Parasitic Draw Check
Parasitic Draw Check
Special Tools Required
LH41 AC/DC low current clamp meter, FLULH41A*
*: Available through the Honda Tool and Equipment
Program, 888-424-6857
1. Make sure the battery is fully charged, and that all the vehicle's electrical accessories are turned off.
2. Open the hood.
3. Disconnect the security hood switch 2P connector to allow the security system to arm itself with the hood open.
4. Turn the ignition switch to ON (II).
5. Turn the ignition switch to LOCK (0), and remove the ignition key from the ignition switch.
6. Get out of the vehicle, and close all the doors and the tailgate.
7. Lock the doors with the keyless transmitter.
8. Make sure the front individual map lights, interior light, and ceiling light switches are turned off, and the security alarm system is armed by confirming that the security indicator is flashing.
9. Wait at least 20 minutes.
10. Attach the LH41 AC/DC low current clamp meter (A) to the battery ground cable (B). Follow the equipment manufacturer's instructions, then measure the parasitic draw.
NOTE: If you are using a digital multimeter, go to step 11.
Is the parasitic draw for USA models 37 mA, for Canada models 46 mA, or less?
YES -
The system is normal at this time.
NO -
Go to step 17.
11. Check the following items before measuring:
- The multimeter dial is set to the DCA (direct current amps) range.
- The red test probe is plugged into the red A (Amps) jack, and the black test probe is plugged into the COM jack.
- To avoid blowing an input fuse, start by setting the range above 10 A.
12. Loosen the nut (A) on the battery negative terminal.
NOTE: Follow the instructions exactly to avoid disconnecting the battery ground cable terminal from the battery negative terminal.
13. Connect the red (+) test lead (A) to the negative terminal (B) of the battery ground cable.
14. Slide the negative terminal of the battery ground cable upwards from the battery negative terminal so that it still makes contact and avoids disconnection. Then connect the black (-) test lead (C) to the battery negative terminal post.
15. Disconnect the negative terminal (A) of the battery ground cable from the battery negative terminal.
16. Measure the parasitic draw.
Is the parasitic draw for USA models 37 mA, for Canada models 46 mA, or less?
YES -
The system is normal at this time.
NO -
Go to step 17.
17. Check if there are any aftermarket electrical accessories installed on the vehicle.
Are there any aftermarket electrical accessories installed?
YES -
Go to step 18.
NO -
Go to step 20.
18. Make sure that the aftermarket electrical accessories have been properly installed.
Are the aftermarket electrical accessories installed correctly?
YES -
Go to step 19.
NO -
Repair, reinstall, or remove the aftermarket accessories, then recheck.
19. Disconnect the aftermarket electrical accessories one at a time, then measure the parasitic draw.
1. Turn the ignition switch to ON (II) and then back to LOCK (0).
2. Get out of the vehicle and close all doors.
3. Wait at least 40 seconds.
4. Measure the parasitic draw.
Is the parasitic draw for USA models 37 mA, for Canada models 46 mA, or less?
YES -
Replace or repair the aftermarket electrical accessory that reduced the parasitic draw to for USA models 37 mA, for Canada models 46 mA, or less when disconnected.
NO -
Go to step 20.
20. Remove the No. A15 (10 A) fuse in the under-hood fuse/relay box, then measure the parasitic draw.
Is the parasitic draw for USA models 24 mA, for Canada models 32 mA or less?
YES -
Go to step 21.
NO -
Go to step 23.
21. Connect immobilizer-keyless control unit 7P connector terminal No. 4 and body ground with a jumper wire.
22. Install the No. A15 (10 A) fuse to the under-hood fuse/relay box, then measure the parasitic draw.
1. Turn the ignition switch to ON (II), and then back to LOCK (0).
2. Get out of the vehicle and close all doors.
3. Wait at least 40 seconds.
4. Measure the parasitic draw.
Is the parasitic draw for USA models 37 mA, for Canada models 46 mA, or less?
YES -
Disconnect the control units from the B-CAN circuit one at a time, perform steps 1-4 above, then measure the parasitic draw. Do the input test for the control unit that reduced the parasitic draw to for USA models 37 mA, for Canada models 46 mA, or less when disconnected.
NO -
Disconnect the control units from the No. A15 (10 A) fuse circuit one at a time, perform steps 1-4 above, then measure the parasitic draw. Replace the control unit that reduced the parasitic draw to for USA models 37 mA, for Canada models 46 mA, or less when disconnected.
23. Remove the No. A3-1 (IG MAIN) (50 A) fuse in the under-hood fuse/relay box, then measure the parasitic draw.
1. Turn the ignition switch to ON (II) and then back to LOCK (0).
2. Get out of the vehicle and close all doors.
3. Wait at least 40 seconds.
4. Measure the parasitic draw.
Is the parasitic draw for USA models 37 mA, for Canada models 46 mA, or less?
YES -
Go to step 24.
NO -
Remove the fuses from the fuse box one at a time, perform steps 1-4 above, then measure the parasitic draw in order to isolate the circuit which contains the fault. If all circuits are OK, check the starter circuits and do the starter performance test Testing and Inspection.
24. Install the No. A3-1 (IG MAIN) (50 A) fuse in the under-hood fuse/relay box.
25. Disconnect the ignition switch 5P connector, then measure the parasitic draw.
Is the parasitic draw for USA models 37 mA, for Canada models 46 mA, or less?
YES -
Replace the ignition switch Service and Repair.
NO -
Repair a short to ground in the wire between the No. A3-1 (IG1 MAIN) (50 A) fuse in the under-hood fuse/relay box and power control unit.