Transmission Housing Disassemble & Service
Transmission HousingHousing and Shaft Assembly Removal
Special Tools Required
Housing puller 07HAC-PK40102
1. Remove the dipstick (A).
2. Remove the shift solenoid valve cover (B), dowel pins (C), and gasket (D).
3. Disconnect the connectors from the shift solenoid valves, and remove the shift solenoid harness (E).
4. Remove the transmission housing mounting bolts (F) (16).
5. Remove the transmission housing mounting bolts (G) (3) from the torque converter housing side.
6. Align the spring pin (A) on the selector control shaft (B) with the transmission housing groove (C) by turning the selector control shaft with the detent plate.
NOTE: Do not squeeze the end of the selector control shaft tips together when turning the control shaft.
7. Install the housing puller over the mainshaft, then remove the transmission housing.
NOTE: If the top arm of your housing puller is too short, replace it with housing puller arm, 205 mm 07SAC-P0Z0101.
8. Remove the countershaft reverse gear and the needle bearing.
9. Remove the lock bolt securing the shift fork, then remove the shift fork with the reverse selector together.
10. Remove the mainshaft subassembly (A), the countershaft subassembly (B), and the secondary shaft subassembly (C) together.
If the reverse selector hub is removed by hand, remove the 4th-5th gear and needle bearings, and remove the mainshaft subassembly. Then the countershaft subassembly and the secondary shaft subassembly together.
11. Remove the bolts securing the baffle plate, then remove the baffle plate.
12. Remove the differential assembly.
Bearing Removal
Special Tools Required
^ Driver attachment, 72 x 75 mm 07746-0010600
^ Driver attachment, 78 x 80 mm 07NAD-PX40100
^ Driver attachment, 62 x 68 mm 07746-0010500
^ Driver 07749-0010000
1. Remove the snap ring (A), the cotter retainer (B), and the cotters (C) from the idler gear shaft (D), then remove the idler gear shaft. Do not distort the snap ring.
NOTE: If you are not removing the idler gear shaft bearing, idler gear shaft removal is not needed.
2. To remove the mainshaft bearing (A), the countershaft bearing (B), the secondary shaft bearing (C), and the idler gear shaft bearing (D) from the transmission housing, expand each snap ring with the snap ring pliers, then push the bearing out.
NOTE: Do not remove the snap ring unless it's necessary to clean the grooves in the housing.
Bearing Installation
Special Tools Required
^ Driver attachment, 72 x 75 mm 07746-0010600
^ Driver attachment, 78 x 80 mm 07NAD-PX40100
^ Driver attachment, 62 x 68 mm 07746-0010500
^ Driver 07749-0010000
1. Install the mainshaft bearing (A), the countershaft bearing (B), the secondary shaft bearing (C), and the idler gear shaft bearing (D) in the transmission housing in the direction shown.
2. Expand each snap ring with the snap ring pliers, and install the bearing part-way into the housing.
3. Release the pliers, then push the bearing down into the housing until the snap ring snaps in place around it.
4. After installing the bearings verify that the snap rings (A) are seated in the bearing and housing grooves, and that the ring end gaps (B) are 0 - 7 mm (0 - 0.28 in.)
5. Install the idler gear shaft (A) in the idler gear shaft bearing.
6. Install the cotters (B) and the cotter retainer (C), and secure the idler gear shaft with the snap ring (D).
Reverse Idler Gear Removal
1. Remove the bolts (A) securing the reverse idler gear shaft holder (B).
2. Install a 5 x 0.8 mm bolt (C) in the reverse gear shaft, and pull it to remove the reverse idler gear shaft (D) and the gear shaft holder together.
3. Remove the reverse idler gear.
Reverse Idler Gear Installation
1. Lightly coat the reverse idler gear shaft (A), the needle bearing (B), and the new O-rings (C) with lithium grease.
2. Assemble the new O-rings and the needle bearing on the reverse idler gear shaft, then install the reverse idler gear shaft in the reverse idler gear shaft holder (E). Align the D-shaped cut out of the shaft with the D-shaped area of the holder.
3. Install the reverse idler gear in the transmission housing in the direction shown.
4. Install the reverse idler gear shaft/holder assembly in the reverse idler gear.
5. Secure the holder with the bolts.
Idler Gear Shaft Removal and Installation
1. Remove the snap ring (A), the cotter retainer (B), and the cotters (C) from the idler gear shaft (D), then remove the idler gear shaft. Do not distort the snap ring.
2. Check the snap ring and the cotter retainer for wear and damage. Replace the snap ring and/or the cotter retainer if the snap ring or the cotter retainer is worn, distorted, or damaged.
3. Install the idler gear shaft in the idler gear shaft bearing.
4. Install the cotters and the cotter retainer, and secure the idler gear shaft with the snap ring.
Shaft Assembly and Housing Installation
Special Tools Required
Snap ring pliers 07LGC-0010100
1. Install the spacer in the torque converter housing with the spacer tab into the guide of the torque converter housing. Do not mix-up the spacers between in the transmission housing and torque converter housing. Install the differential assembly in the torque converter housing, and put the spacer on the differential.
Housing And Shaft:
2. Drive the differential assembly securely in the torque converter housing so there is no clearance.
3. Install the 84 mm thrust shim in the transmission housing.
4. Install the baffle plate.
5. Assemble the mainshaft, countershaft, and secondary shaft.
^ Countershaft reverse selector hub is press-fitted, go to step 6.
^ Countershaft reverse selector hub is not press fitted, go to step 7.
6. Join the mainshaft subassembly (A), countershaft subassembly (B), and secondary shaft subassembly (C) together, and install them in the torque converter housing.
7. Join the countershaft subassembly and secondary shaft subassembly together, then install them in the torque converter housing, and install the mainshaft subassembly. Install the needle bearings, 4th-5th gear, and reverse selector hub over the countershaft.
8. Turn the shift fork shaft (A) so the large chamfered hole (B) is facing the fork bolt hole (C) of the shift fork (D).
9. Install the shift fork and reverse selector together on the shift fork shaft and countershaft. Secure the shift fork to the shift fork shaft with the lock bolt and a new lock washer (E), then bend the lock tab of the lock washer against the bolt head.
10. Install the needle bearing and countershaft reverse gear on the countershaft.
11. Install the reverse idler gear in the transmission housing.
12. Install the three dowel pins (A) and a new gasket (B) on the torque converter housing (C).
13. Align the spring pin (D) of the control shaft (E) with the transmission housing groove (F) by turning the control shaft detent plate. Do not squeeze the end of the control shaft tips together when turning the shaft. If the tips are squeezed together, it will cause a faulty shift position signal or position due to the play between the selector control shaft and the switch.
14. Place the transmission housing (G) on the torque converter housing. Do not install the input shaft (mainshaft) speed sensor and output shaft (countershaft) speed sensor before installing the transmission housing on the torque converter housing.
15. Wrap a screwdriver tip with tape to prevent damage to the reverse idler gear teeth. Engage the reverse idler gear with reverse gears by rotating the idler gear using the screwdriver.
16. Install the transmission housing mounting bolts, and tighten the 16 bolts to 44 Nm (4.5 kgf-m, 33 lbf-ft) in at least two steps in a crisscross pattern.
17. Install the transmission housing mounting bolts from the torque converter housing side, and tighten the three bolts to 44 Nm (4.5 kgf-m, 33 lbf-ft).
18. Install the shift solenoid harness connector (E) with the new O-ring (F) in the transmission housing.
19. Connect WHT and ORN wires connector to shift solenoid valve B. The ATF temperature sensor is assembled in the WHT wire connector.
20. Connect the harness terminals to shift solenoids:
^ BLU wire connector to shift solenoid valve A.
^ GRN wire connector to shift solenoid valve C.
^ YEL wire connector to shift solenoid valve D.
21. Install the shift solenoid valve cover (A), two dowel pins (B), and a new gasket (C).
22. Install the ATF dipstick.