Diesel Data: Automotive Repair
Home >> Lexus >> 2008 >> ES 350 V6-3.5L (2GR-FE) >> Repair and Diagnosis >> Body and Frame >> Interior Moulding / Trim >> Headliner >> Service and Repair >> Installation

Installation








INTERIOR: ROOF HEADLINING:

INSTALLATION

1. INSTALL NO. 1 ROOF WIRE (for Standard)
(a) Apply new double-sided tape to the locations shown in the illustration while aligning the tape with the markings on the roof headlining.





NOTE: Securely apply the double-sided tape to prevent the tape from being out of alignment and peeling off.

(b) Peel off the release paper from the double-sided tape.
(c) Attach the No. 1 roof wire along the double-sided tape so that the marking surface of the wire harness faces downward.
NOTICE:
- Securely attach the No. 1 roof wire.
- Failure to do so may cause abnormal noise.

(d) Turn the visor connectors clockwise approximately 90° to the connectors of the roof headlining.
(e) Apply adhesive tape to the locations shown in the illustration.





HINT: As shown at point A in the illustration, line up and secure the reference tape of the wire harness to the tip of the roof headlining assembly.

2. INSTALL NO. 1 ROOF WIRE (for Glass Roof)
(a) Apply new double-sided tape to the locations shown in the illustration while aligning the tape with the markings on the roof headlining.





NOTE: Securely apply the double-sided tape to prevent the tape from being out of alignment and peeling off.

(b) Peel off the release paper from the double-sided tape.
(c) Attach the No. 1 roof wire along the double-sided tape so that the marking surface of the wire harness faces downward.
NOTICE:
- Securely attach the No. 1 roof wire.
- Failure to do so may cause abnormal noise.

(d) Turn the visor connectors clockwise approximately 90° to the connectors of the roof headlining.
(e) Apply adhesive tape to the locations shown in the illustration.





HINT: As shown at point A in the illustration, line up and secure the reference tape of the wire harness to the tip of the roof headlining assembly.

3. INSTALL VANITY LIGHT ASSEMBLY






(a) Install the vanity light to the roof headlining.
(b) Connect the 2 claws to install the bulb holder.
HINT: Use the same procedure to install the light on the other side.

4. INSTALL ANTENNA CORD SUB-ASSEMBLY Installation

5. INSTALL ROOF HEADLINING ASSEMBLY (for Standard)






(a) Pull the roof headlining assembly into the vehicle through the front right door.
(b) Engage the 12 claws, 4 clips, and 11 fasteners.
(c) Connect the antenna cord sub-assembly connector and engage the clamp to the rear pillar RH.
(d) Connect the antenna cord sub-assembly connector and engage each clamp to the front pillar RH.
(e) Connect the No. 1 wire connector and engage each clamp to the front pillar LH.





6. INSTALL ROOF HEADLINING ASSEMBLY (for Glass Roof)






(a) Pull the roof headlining assembly into the vehicle through the front right door.
(b) Engage the 12 claws, 4 clips, and 21 fasteners.
(c) Connect the antenna cord sub-assembly connector and engage the clamp to the rear pillar RH.
(d) Connect the antenna cord sub-assembly connector and engage each clamp to the front pillar RH.
(e) Connect the No. 1 wire connector and engage each clamp to the front pillar LH.





7. INSTALL ASSIST GRIP SUB-ASSEMBLY
(a) Engage the 2 clips to an assist grip sub-assembly as shown in the illustration.






(b) Install the assist grip sub-assembly.
(c) Install the 2 assist grip covers to the assist grip sub-assembly.
HINT: Use the same procedure for the other 3 assist grips.

8. INSTALL SPOT LIGHT ASSEMBLY (for Standard)






(a) Connect the connector.






(b) Engage the 2 clips and install the spot light assembly.
9. INSTALL SPOT LIGHT ASSEMBLY (for Glass Roof)






(a) Connect the connector.






(b) Engage the 2 clips and install the spot light assembly.
10. INSTALL COAT HOOK






(a) Install the coat hook with the screw.
HINT: Use the same procedure to install the hook on the other side.

11. INSTALL VISOR HOLDER






(a) Set the claws of the visor holder as shown in the illustration.
(b) Engage the claws and install the visor holder.
HINT: Use the same procedure to install the holder on the other side.

12. INSTALL VISOR ASSEMBLY LH






(a) Install the visor assembly LH with the 2 screws.
13. INSTALL VISOR ASSEMBLY RH
HINT: Use the same procedure for the RH side and the LH side.

14. INSTALL VISOR BRACKET COVER






(a) Engage the 4 claws and install the visor bracket cover.
HINT: Use the same procedure to install the cover on the other side.

15. INSTALL ROOF CONSOLE BOX ASSEMBLY






(a) Connect the connector.
(b) Engage the 2 clips.






(c) Install the roof console box assembly with the 2 screws.
16. INSTALL RAIN SENSOR COVER (w/ Rain Sensor) Installation

17. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER Installation

18. CONNECT STEREO COMPONENT AMPLIFIER ASSEMBLY CONNECTOR (w/ DVD Player)






(a) Connect the stereo component amplifier assembly connector.
19. INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER RH (w/ DVD Player) Reassembly

20. INSTALL REAR FLOOR FINISH PLATE (w/ DVD Player) Reassembly

21. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (w/ DVD Player) Reassembly

22. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (w/ DVD Player) Reassembly

23. INSTALL SPARE WHEEL COVER TRAY (w/ DVD Player)
24. INSTALL LUGGAGE COMPARTMENT FLOOR MAT (w/ DVD Player)
25. INSTALL FLOOR CARPET BRACKET LH
26. INSTALL FLOOR CARPET BRACKET RH
27. INSTALL SHIFT LEVER ASSEMBLY Installation

28. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY Installation

29. INSTALL NO. 2 CONSOLE BOX DUCT Installation

30. INSTALL NO. 3 CONSOLE BOX DUCT Installation

31. INSTALL REAR CONSOLE BOX ASSEMBLY Installation

32. INSTALL CONSOLE REAR END PANEL SUB-ASSEMBLY Installation

33. INSTALL CONSOLE BOX CARPET Installation

34. INSTALL CONSOLE BOX POCKET Installation

35. INSTALL HEATER SEAT SWITCH CONSOLE BASE (w/o Seat Heater System) Installation

36. INSTALL HEATER SEAT SWITCH CONSOLE BASE (w/ Seat Heater System) Installation

37. INSTALL UPPER CONSOLE PANEL ASSEMBLY WITH FRONT ASH RECEPTACLE Installation

38. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY Installation

39. INSTALL INSTRUMENT PANEL FINISH PANEL END LH Installation

40. INSTALL INSTRUMENT PANEL FINISH PANEL END RH Installation

41. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH






(a) Engage the claw and 5 clips, and install the roof side inner garnish assembly LH.
42. INSTALL REAR SEAT SIDE GARNISH LH (w/o Rear Seat Side Airbag)






(a) Install the 4 claws and install the rear seat side garnish LH.
43. INSTALL REAR SEAT SIDE AIRBAG ASSEMBLY LH (w/ Rear Seat Side Airbag) Installation

44. INSTALL UPPER CENTER PILLAR GARNISH LH






(a) Engage the clip.
(b) Install the upper center pillar garnish LH with the 2 screws.
45. INSTALL LOWER CENTER PILLAR GARNISH LH






(a) Engage the 5 clips and 2 claws, and install the lower center pillar garnish LH.
46. INSTALL REAR DOOR SCUFF PLATE LH






(a) Engage the 8 claws, then install the rear door scuff plate LH.
47. INSTALL FRONT PILLAR GARNISH LH






(a) Remove the protective cover.






(b) Install a new clip [A] on the front pillar garnish LH.
(c) Engage the claw and 2 clips, then install the front pillar garnish LH.
48. INSTALL SIDE INSTRUMENT PANEL LH Installation

49. INSTALL FRONT DOOR OPENING TRIM COVER LH






(a) Engage the 3 claws and install the front door opening trim cover LH.
50. INSTALL FRONT DOOR SCUFF PLATE LH






(a) Engage the 12 claws, and install the front door scuff plate LH.
51. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH
HINT: Use the same procedure for the RH side and the LH side.

52. INSTALL REAR SEAT SIDE GARNISH RH (w/o Rear Seat Side Airbag)
HINT: Use the same procedure for the RH side and the LH side.

53. INSTALL REAR SEAT SIDE AIRBAG ASSEMBLY RH (w/ Rear Seat Side Airbag)
HINT: Use the same procedure for the RH side and the LH side.

54. INSTALL UPPER CENTER PILLAR GARNISH RH
HINT: Use the same procedure for the RH side and the LH side.

55. INSTALL LOWER CENTER PILLAR GARNISH RH
HINT: Use the same procedure for the RH side and the LH side.

56. INSTALL REAR DOOR SCUFF PLATE RH
HINT: Use the same procedure for the RH side and the LH side.

57. INSTALL FRONT PILLAR GARNISH RH
HINT: Use the same procedure for the RH side and the LH side.

58. INSTALL SIDE INSTRUMENT PANEL RH Installation

59. INSTALL FRONT DOOR OPENING TRIM COVER RH
HINT: Use the same procedure for the RH side and the LH side.

60. INSTALL FRONT DOOR SCUFF PLATE RH
HINT: Use the same procedure for the RH side and the LH side.

61. INSTALL FRONT SEAT ASSEMBLY LH Installation

62. INSTALL FRONT SEAT REAR OUTER TRACK BRACKET COVER LH Installation

63. INSTALL FRONT SEAT REAR INNER TRACK BRACKET COVER LH Installation

64. INSTALL FRONT SEAT OUTER TRACK BRACKET COVER LH Installation

65. INSTALL FRONT SEAT INNER TRACK BRACKET COVER LH Installation

66. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH Installation

67. INSTALL SEAT BELT ANCHOR COVER CAP LH Installation

68. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Driver Seat)
69. INSTALL FRONT SEAT ASSEMBLY RH Installation

70. INSTALL FRONT SEAT REAR OUTER TRACK BRACKET COVER RH Installation

71. INSTALL FRONT SEAT REAR INNER TRACK BRACKET COVER RH Installation

72. INSTALL FRONT SEAT OUTER TRACK BRACKET COVER RH Installation

73. INSTALL FRONT SEAT INNER TRACK BRACKET COVER RH Installation

74. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH Installation

75. INSTALL SEAT BELT ANCHOR COVER CAP RH Installation

76. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Front Passenger Seat)
77. INSTALL REAR SEATBACK ASSEMBLY Installation

78. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY
79. INSTALL REAR SEAT HEADREST ASSEMBLY
80. INSTALL REAR SEAT CUSHION ASSEMBLY Installation

81. PERFORM INITIALIZATION
NOTE: Some systems need initialization after reconnecting the cable to the negative battery terminal Repair Instruction - Initialization.

82. INSPECT SHIFT LEVER POSITION Adjustments

83. ADJUST SHIFT LEVER POSITION Adjustments

84. INSPECT FRONT SEAT ASSEMBLY Installation

85. INSPECT SRS WARNING LIGHT Diagnosis System
Diesel-Data.com