Diesel Data: Automotive Repair
Home >> Toyota >> 2009 >> Camry L4-2.4L (2AZ-FXE) Hybrid >> Repair and Diagnosis >> Restraints and Safety Systems >> Seat Belt Systems >> Seat Belt >> Service and Repair >> Rear Seat Inner Belt Assembly >> Installation

Installation








SEAT BELT: REAR SEAT INNER BELT ASSEMBLY: INSTALLATION

INSTALLATION

1. INSTALL REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH





(a) Check the degree of the tilt when the ELR begins to lock.
(1) Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt while gently pulling the belt.
NOTICE: Do not disassemble the retractor.





(b) Align the claw with the seat belt positioning hole and install the rear seat inner with center belt assembly LH with the bolt.
Torque: 42 Nm (428 kgf-cm, 31ft-lbf)
2. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY





(a) Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.
(b) Engage the 4 clips and 5 claws and install the package tray trim panel assembly.
(c) Connect the connector.
3. INSTALL REAR SEAT SHOULDER BELT HOLE COVER





(a) Engage the 4 claws and install the rear seat shoulder belt hole cover.
4. INSTALL REAR SEAT SHOULDER BELT COVER





(a) Engage the 4 claws and install the rear seat shoulder belt cover.
HINT: Use the same procedure for the RH side and LH side.

5. CONNECT REAR SEAT OUTER BELT ASSEMBLY (for LH Side) Installation
6. CONNECT REAR SEAT OUTER BELT ASSEMBLY (for RH Side) Installation
7. INSTALL ROOF SIDE INNER GARNISH LH Installation
8. INSTALL ROOF SIDE INNER GARNISH RH Installation
9. CONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH





(a) Connect the floor end of the rear seat inner with center belt assembly LH with the bolt.
Torque: 42 Nm (428 kgf-cm, 31ft-lbf)
NOTICE: Do not allow the anchor part of the rear seat inner with center belt assembly LH to overlap the protruding parts of the floor panel.

(b) Check if the ELR locks.
NOTICE: The check should be performed with the outer belt assembly installed.
(1) With the belt assembly installed, check that the belt locks when it is pulled out quickly.
10. INSTALL REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH





(a) Install the rear seat inner with center belt assembly RH with the bolt.
Torque: 42 Nm (428 kgf-cm, 31ft-lbf)
NOTICE: Do not allow the anchor part of the rear seat inner with center belt assembly RH to overlap the protruding parts of the floor panel.

11. INSTALL CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH Installation
12. INSTALL CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY RH
HINT: Use the same procedure for the RH side and the LH side.

13. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH Installation
14. INSTALL REAR DOOR SCUFF PLATE LH Installation
15. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH Installation
16. INSTALL REAR DOOR SCUFF PLATE RH Installation
17. INSTALL REAR SIDE SEATBACK ASSEMBLY LH Installation
18. INSTALL REAR SIDE SEATBACK ASSEMBLY RH
HINT: Use the same procedure for the RH side and the LH side.

19. INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY LH Installation
20. INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY RH Installation
21. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY
22. INSTALL REAR SEAT HEADREST ASSEMBLY
23. INSTALL REAR SEAT CUSHION ASSEMBLY Installation
Diesel-Data.com