Installation

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: REAR SPEED SENSOR (for 2WD): INSTALLATION

INSTALLATION
HINT:
- Use the same procedure for the RH side and LH side.
- The procedure listed below is for the LH side.
- If the sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.

1. INSTALL REAR SPEED SENSOR
(a) Clean the contact surface between the rear axle hub and bearing assembly and a new rear speed sensor.
NOTE: Prevent foreign matter from attaching to the sensor rotor.





(b) Place the rear speed sensor on the rear axle hub and bearing assembly so that the connector is positioned at the bottom when the sensor is installed on the vehicle.





(c) Using SST, steel plates and a press, install a new speed sensor to the rear axle hub and bearing assembly.
SST: 09214-76011

NOTICE:
- Keep the rear speed sensor away from magnets.
- Do not use a hammer to install the rear speed sensor.
- Check that there is no foreign matter such as iron chips on the detecting portion of the rear speed sensor.
- Slowly press the rear speed sensor in straight.

2. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY WITH REAR SPEED SENSOR (for Torsion Beam Type Suspension) Installation
3. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY WITH REAR SPEED SENSOR (for Double Wishbone Type Suspension) Installation
4. INSPECT REAR AXLE HUB BEARING LOOSENESS (for Double Wishbone Type Suspension) Rear Axle Hub (for Double Wishbone Type Suspension)
5. INSPECT REAR AXLE HUB RUNOUT (for Double Wishbone Type Suspension) Rear Axle Hub (for Double Wishbone Type Suspension)
6. INSPECT REAR AXLE HUB BEARING LOOSENESS (for Torsion Beam Type Suspension) Rear Axle Hub (for Torsion Beam Type Suspension)
7. INSPECT REAR AXLE HUB RUNOUT (for Torsion Beam Type Suspension) Rear Axle Hub (for Torsion Beam Type Suspension)
8. INSTALL REAR DISC (for Double Wishbone Type Suspension) Reassembly
9. INSTALL REAR DISC (for Torsion Beam Type Suspension) Installation
10. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY (for Torsion Beam Type Suspension) Replacement
11. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY (for Double Wishbone Type Suspension) Replacement
12. CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY (for Torsion Beam Type Suspension) Installation
13. INSTALL PARKING BRAKE LEVER PROTECTOR (for Torsion Beam Type Suspension) Installation
14. CONNECT REAR SPEED SENSOR WIRE (for Torsion Beam Type Suspension)





(a) Connect the rear speed sensor wire connector to the rear speed sensor.
15. CONNECT REAR SPEED SENSOR WIRE (for Double Wishbone Type Suspension)





(a) Connect the rear speed sensor wire connector to the rear speed sensor.
16. INSPECT PARKING BRAKE LEVER TRAVEL Adjustments
17. ADJUST PARKING BRAKE LEVER TRAVEL (for Torsion Beam Type Suspension) Adjustments
18. INSPECT REAR DISC BRAKE CYLINDER OPERATION LEVER AND STOPPER CLEARANCE (for Torsion Beam Type Suspension) Adjustments
19. ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE LEVER TRAVEL (for Double Wishbone Type Suspension) Adjustments
20. INSTALL REAR WHEEL
Torque: 103 Nm (1050 kgf-cm, 76 ft-lbf)
21. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
22. INSTALL FRONT UPPER CONSOLE BOX (for Torsion Beam Type Suspension) Installation
23. INSPECT BRAKE WARNING LIGHT Diagnosis System
24. CHECK FOR SPEED SENSOR SIGNAL
HINT:
- w/o VSC Test Mode Procedure
- w/ VSC Test Mode Procedure

25. INSPECT AND ADJUST REAR WHEEL ALIGNMENT (for Double Wishbone Type Suspension)
HINT: Rear Wheel Alignment (for Double Wishbone Type Suspension).

26. INSPECT REAR WHEEL ALIGNMENT (for Torsion Beam Type Suspension)
HINT: Rear Wheel Alignment (for Torsion Beam Type Suspension).