Installation

Carpet Removal and Installation

Installation

SRS components are located in this area. Review the SRS component locations Locations and the precautions and procedures Service and Repair before doing repairs or service.

1. Floor Carpet - 4-Door (M/T)





1. If necessary, install the floor mat holder (A).





2. When installing the new carpet, cut the carpet in the area (A) as shown.

3. Pass the seat harnesses (B), then install the carpet (C).

4. Install the hook and loop fastener (D).

5. Install the clips (E).

Without load ABS box





With load ABS box





6. Connect the connectors (A), and install the harness clips (B).





7. Connect the connectors (A), and install the harness clips (B).





8. Install the HVAC bracket (A).

2. Footrest





1. For some models: Install the upper clip (A) to the stud bolt (B).

2. For some models: Install the lower clip (C) to the stud bolt (D), then install the footrest (E).

3. Steering Joint Cover





1. Install the steering joint cover (A) in the sequence shown.

4. Center Console





1. Install the center console (A).





2. Connect the connector (A).





3. Install the bolts (A).

4. Install the console box mat (B).





5. Connect the connector (A).

6. Install the bolts (B).

5. Cup Holder Panel Assembly





1. Install the cup holder panel assembly (A).

6. Center Console Panel





1. Install the center console panel (A).

7. Shift Lever Knob





Except K24Z7 engine

1. Install the shift lever knob (A).

NOTE: Tighten the shift lever knob until the shift pattern is properly aligned.

2. Connect the shift lever boot (B).





K24Z7 engine

1. Install and turn the shift lever boot ring (A) until it reaches the bottom of the threads on the shift lever.

2. Turn the shift lever knob (B) until the shift lever knob contacts the shift lever boot ring.

3. Tighten the shift lever boot ring and the shift lever knob together with the shift pattern properly aligned.

4. Connect the shift lever boot (C).

8. Both B-Pillar Lower Trims





1. Install the B-pillar lower trim (A).

2. The left side is shown; repeat on the right side.

9. Both Rear Door Opening Seals as Needed





1. Install the rear door opening seal (A).

2. The left side is shown; repeat on the right side.

10. Front Door Opening Seal as Needed Both





1. Install front door opening seal (A).

2. Repeat on the opposite side.

11. Both Rear Door Sill Trims





1. While pulling up the rear seat cushion (A), install the rear door sill trim (B).

2. Push down the seat cushion, then install the hook (C) to the rear seat cushion clip (D).

3. The left side is shown; repeat on the right side.

12. Both Kick Panels

Driver's side





Passenger's side





1. Install both kick panels (A).

2. Install both front door opening seals (B) as needed.

13. Both Front Door Sill Trims

Driver's side





Passenger's side





1. Install both front door sill trims (A).





2. Driver's side: Install the screw (A).





3. Driver's side: Install the opener lock cylinder (A).

4. Driver's side: Install the cap (B) to the front door sill trim (C).

14. Rear Seat Cushion





1. Install the hooks (A) to the rear seat cushion clips (B).





2. Install the bolt (A) securing the rear seat cushion (B).

15. Both Front Seats

Power seat





Manual seat





1. With the help of an assistant, carefully install both front seats through the front door opening.

2. Install the harness clips (A).

3. Connect the connectors (B).

4. The driver's seat is shown; repeat on the passenger's seat.

Front side





Rear side





5. Install the seat mounting bolts (A).

NOTE: Tighten the bolts to the specified torque in the sequence shown.
* Tighten the bolts by hand first, then tighten them to the specified torque.
* Tighten the seat mounting bolts to the specified torque in the sequence shown. Slide the seat all the way back and tighten 1 and 2, then slide it forward and tighten 3 and 4.

6. The driver's seat is shown; repeat on the passenger's seat.





7. Install both seat track end covers (A).

8. The driver's seat is shown; repeat on the passenger's seat.

16. Both Front Seat Belt Lower Anchor Bolts





1. Install the lower anchor bolt (A).

2. The driver's seat is shown; repeat on the passenger's seat.





3. Install the anchor cover (A).

4. The driver's seat is shown; repeat on the passenger's seat.

17. Battery Terminal (SRS) - Reconnection





NOTE: If the battery performs abnormally, test the battery.

1. Clean the battery terminals.

2. Connect the positive cable (A) to the battery (B).

NOTE: Always connect the positive side first.

3. Connect the negative cable and battery sensor (C) to the battery.

4. Apply multipurpose grease to the terminals to prevent corrosion.