Diesel Data: Automotive Repair
Home >> Toyota >> 2009 >> Matrix AWD L4-2.4L (2AZ-FE) >> Repair and Diagnosis >> Sensors and Switches >> Sensors and Switches - Brakes and Traction Control >> Wheel Speed Sensor >> Service and Repair >> Rear Speed Sensor >> Removal

Removal








BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: REAR SPEED SENSOR (for 4WD): REMOVAL

REMOVAL
HINT:
- Use the same procedure for RH side and LH side except for the step to remove the rear sensor clip.
- If the sensor rotor needs to be replaced, replace it together with the rear drive shaft assembly.

1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2. REMOVE REAR SEAT CUSHION ASSEMBLY Removal
3. REMOVE REAR SEAT HEADREST ASSEMBLY (for LH Side)
4. REMOVE REAR SEATBACK OUTER HINGE COVER (for LH Side) Removal
5. REMOVE REAR SEATBACK INNER HINGE COVER (for LH Side) Removal
6. REMOVE REAR SEATBACK ASSEMBLY LH Removal
7. REMOVE REAR SEAT HEADREST ASSEMBLY (for RH Side)
8. REMOVE REAR SEAT CENTER HEADREST ASSEMBLY
9. DISCONNECT REAR SEAT CENTER OUTER BELT ASSEMBLY Removal
10. REMOVE REAR SEATBACK OUTER HINGE COVER (for RH Side) Removal
11. REMOVE REAR SEATBACK INNER HINGE COVER (for RH Side) Removal
12. REMOVE REAR SEATBACK ASSEMBLY RH Removal
13. REMOVE REAR DOOR SCUFF PLATE LH (for LH Side) Removal
14. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH (for LH Side) Removal
15. REMOVE REAR DOOR SCUFF PLATE RH (for RH Side) Removal
16. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH (for RH Side) Removal
17. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY (for LH Side) Removal
18. REMOVE REAR SEAT SIDE GARNISH LH (for LH Side) Removal
19. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY (for RH Side) Removal
20. REMOVE REAR SEAT SIDE GARNISH RH (for RH Side) Removal
21. REMOVE REAR WHEEL
22. REMOVE FUEL TANK FILLER PIPE PROTECTOR (for LH Side)





(a) Remove the 3 bolts and fuel tank filler pipe protector.
23. REMOVE REAR SPEED SENSOR LH (for LH Side)
(a) Disconnect the rear speed sensor connector.





(b) Disconnect the grommet of the rear speed sensor wire from the hole in the wheel well.
(c) Remove bolt A and separate the No. 3 sensor clamp.





(d) Disconnect the sensor clip LH from the breather clamp.
(e) Remove bolt B and separate the No. 2 sensor clamp from the suspension member.
(f) Remove the nut and separate the No. 1 sensor clamp from the upper arm.
(g) Remove bolt C and the rear speed sensor body from the rear axle carrier.
NOTE: Keep the sensor tip and rear speed sensor installation hole free of foreign matter.

24. REMOVE REAR SPEED SENSOR RH (for RH Side)
(a) Disconnect the rear speed sensor connector.
(b) Disconnect the grommet of the rear speed sensor wire from the hole in the wheel well.
(c) Remove bolt A and separate the No. 3 sensor clamp.





(d) Disconnect the sensor clip from the breather clamp.
(e) Remove bolt B and separate the No. 2 sensor clamp from the suspension member.
(f) Remove the nut and separate the No. 1 sensor clamp from the upper arm.
(g) Remove bolt C and rear speed sensor body from the rear axle carrier.
NOTE: Keep the sensor tip and rear speed sensor installation hole free of foreign matter.
Diesel-Data.com