Diesel Data: Automotive Repair
Home >> Toyota >> 2008 >> Solara Convertible V6-3.3L (3MZ-FE) >> Repair and Diagnosis >> Brakes and Traction Control >> Disc Brake System >> Service and Repair >> Front Brake >> Reassembly

Reassembly








BRAKE: FRONT BRAKE:

REASSEMBLY

1. INSTALL FRONT DISC
(a) Aligning the matchmarks, install the front disc.

HINT: When replacing the disc with a new one, select the installation position where the front disc has the minimum runout.

2. TEMPORARILY TIGHTEN FRONT DISC BRAKE BLEEDER PLUG
(a) Temporarily install the front disc brake bleeder plug to the front disc brake cylinder sub-assembly.
3. INSTALL FRONT DISC BRAKE BLEEDER PLUG CAP
(a) Install the bleeder plug cap to the front disc brake bleeder plug.
4. INSTALL PISTON SEAL
(a) Apply lithium soap base glycol grease to a new piston seal.
(b) Install the piston seal to the front disc brake cylinder sub-assembly.
5. INSTALL FRONT DISC BRAKE PISTON





(a) Apply lithium soap base glycol grease to the front disc brake piston and new cylinder boot.
(b) Install the cylinder boot to the front disc brake piston.
(c) Install the front disc brake piston to the front disc brake cylinder sub-assembly.

NOTE: Do not install the piston forcibly in the front disc brake cylinder sub-assembly.

6. INSTALL CYLINDER BOOT





(a) Install a new cylinder boot to the front disc brake cylinder sub-assembly.

- Install the boot securely to the grooves of the cylinder and piston.
- Do not damage the cylinder boot.

(b) Using a screwdriver, install the set ring.

NOTE: Do not damage the cylinder boot.

7. INSTALL FRONT DISC BRAKE BUSHING DUST BOOT
(a) Hold the front disc brake cylinder mounting in the vise through the soft jaws.
(b) Apply lithium soap base glycol grease to the sealing surface of 2 new front disc brake bushing dust boots. (Components)





(c) Using a socket wrench (19 mm) and hammer, drive the 2 front disc brake bushing dust boots to the front disc brake cylinder mounting.
8. INSTALL FRONT DISC BRAKE CYLINDER SLIDE BUSHING
(a) Apply lithium soap base glycol grease to a new front disc brake cylinder slide bushing. (Components)

(b) Install the cylinder slide bushing to the bottom side of the front disc brake cylinder slide pin (No. 2).
9. INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN





(a) Apply lithium soap base glycol grease to the sliding part and the sealing surface of the front disc brake cylinder slide pin (No. 1) and front disc brake cylinder slide pin (No. 2).
(b) Install the front disc brake cylinder slide pin (No. 1) and front disc brake cylinder slide pin (No. 2) to the front disc brake cylinder mounting.
(c) Install the front disc brake cylinder slide pin (No. 2) to the front disc brake cylinder mounting.
10. INSTALL FRONT DISC BRAKE CYLINDER MOUNTING





(a) Install the front disc brake cylinder mounting with the 2 bolts.
Torque: 107 Nm (1,090 kgf-cm, 79 ft-lbf)
11. INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE
(a) Install the front disc brake pad support plate (No. 1) and front disc brake pad support plate (No. 2) to the front disc brake cylinder mounting.
12. INSTALL FRONT ANTI SQUEAL SHIM
(a) Apply disc brake grease to the front anti squeal shims and install them to each pad. (Components)

NOTICE:
- When replacing worn pads, the anti squeal shims must be replaced together with the pads.
- Install the shims in the correct position and direction.

(b) Install the pad wear indicator plates to the each pad.
13. INSTALL FRONT DISC BRAKE PAD
(a) Install the front disc brake pad to the front disc brake cylinder mounting.

NOTICE:
- There should be no oil or grease on the friction surface of the pads and the disc.
- Brake pads are installed with indicator plates facing upward.

14. INSTALL FRONT DISC BRAKE CYLINDER SUB-ASSEMBLY





(a) Install the front disc brake cylinder sub-assembly with the 2 bolts.
Torque: 34 Nm (350 kgf-cm, 25 ft-lbf)
15. CONNECT FRONT FLEXIBLE HOSE
(a) Install a new gasket and connect the flexible hose with the union bolt.
Torque: 29 Nm (300 kgf-cm, 22 ft-lbf)

NOTE: Install the flexible hose lock securely in the lock hole in the disc brake cylinder.

16. FILL RESERVOIR WITH BRAKE FLUID (Service and Repair)

17. BLEED BRAKE MASTER CYLINDER (Service and Repair)

18. BLEED BRAKE LINE (Service and Repair)

19. BLEED BRAKE ACTUATOR (w/ VSC) (Service and Repair)

20. CHECK FLUID LEVEL IN RESERVOIR (Service and Repair)

21. INSPECT FOR BRAKE FLUID LEAK
22. INSTALL FRONT WHEEL
Torque: 103 Nm (1,050 kgf-cm, 76 ft-lbf)
Diesel-Data.com