Seat Belt Shoulder Anchor Adjuster Removal and Installation
Seat Belt Shoulder Anchor Adjuster Removal and Installation
Removal
SRS components are located in this area. Review the SRS component locations Locations and the precautions and procedures Service and Repair before doing repairs or service.
1. Battery Terminal (SRS) - Disconnection
1. Make sure the ignition switch is in LOCK (0).
2. Disconnect and isolate the negative cable and battery sensor (A) from the battery (B).
NOTE: Always disconnect the negative side first.
3. Disconnect the positive cable (C) from the battery.
4. Wait at least 3 minutes before starting work.
2. Front Seat Belt Lower Anchor Bolt - Driver's Side
2-door
1. Remove the lower anchor cap (A).
2. Remove the lower anchor bolt (B).
4-door
1. Remove the anchor cover (A).
2. Remove the lower anchor bolt (A).
3. Front Door Sill Trim - 4-Door
1. Remove the cap (A) from the front door sill trim (B).
2. Remove the opener lock cylinder (C).
3. Remove the screw (A).
4. Remove the front door sill trim (A).
4. Rear Door Sill Trim
1. While pushing down on the rear seat cushion (A), pull the seat hook handle (B) to release the hook (C).
2. While pulling up the seat cushion, remove the rear door sill trim (D).
5. Front and Rear Door Opening Seals as Needed
Front
Rear
1. Remove the front door opening seal (A) and the rear door opening seal (B) as needed.
6. B-Pillar Lower Trim
1. Slide the front seat forward fully.
2. Remove the B-pillar lower trim (A).
7. B-Pillar Upper Trim
1. Remove the bottom area of the B-pillar upper trim (A).
2. Remove the upper area of the B-pillar upper trim (A).
3. Pass the front seat belt lower anchor (A) out through the hole in the slider (B), then remove the B-pillar upper trim (C).
8. Front Seat Belt Upper Anchor Bolt - Driver's Side
2-door
4-door
1. Remove the upper anchor bolt (A).
9. Front Seat Shoulder Anchor Adjuster
1. Remove the shoulder anchor adjuster (A).
Installation
SRS components are located in this area. Review the SRS component locations Locations and the precautions and procedures Service and Repair before doing repairs or service.
1. Front Seat Shoulder Anchor Adjuster
1. Install the shoulder anchor adjuster (A).
2. Front Seat Belt Upper Anchor Bolt - Driver's Side
1. Assemble the washer, the collar, and the bushing on the upper anchor bolt as shown.
NOTE: Apply medium strength liquid thread lock to the upper anchor bolt before reinstallation.
2-door
4-door
2. Install the upper anchor bolt (A).
3. B-Pillar Upper Trim
1. Pass the front seat belt lower anchor (A) in through the hole in the slider (B).
2. Install the upper area of the B-pillar upper trim (A).
3. Install the bottom area of the B-pillar upper trim (A).
4. B-Pillar Lower Trim
1. Install the B-pillar lower trim (A).
5. Front and Rear Door Opening Seals as Needed
Front
Rear
1. Install the front door opening seal (A) and the rear door opening seal (B).
6. Rear Door Sill Trim
1. While pulling up the rear seat cushion (A), install the rear door sill trim (B).
2. Push down the seat cushion, then install the hook (C) to the rear seat cushion clip (D).
7. Front Door Sill Trim - 4-Door
1. Install the front door sill trim (A).
2. Install the screw (A).
3. Install the opener lock cylinder (A).
4. Install the cap (B) to the front door sill trim (C).
8. Front Seat Belt Lower Anchor Bolt - Driver's Side
2-door
1. Assemble the washer, the collar, and the bushing on the lower anchor bolt as shown.
NOTE: Apply medium strength liquid thread lock to the lower anchor bolt before reinstallation.
2. Install the lower anchor bolt (A).
3. Install the anchor cover (B).
4-door
1. Install the lower anchor bolt (A).
2. Install the anchor cover (A).
9. Battery Terminal (SRS) - Reconnection
NOTE: If the battery performs abnormally, test the battery.
1. Clean the battery terminals.
2. Connect the positive cable (A) to the battery (B).
NOTE: Always connect the positive side first.
3. Connect the negative cable and battery sensor (C) to the battery.
4. Apply multipurpose grease to the terminals to prevent corrosion.