voltage present?
Yes
REPAIR the circuit(s). RECONNECT all components. TEST the system for normal operation.
No
GO to D7.
D7 CHECK FOR A SHORT BETWEEN TR (Transmission Range) CIRCUITS
- Measure the resistance between TR (Transmission Range) sensor circuits at the C1520A using the following chart.
Connector TR Sensor Circuit Connector C1520A-20 TR (Transmission Range) Ground RET24 (BN/BU) C1520A-17 and C1520A-18C1520A-17 TR (Transmission Range) Signal VET32 (VT) C1520A-18 and C1520A-20C1520A-18 TR (Transmission Range) Power LE111 (VT/GN) C1520A-17 and C1520A-20
Are all resistances greater than 10,000 ohms?
Yes
GO to D8.
No
REPAIR the circuits. RECONNECT all components. TEST the system for normal operation.
D8 CHECK FOR AN INTERNAL SOLENOID BODY OPEN FOR THE TR (Transmission Range) SENSOR CIRCUITS
- Remove the main control cover. Refer to Main Control Cover .
- Disconnect: TR (Transmission Range) Sensor Connector.
- Use a mirror to inspect both ends of the connector for damage or pushed-out terminals, corrosion, loose wires and missing or damaged seals.
- Measure the resistance of the TR (Transmission Range) sensor circuits between the solenoid body leadframe main connector, component side and the TR (Transmission Range) sensor connector, leadframe side.
Solenoid Body Leadframe Main Connector Pin Number TR Sensor Pin Number Circuit Function (Wire Color) 18 1 TR (Transmission Range) power (RD) 17 2 TR (Transmission Range) signal (WH) 20 3 TR (Transmission Range) ground (BK)
Is the resistance less than 5 ohms?
Yes
GO to D9.
No
INSTALL a new solenoid body leadframe. REFER to Solenoid Body Leadframe . RECONNECT all components. TEST the system for normal operation.
D9 CHECK FOR VOLTAGE AND GROUND AT THE TR (Transmission Range) SENSOR CONNECTOR
- Connect: TCM (Transmission Control Module) C1750.
- Connect: C1520A.
- Ignition ON.
- Measure the voltage on the solenoid body leadframe between TR (Transmission Range) sensor connector pins 1 (RD) and 3 (BK) solenoid body leadframe side.
Is the voltage greater than 10 volts?
Yes
INSTALL a new TR (Transmission Range) sensor. REFER to Digital Transmission Range (TR) Sensor . TEST the system for normal operation. If the condition is still present, INSTALL a new TCM (Transmission Control Module). REFER to Transmission Control Module (TCM) .
No
INSTALL a new TCM (Transmission Control Module). REFER to Transmission Control Module (TCM) . TEST the system for normal operation.