Front Seat Outer Belt Assembly

Front Seat Outer Belt Assembly:

Front Seat Outer Belt Assembly:

FRONT SEAT OUTER BELT ASSEMBLY

REMOVAL

HINT:
- Use the same procedures for the LH side and RH side.
- The procedures listed below are for the LH side.

1. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY
2. REMOVE FRONT SEAT ASSEMBLY
3. REMOVE COWL TOP VENTILATOR LOUVER RH
4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

NOTE: After the engine switch is turned off, the HDD navigation system requires approximately 6 minutes to record various types of memory and settings. As a result, after turning the engine switch off, wait 6 minutes or more before disconnecting the cable from the negative (-) battery terminal.

5. REMOVE FRONT DOOR SCUFF PLATE
6. REMOVE REAR DOOR SCUFF PLATE
a. for Standard Body:
1. Remove the rear door scuff plate.

b. for Long Body:
1. Remove the rear door scuff plate.

7. REMOVE CENTER PILLAR GARNISH LOWER
8. REMOVE CENTER PILLAR GARNISH UPPER
9. REMOVE FRONT SEAT SHOULDER BELT GUIDE




a. Remove the 2 screws and belt guide.

10. REMOVE FRONT SEAT OUTER BELT ASSEMBLY




a. Remove the nut and shoulder anchor.




b. Disconnect the pretensioner connector as shown in the illustration labeled A.
c. Disconnect the tension reducer connector labeled B.
d. w/ Pre-collision system:
Disconnect the pre-collision connector labeled C.




e. Remove the 2 bolts and seat belt.

INSTALLATION

HINT:
- Use the same procedures for the LH side and RH side.
- The procedures listed below are for the LH side.
- A bolt without a torque specification is shown in the standard bolt chart.

1. INSTALL FRONT SEAT OUTER BELT ASSEMBLY

NOTE: When installing the retractor, make sure the vehicle's claws (labeled "a" in the illustration) only contact the installation areas of the retractor.




a. Align the vehicle's claws with the seat belt retractor positioning holes.
b. Install the seat belt with the 2 bolts. First install the upper bolt, and then install the lower bolt.

Torque: 7.5 N.m (76 kgf.cm, 66 in.lbf) for bolt A

Torque: 42 N.m (428 kgf.cm, 31 ft.lbf) for bolt B




c. Connect the pretensioner connector labeled A, as shown in the illustration.
d. Connect the tension reducer connector labeled B.
e. w/ Pre-collision system:
Connect the pre-collision connector labeled C.




f. Install the shoulder anchor to the shoulder belt anchor adjuster with the nut.

Torque: 42 N.m (428 kgf.cm, 31 ft.lbf)

2. INSTALL FRONT SEAT SHOULDER BELT GUIDE




a. Install the belt guide with the 2 screws.

NOTE: Make sure the belt is not pinched as this may damage the belt.

3. INSTALL CENTER PILLAR GARNISH UPPER
4. INSTALL CENTER PILLAR GARNISH LOWER
5. INSTALL REAR DOOR SCUFF PLATE
a. for Standard Body:
1. Install the rear door scuff plate.

b. for Long Body:
1. Install the rear door scuff plate.

6. INSTALL FRONT DOOR SCUFF PLATE
7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
8. INSTALL COWL TOP VENTILATOR LOUVER RH
9. INSTALL FRONT SEAT ASSEMBLY
10. CONNECT FRONT SEAT OUTER BELT ASSEMBLY
11. PERFORM INITIALIZATION
a. Perform initialization.

NOTE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.

12. CHECK SRS WARNING LIGHT
a. Check the SRS warning light.