Part 1
Fuel System Description
The fuel system is comprised of two subsystems. The fuel supply system and the fuel metering system. The correct amount of fuel can not be delivered to the engine cylinders without a constant supply of air from the air intake system. The air intake system provides measured clean air to each cylinder for proper mixture with the pressurized fuel. The powertrain control module (PCM), along with the information sensors and switches, controls the activity between all three systems.
Fuel System Components with FWD
1 - Fuel Tank
2 - Fuel Sender Assembly, includes fuel pump
3 - EVAP Canister
4 - Fuel Filler Pipe
5 - Quick Connect Fuel Line Fitting, tank
6 - Fuel and EVAP Lines
7 - Quick Connect Fuel Line Fitting, engine
8 - Fuel Injectors
Fuel System Components with AWD
1 - Fuel Tank
2 - EVAP Canister
3 - Fuel Sender Assembly, includes fuel pump
4 - Fuel Filler Pipe
5 - Quick Connect Fuel Line Fitting, tank
6 - Fuel and EVAP Lines
7 - Quick Connect Fuel Line Fitting, engine
8 - Fuel Injectors
The fuel supply system is a returnless on-demand design, that reduces evaporative emissions. The fuel metering system is a sequential fuel injection (SFI) design. The function of the fuel metering system is deliver the correct amount of fuel to the engine under all operating conditions. The main component of the vehicle's fuel metering system is the fuel injectors. There is one fuel injector for each cylinder. The fuel injectors are controlled sequentially by the PCM. The PCM bases the control of the fuel injectors on several important engine parameters. These engine parameters include the following:
* The mass air flow (MAF) sensor
* The intake air temperature (IAT) sensor
* The engine coolant temperature (ECT) sensor
* The throttle position (TP) sensor
* The accelerator pedal position (APP) sensor, FWD only
* The engine speed (RPM)
* The heated oxygen sensor (HO2S)
The engine is designed to use only unleaded fuel. Unleaded fuel must be used for proper emission control system operation. Using unleaded fuel will also decrease spark plug fouling and extend engine oil life. Leaded fuel can damage the emission control system. The use of leaded fuel can result in the loss of emission warranty coverage.
The vehicle fuel system is equipped with an evaporative emission (EVAP) control system that minimizes the release of fuel vapors to the atmosphere. For more information on the EVAP system, refer to Evaporative Emission Control System Description (Evaporative Emission Control System Description).
Fuel Supply System
1 - Fuel Pressure Gauge Adapter J 42982
2 - Fuel Feed Pipe
3 - Fuel Sender Assembly
4 - Fuel Tank
5 - Fuel Pressure Regulator
6 - Fuel Pump
7 - Fuel Sender (gauge)
8 - Fuel Filter
9 - Pinch Off Area
10 - Fuel Pressure Gauge J 34730-1A
11 - Fuel Injectors
12 - Fuel Rail
13 - Fuel Pulsation Damper
The supply of fuel is stored in the fuel tank. An electric fuel pump pressurizes the fuel to the fuel filter, out to the fuel lines and thru the fuel pulsation damper to the fuel rail. The electric fuel pump is suspended from the top of the fuel tank as part of the fuel sender assembly. The fuel pump is designed to provide fuel at a pressure above the regulated pressure needed by the fuel injectors. The fuel pressure regulator keeps the fuel supplied to the fuel injectors at the regulated pressure.
The fuel pressure regulator is located inside of the fuel tank and is part of the fuel sender assembly. Locating the fuel pressure regulator in the fuel tank eliminates the need for a return line from the fuel rail. A returnless system reduces the internal temperature of the fuel tank resulting in lower evaporative emissions.
The fuel system is also equipped with an enhanced evaporative emission system and an on-board refueling vapor recovery (ORVR) system. Together the 2 systems minimize the release of fuel vapors to the atmosphere.
Fuel Tank Assembly - FWD
1 - Fuel Supply Line
2 - Retaining Clip
3 - ORVR Vent Line
4 - Fuel Filler Cap
5 - Fuel Filler Pipe Assembly
6 - Fuel Filler Hose
7 - Fuel Filler Hose Protector
8 - Fuel Tank Straps
9 - Fuel Tank
10 - Fuel Sender Assembly Gasket
11 - Fuel Sender Assembly
12 - Fuel Tank Lock Ring
Fuel Tank Assembly - AWD
1 - Hold Down Plate for Fuel Sender Assembly
2 - Fuel Sender Assembly
3 - Fuel Sender Assembly Gasket
4 - Fuel Filler Vent Line
5 - Fuel Filler Cap
6 - Fuel Filler Pipe Assembly
7 - Fuel Filler Hose
8 - Protective Cover for Fuel Filler Hose
9 - Fuel Tank Straps
10 - Fuel Tank
11 - Fuel Sender Assembly Gasket
12 - Fuel Limiter Vent Valve (FLVV) Assembly
13 - Hold Down Plate for FLVV Assembly
14 - Fuel Limiter Vent Valve (FLVV) Cover
Fuel Tank (FWD)
The fuel tank used on the front wheel drive (FWD) vehicle is made of a composite material. The composite material is actually several layers of materials. The outside and inside layers are a high density polyethylene, with a center layer of recycled material and ethylene vinyl alcohol copolymer. The fuel tank is located beneath the rear seat area. The tank is held in place with two straps that are secured with bolts. The shape of this tank was designed to allow for a constant supply of fuel around the fuel pump strainer during low fuel conditions and also during aggressive vehicle maneuvers. The fuel inlet port on the tank is equipped with an inlet valve. This fuel tank inlet valve prevents the fuel from spewing into the fuel filler neck during aggressive vehicle maneuvers or vehicle rollovers. The fuel tank is equipped with an on-board refueling vapor recovery (ORVR) system.
The fuel tank, pipes, and hoses should be checked for any road damage which could result in leakage. Also inspect the fuel filler cap for a correct seal and any indications of physical damage.
Fuel Tank (AWD)
1 - Dual Chamber Fuel Tank
2 - Fuel Injectors
3 - Fuel Pressure Regulator
4 - Fuel Filter
5 - Fuel Pump
6 - Primary Fuel Supply Chamber
7 - Fuel Transfer Pump
8 - Secondary Fuel Supply Chamber
The all wheel drive (AWD) fuel tank is manufactured from steel. The fuel tank is located beneath the rear seat area. The tank is held in place with two straps that are secured with bolts. The shape of this tank, called a saddle style tank, was designed to share space with the rear wheel drive shaft. The saddle style tank creates two separate fuel storage areas known as the primary chamber (6) and secondary chamber (8). The primary chamber (6) contains the fuel pump (5), fuel pressure regulator (3) and the fuel filter (4). Also located in the primary chamber is the fuel transfer pump (3). The fuel inlet port on the tank is equipped with an inlet valve. This fuel tank inlet valve prevents the fuel from spewing into the fuel filler neck during aggressive vehicle maneuvers or vehicle rollovers. The fuel tank is equipped with an on-board refueling vapor recovery (ORVR) system.
The fuel tank, pipes, and hoses should be checked for any road damage which could result in leakage. Also inspect the fuel filler cap for a correct seal and any indications of physical damage.
Fuel Tank Filler Neck
In order to prevent refueling with diesel fuel, the fuel filler neck has a built-in restrictor and deflector. The opening of the restrictor admits only the smaller unleaded fuel nozzle. The nozzle must be fully inserted to bypass the deflector. Any attempt at refueling with leaded fuel will result in fuel splashing out of the filler neck.
Fuel Filler Cap
Caution: If a fuel tank filler pipe cap requires replacement, use only a fuel tank filler pipe cap with the same features. Failure to use the correct fuel tank filler pipe cap can result in a serious malfunction of the fuel system.
The fuel filler cap is an updated version of the screw thread design. This latest version of the screw on cap provides only one click with a firm stop, when the cap is correctly installed. Tightening the fuel cap until the one click is heard assures a sealed fuel system. The fuel cap is a pressure-vacuum type operation. To install the cap, turn the cap clockwise until the cap stops and the one click is heard. This indicates that the fuel filler cap gasket (1) is fully seated.
A vacuum relief valve is incorporated into the fuel filler cap. If the pressure in the fuel tank becomes negative (vacuum), the relief valve opens to relieve the pressure created within the fuel tank. Only when the vacuum becomes excessive within the tank does this occur. Vacuum pressure is also vented through the tank pressure control valve which is located on the top of the fuel tank.
A pressure relief valve is also located in the fuel filler cap. The pressure of the fuel vapor within the tank should exceed that for which the fuel system is designed, the pressure relief valve opens, and the excess pressure is vented to the atmosphere.
Fuel Sender Assembly
The fuel sender assembly is located in the fuel tank. The fuel sender assembly contains the electric fuel pump, the fuel level sensor, the fuel pressure regulator, and the fuel filter. Most of the fuel sender assembly components can be serviced separately.
Fuel Sender Assembly-FWD
1 - Fuel Sender Assembly - Upper Support
2 - Spring
3 - Retaining E-Clip
4 - Fuel Pressure Regulator O-rings
5 - Fuel Pressure Regulator
6 - Fuel Pump Strainer
7 - Fuel Sender Assembly - Lower Housing
8 - Fuel Level Sensor
9 - Fuel Pump Jet Tube
10 - Fuel Pump
11 - Fuel Pump O-ring
12 - Fuel Filter and Housing
13 - Fuel Pump Electrical Jumper Harness
Fuel Sender Assembly-AWD
1 - Fuel Tank Pressure (FTP) Sensor
2 - Fuel Sender Assembly Housing - Support
3 - Fuel Level Sensor
4 - Fuel Level Sender Wire Harness
5 - Fuel Pressure Regulator O-ring
6 - Fuel Pressure Regulator
7 - Fuel Pump Strainer
8 - Lower Cushion
9 - Fuel Sender Assembly End Cap - Support
10 - Retaining Clip
11 - Fuel Pump
12 - Fuel Pump O-ring
13 - Fuel Filter and Housing
14 - FTP Sensor Retaining Clip
Fuel Level Sensor
The fuel level sensor is part of the fuel sender assembly. The fuel level sensor (1) consists of a float (2), a float arm, and a variable resistor (1). The fuel level is measured by the position of the float in the fuel tank, and is indicated by a gauge in the instrument panel cluster (IPC) assembly. When the fuel level changes, the float position changes. The change in the float position increases or decreases the resistance reading of the variable resistor. The change in the resistance causes the position of the fuel gauge pointer to change.
The AWD fuel tank with the primary and secondary fuel supply chambers has two fuel level sensors, one for each chamber. The sensor in the secondary chamber sends fuel level information to the sensor in the primary chamber. Together, the two sensors provide the information used by the fuel gauge in the instrument panel (IP).
Fuel Pump
The fuel pump is an electric pump that is controlled by the powertrain control module (PCM) through the circuit opening relay. When the PCM commands the fuel pump to operate, an impeller is driven by an electric motor in the pump assembly, causing the fuel in the tank to be drawn into the fuel pump inlet port. The fuel is then pumped under pressure through the fuel filter and the fuel pressure regulator, out to the fuel feed pipe and hoses to the fuel rail and the fuel injectors. The fuel pressure is maintained when the fuel pump is not running by a pressure control valve located within the pump.
Fuel Transfer Pump
1 - Inlet, pressurized fuel from regulator
2 - Venturi Orifice
3 - Outlet, fuel from regulator and secondary fuel chamber
4 - Fuel Tank Baffle
5 - Secondary Fuel Supply Inlet
6 - Fuel Transfer Pump
The fuel transfer pump (6) is a suction style pump that is used to move fuel from the secondary chamber of the fuel tank to the primary chamber of the fuel tank. Fuel enters the transfer pump (1) under pressure from the fuel pressure regulator. The fuel is forced thru a restriction (2) in the pump creating a venturi effect. At the point of the restriction, a low pressure area is created, which draws fuel into the pump (5) from the secondary chamber. The fuel from the secondary chamber (5) and the fuel from the fuel pressure regulator (1) mix together (3) and flow into a baffled area (4) of the primary chamber.
Fuel Pump Strainer
A fuel pump strainer is attached to the inlet end of the fuel pump and the fuel transfer pump pick-up tube, if equipped. The fuel pump strainer is made of woven plastic. The functions of the fuel pump strainer are to filter contaminants and to wick fuel. The fuel pump strainer is self-cleaning and normally requires no maintenance. Fuel stoppage at this point indicates that the fuel tank contains an abnormal amount of sediment or water. Clean the fuel tank and replace a plugged fuel pump strainer with a new strainer.
Fuel Filter
The fuel filter located in the fuel tank and is part of the fuel sender assembly. The fuel filter housing is constructed to withstand the maximum fuel system pressure, exposure to fuel additives, and changes in temperature. The filter element is made of paper and is designed to trap the particles in the fuel that may cause damage to the fuel injection system.
Fuel Pressure Regulator
The fuel pressure regulator is located in the fuel tank and is part of the fuel sender assembly. The fuel pressure regulator is a diaphragm-operated pressure relief valve consisting of a diaphragm, a spring, and a valve. The fuel pressure regulator is inserted into the fuel sender assembly and sealed with one or more O-rings (1). The fuel pressure regulator used with the composite fuel tank is a double O-ring (3) design, while the regulator in the steel fuel tank uses a single O-ring (2). A correctly calibrated fuel pressure regulator ensures that the fuel is delivered to the fuel injectors at the correct pressure.
Quick Connect Fittings
Quick connect style fuel fittings provide a simplified means of installing and connecting the fuel system components. Depending on the vehicle model, there are 2 types of quick connect fittings. Different types of fittings are used at different locations in the fuel system. Each type of quick connect fitting consists of a unique female connector and a compatible male fuel pipe end. O-rings located inside of the female connector provide a leak proof seal. Integral locking tabs or fingers hold the quick connect fittings together. A special tool is used to service the quick connect fittings.
Fuel Feed Pipes and Hoses
Warning
In order to Reduce the Risk of Fire and Personal Injury:
* If nylon fuel pipes are nicked, scratched or damaged during installation, Do Not attempt to repair the sections of the nylon fuel pipes. Replace them.
* When installing new fuel pipes, Do Not hammer directly on the fuel harness body clips as it may damage the nylon pipes resulting in a possible fuel leak.
* Always cover nylon vapor pipes with a wet towel before using a torch near them. Also, never expose the vehicle to temperatures higher than 115°C (239°F) for more than one hour, or more than 90°C (194°F) for any extended period.
* Before connecting fuel pipe fittings, always apply a few drops of clean engine oil to the male pipe ends. This will ensure proper reconnection and prevent a possible fuel leak. (During normal operation, the O-rings located in the female connector will swell and may prevent proper reconnection if not lubricated.)
The fuel feed and return pipes and hoses carry the fuel from the fuel tank to the fuel injectors. These pipes and hoses are attached to the underbody of the vehicle and should be inspected periodically for kinks or dents that could restrict the fuel flow.