Shift Solenoid Valve Test, Replacement, And Shift Solenoid Wire Harness Replacement (A/T)

Shift Solenoid Valve Test, Replacement, and Shift Solenoid Wire Harness Replacement

1. Connect the HDS to the DLC (A) located under the driver's side of the dashboard.





2. Turn the ignition switch to ON (II). Make sure the HDS communicates with the PCM. If it does not, go to the DLC circuit troubleshooting Testing and Inspection.

3. Select Shift Solenoid Valves A, B, C, D, or E in the Miscellaneous Test Menu on the HDS.

4. Check that shift solenoid valves A, B, C, D, or E operate with the HDS. A clicking sound should be heard.

- If a clicking sound is heard, the valves are OK. The test is complete, disconnect the HDS.
- If no clicking sound is heard, go to step 5.

5. Raise the vehicle on a lift, or apply the parking brake, block both rear wheels, and raise the front of the vehicle. Make sure it is securely supported.

6. Remove the front splash shield Front Splash Shield Replacement.

7. Disconnect the shift solenoid wire harness connector.





8. Measure the resistance between each of the following terminals and body ground:

- No. 1 terminal: Shift solenoid valve C
- No. 2 terminal: Shift solenoid valve B
- No. 3 terminal: Shift solenoid valve E
- No. 5 terminal: Shift solenoid valve A
- No. 8 terminal: Shift solenoid valve D





- If the resistance is within the standard, go to step 9.
- If the resistance is out of the standard, go to step 10.

9. Connect a jumper wire from the battery positive terminal to each shift solenoid wire harness connector terminal individually. A clicking sound should be heard.

- If a clicking sound is heard, the shift solenoid valves and the shift solenoid wire harness are OK. The test is complete, reconnect the connector, then install the front splash shield.
- If no clicking sound is heard, go to step 10.

10. Remove the drain plug (A), and drain the ATF.





11. Reinstall the drain plug with a new sealing washer (B).

12. Remove the left front wheel.

13. Remove the shift solenoid valve cover (A), the dowel pins (B), and the gasket (C).






14. Disconnect the shift solenoid valve connectors from the shift solenoid valve(s) that did not click.





15. Measure the resistance of the shift solenoid valve that was out of the standard between the connector terminal and body ground:





- If the resistance is within the standard, go to step 16.
- If the resistance is out of the standard, go to step 18.

16. Connect a jumper wire from the battery positive terminal to each shift solenoid valve connector terminal individually. A clicking sound should be heard.

- If a clicking sound is heard, go to step 17.
- If no clicking sound is heard, go to step 18.

17. Remove the bolt securing the shift solenoid wire harness (A), replace the shift solenoid wire harness and the O-ring (B), then go to step 24.






18. Remove the shift solenoid valve mounting bolts (F), then hold the shift solenoid valve body, and remove the affected shift solenoid valves.

NOTE: Do not hold the shift solenoid valve connector to remove the shift solenoid valves. Be sure to hold the shift solenoid valve body.





19. Install new O-rings (two O-rings per shift solenoid valve) (G) on the shift solenoid valves.

NOTE: A new shift solenoid valve comes with new O-rings. If you install a new shift solenoid valve, use the O-rings provided with it.

20. If shift solenoid valve C, D, or E was replaced, install shift solenoid valve C (brown connector), shift solenoid valve D (black connector), or shift solenoid valve E (black connector) by holding the shift solenoid valve body; make sure the mounting bracket contacts the servo body.

NOTE: Do not hold the shift solenoid valve connector to install the shift solenoid valve. Be sure to hold the shift solenoid valve body.

21. If shift solenoid valve A was replaced, install shift solenoid valve A (brown connector) by holding the shift solenoid valve body; make sure the mounting bracket contacts the bracket of shift solenoid valve D.

NOTE: Do not install shift solenoid valve A before installing shift solenoid valve D. If shift solenoid valve A is installed before installing shift solenoid valve D, it may damage the hydraulic control system.

22. If shift solenoid valve B was replaced, install shift solenoid valve B (brown connector) by holding the shift solenoid valve body; make sure the mounting bracket contacts the bracket of shift solenoid valve E.

NOTE: Do not install shift solenoid valve B before installing shift solenoid valve E. If shift solenoid valve B is installed before installing shift solenoid valve E, it may damage the hydraulic control system.

23. Install the shift solenoid valve mounting bolts.

24. Connect the shift solenoid valve connectors:

- BLU wire connector to shift solenoid valve A.
- ORN wire connector to shift solenoid valve B.
- GRN wire connector to shift solenoid valve C.
- YEL, WHT, and WHT wire connector to shift solenoid valve D.
- RED wire connector to shift solenoid valve E.

25. Install a new gasket, the dowel pins, and the shift solenoid valve cover.

26. Check the connector for corrosion, dirt, or oil, and clean or repair if necessary, then connect the connector securely.

27. Refill the transmission with ATF.

28. Install the front splash shield Front Splash Shield Replacement.

29. Install the left front wheel.