Parking Brake Cable Assembly No. 1

PARKING BRAKE CABLE ASSY NO.1
REPLACEMENT
1. REMOVE FRONT DOOR SCUFF PLATE LH (PEDAL TYPE PARKING BRAKE)
2. REMOVE COWL SIDE TRIM SUB-ASSY LH (PEDAL TYPE PARKING BRAKE)
3. REMOVE INSTRUMENT PANEL SUB-ASSY UPPER (PEDAL TYPE PARKING BRAKE)
4. REMOVE INSTRUMENT PNL INSERT SUB-ASSY LWR LH (PEDAL TYPE PARKING BRAKE)
5. REMOVE CONSOLE PANEL UPPER REAR
6. REMOVE CONSOLE BOX CARPET
7. REMOVE RR CONSOLE BOX
8. REMOVE INSTRUMENT PANEL ASH RECEPTACLE ASSY
9. REMOVE CONSOLE PANEL UPPER
10. REMOVE CONSOLE BOX FRONT
11. REMOVE AIR DUCT REAR NO.1
12. REMOVE AIR DUCT REAR NO.2 REMOVE CONSOLE BOX DUCT NO.1
14. REMOVE SHIFT LEVER SHAFT HOUSING ASSY
15. REMOVE YAWRATE SENSOR (W/ VSC)
16. REMOVE PARKING BRAKE CABLE ASSY NO.1 (PEDAL TYPE PARKING BRAKE)





a. Loosen the turn buckle, disconnect the parking brake cable assy No.1 from the parking brake cable assy No.4.
b. Remove the 2 bolts and console box mounting bracket No.2.





c. Remove the lock nut, adjusting nut, clip and disconnect the parking brake cable assy No. 1 from the parking brake control pedal assy.





d. Remove the 2 nuts, 2 bolts, clip and parking brake cable assy No.1.
17. REMOVE PARKING BRAKE CABLE ASSY NO.1 (LEVER TYPE PARKING BRAKE)





a. Remove the lock nut and adjusting nut from the parking brake cable assy No. 1.
b. Remove the 2 bolts and console box mounting bracket No.2.





c. Remove the 2 bolts and separate the parking brake cable No.1 from the parking brake equalizer.
18. INSTALL PARKING BRAKE CABLE ASSY NO.1 (PEDAL TYPE PARKING BRAKE)





a. Install the parking brake cable assy No.1 with the 2 nuts, 2 bolts and clip.





b. Install the parking brake cable assy No.1 with the clip, adjusting nut and lock nut to the parking brake control pedal assy.
Torque: 5.4 Nm (55 kgf-cm, 48 inch lbs.)
c. Install the console box mounting bracket No.2 with the 2 bolts.
Torque: 12.5 Nm (128 kgf-cm, 9 ft. lbs.)





d. Tighten the turn buckle, connect the parking brake cable assy No. 1 to the parking brake cable assy No.4.
Torque: 5.4 Nm (55 kgf-cm, 48 inch lbs.)
19. INSTALL PARKING BRAKE CABLE ASSY NO.1 (LEVER TYPE PARKING BRAKE)





a. Install the parking brake cable assy No.1 with the 2 bolts to the parking brake equalizer.
Torque: 23 Nm (235 kgf-cm, 17 ft. lbs.)
b. Install the console box mounting bracket No.2 with the 2 bolts.
Torque: 12.5 Nm (128 kgf-cm, 9 ft. lbs.)





c. Install the parking brake cable assy No.1 with the adjusting nut and lock nut to the parking brake lever assy.
Torque: 5.0 Nm (51 kgf-cm, 44 inch lbs.)
20. INSTALL YAWRATE SENSOR (W/ VSC)
21. INSTALL SHIFT LEVER SHAFT HOUSING ASSY
22. INSTALL CONSOLE BOX DUCT NO.1
23. INSTALL AIR DUCT REAR NO.2
24. INSTALL AIR DUCT REAR NO.1
25. INSTALL CONSOLE BOX FRONT
26. INSTALL CONSOLE PANEL UPPER
27. INSTALL INSTRUMENT PANEL ASH RECEPTACLE ASSY
28. INSTALL RR CONSOLE BOX
29. INSTALL CONSOLE BOX CARPET
30. INSTALL CONSOLE PANEL UPPER REAR
31. INSTALL INSTRUMENT PNL INSERT SUB-ASSY LWR LH (PEDAL TYPE PARKING BRAKE)
32. INSTALL INSTRUMENT PANEL SUB-ASSY UPPER (PEDAL TYPE PARKING BRAKE)
33. INSTALL COWL SIDE TRIM SUB-ASSY LH (PEDAL TYPE PARKING BRAKE)
34. INSTALL FRONT DOOR SCUFF PLATE LH (PEDAL TYPE PARKING BRAKE)
35. INSPECT AND ADJUST PARKING BRAKE PEDAL TRAVEL (PEDAL TYPE PARKING BRAKE)
36. INSPECT AND ADJUST PARKING BRAKE LEVER TRAVEL (LEVER TYPE PARKING BRAKE)
37. PERFORM YAWRATE SENSOR ZERO POINT CALIBRATION (W/ VSC)