Brake Caliper Inspection (Front)
Brake Caliper Inspection (Front)
Caution: Refer to Brake Dust Caution (Brake Dust Caution) in Cautions and Notices.
Caution: Refer to Brake Fluid Irritant Caution (Brake Fluid Irritant Caution) in Cautions and Notices.
1. Inspect the fluid level in the master cylinder reservoir.
* If the brake fluid level is midway between the maximum-fill level and the minimum allowable level, no brake fluid needs to be removed from the master cylinder reservoir before proceeding.
Important: DO NOT completely empty the master cylinder reservoir or remove any brake lines otherwise complete bleeding of the braking system will be necessary.
Important: DO NOT reuse the removed fluid.
* If the brake fluid level is higher than midway between the maximum-fill level and the minimum allowable level, syphon the brake fluid to the midway point using a hand vacuum pump before proceeding.
2. Remove wheels. Refer to Tire and Wheel Removal and Installation (Service and Repair) in Tires and Wheels.
3. Install two wheel nuts (1) in reverse to opposite wheel studs to retain the brake disc to the hub.
Important: Position the ends of the G-clamps against the rear of the brake caliper (2) and against the outboard brake pad (3).
4. Install large G-clamps over the body of the brake caliper (2).
Important: The movement of a brake caliper piston into a brake caliper bore should be smooth and even. If a brake caliper piston is frozen or difficult to bottom out, the brake caliper requires overhaul or replacement.
Inspect for smooth and complete travel of the brake caliper pistons, into the brake caliper bores.
Tighten the G-clamps until the brake caliper pistons bottom out in the brake caliper bores.
5. Remove the G-clamps from the brake caliper (2).
6. Grasp the brake caliper (2) and try to move the brake caliper (2) up or down.
The brake caliper (2) should have minimal freeplay.
7. Grasp the brake caliper (2) and try to move the brake caliper (2) in and out.
The brake caliper (2) should slide smoothly with minimal force.
Important: DO NOT disconnect the hydraulic brake flexible hose from the brake caliper.
8. Remove the brake caliper (2). Refer to Front Brake Caliper Replacement (Front Brake Caliper Replacement) .
Notice: Support the brake caliper with heavy mechanic wire, or equivalent, whenever it is separated from its mount and the hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak.
9. Inspect the brake caliper to steering knuckle retaining bolts for the following:
* Bent or damaged brake caliper to steering knuckle retaining bolts.
* Binding.
* Corrosion.
* Seizing in the knuckle.
10. If any of the conditions listed are found, replace the brake caliper to steering knuckle retaining bolts.
11. Remove the brake caliper lower guide pin retaining bolts (1).
12. Inspect the brake caliper guide pins (2) for a smooth operation. Gently pull the brake caliper guide pins (2) outward without disengaging the guide from the brake caliper boots (3). Push the brake caliper guide pins (2) inward, and inspect for the following:
* Bent or damaged brake caliper guide pin retaining bolts (1).
* Bent or damaged brake caliper guide pins (2).
* Binding.
* Corrosion.
* Seizing.
13. If any of the conditions listed are found, replace the brake caliper guide pins (2).
14. Inspect the brake caliper boots (3) for the following:
* Missing brake caliper boots (3).
* Cracked or torn brake caliper boots (3).
15. If any of the conditions listed are found, replace the brake caliper boots (3).
16. Inspect the brake caliper (2) and brake caliper anchor plate (4) for the following:
* Bent or damaged brake caliper anchor plate (4).
* Excessive brake caliper guide pin (3) play in the brake caliper anchor plate (4).
* Excessive brake caliper guide bolt (1) play in the brake caliper (2).
* Corrosion.
* Cracks.
* Damage.
* Excessive wear.
17. If any of the conditions listed are found, replace the brake caliper (2).
18. Inspect the brake caliper piston dust boot seals (2) for cracks, tears, cuts, deterioration and/or incorrect seating in the brake caliper (1). If any of these conditions are present, the brake caliper requires overhaul or replacement.
19. Inspect for brake fluid leakage around the brake caliper piston dust boot seals (2) and on the brake pads. If there is any evidence of brake fluid leakage, overhaul or replace the brake caliper (1).