Reassembly

SEAT: REAR SEAT ASSEMBLY (for RH Side): REASSEMBLY

REASSEMBLY

1. INSTALL REAR SEAT LEG ASSEMBLY RH





(a) Using a T55 "TORX" socket wrench, install the rear seat leg assembly RH with the 5 "TORX" bolts.
A - Torque: 42 Nm (428 kgf-cm, 31ft-lbf)
B - Torque: 55 Nm (560 kgf-cm, 41ft-lbf)
2. INSTALL REAR CENTER SEATBACK HINGE





(a) Using a T45 "TORX" socket wrench, install the bush and "TORX" bolt.
Torque: 21 Nm (214 kgf-cm, 16ft-lbf)
(b) Install the rear center seatback hinge with the bolt.
Torque: 21 Nm (214 kgf-cm, 16ft-lbf)
3. INSTALL REAR SEAT LEG SIDE COVER LH





(a) Install the rear seat leg side cover LH with the 2 screws.
4. INSTALL REAR SEAT LEG SIDE COVER RH





(a) Install the rear seat leg side cover RH with the 2 screws.
5. INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY RH





(a) Install the 2 bolts.
Torque: 18 Nm (184 kgf-cm, 13ft-lbf)
(b) Using a T45 "TORX" socket wrench, install the rear seat cushion frame sub-assembly RH with the 3 "TORX" bolts and 3 bushes.
Torque: 21 Nm (214 kgf-cm, 16ft-lbf)
6. INSTALL RECLINING ADJUSTER INSIDE COVER LH





(a) Engage the claw and 2 guides.
(b) Install the reclining adjuster inside cover LH with the 2 screws.
7. INSTALL RECLINING ADJUSTER INSIDE COVER RH





(a) Engage the claw and 2 guides.
(b) Install the reclining adjuster inside cover RH with the 2 screws.
8. INSTALL REAR SEAT RECLINING CONTROL CABLE SUB-ASSEMBLY





(a) Engage the claw.
(b) Engage 2 new clamps.
(c) Engage the 4 cable clamps to install the rear seat reclining control cable sub-assembly.
9. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY Installation
10. INSTALL SEPARATE TYPE REAR SEATBACK COVER





(a) Using hog ring pliers, install the separate type rear seatback cover with 10 new hog rings.

Text in Illustration





NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.

11. INSTALL REAR SEATBACK COVER WITH PAD





(a) Using hog ring pliers, install 3 new hog rings.

Text in Illustration





NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.





(b) Using hog ring pliers, install 2 new hog rings.

Text in Illustration





NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.





(c) Engage the hook to install the rear seat cushion cover with pad.
12. INSTALL REAR SEAT CENTER HEADREST SUPPORT RH





(a) Engage the 2 claws to install the rear seat center headrest support RH.
13. INSTALL REAR SEAT CENTER HEADREST SUPPORT LH





(a) Engage the 2 claws to install the rear seat center headrest support LH.
14. INSTALL REAR SEAT HEADREST SUPPORT RH





(a) Engage the 2 claws to install the rear seat headrest support RH.
15. INSTALL REAR SEAT HEADREST SUPPORT LH





(a) Engage the 2 claws to install the rear seat headrest support LH.
16. INSTALL REAR SEAT SHOULDER BELT COVER





(a) Engage the 2 guides and claw, and install the rear seat shoulder belt cover as shown in the illustration.





(b) Engage the 2 guides as shown in the illustration.





(c) Install the rear seatback upper lock bezel with the screw.
17. INSTALL CUP HOLDER





(a) Install the cup holder with the 2 screws.
18. INSTALL REAR SEATBACK HINGE LH





(a) Install the rear seatback hinge LH with the 2 bolts and 2 bushes.
Torque: 6.0 Nm (61 kgf-cm, 53in-lbf)
19. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY





(a) Install the 3 nuts.
Torque: 6.0 Nm (61 kgf-cm, 53in-lbf)





(b) Engage the hook and install the rear seat center armrest assembly.
20. INSTALL CUP HOLDER HOLE COVER





(a) Install the 2 new cup holder hole covers.
21. INSTALL REAR SEATBACK BOARD RH





(a) Engage the 3 guides and 4 clips as shown in the illustration.





(b) Engage the 20 claws and install the rear seatback board RH.
22. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY Installation
23. INSTALL REAR INNER SEAT BELT ASSEMBLY RH Installation
24. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER





(a) Using hog ring pliers, install the separate type rear seat cushion cover with 8 new hog rings.

Text in Illustration





NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.

25. INSTALL REAR SEAT CUSHION COVER WITH PAD





(a) Engage each hook as shown in the illustration.





(b) Engage the 4 hooks.





(c) Using hog ring pliers, install the rear seat cushion cover with pad with a new hog ring.

Text in Illustration





NOTICE:
- Be careful not to damage the cover.
- When installing the hog ring, take care to minimize wrinkles as much as possible.





(d) Engage the hook to install the rear seat cushion with pad.
26. INSTALL REAR SEAT RECLINING COVER RH





(a) Engage the 2 guides.
(b) Install the rear seat reclining cover RH with the 2 screws.
27. INSTALL CENTER SEAT HINGE COVER RH





(a) Disengage the guide as shown in the illustration.
(b) Install the center seat hinge cover RH with the 2 screws.
28. INSTALL REAR SEAT INNER RECLINING COVER RH





(a) Engage the guide.
(b) Install the rear seat inner reclining cover RH with the 2 screws.
29. INSTALL REAR SEAT RECLINING RELEASE LEVER RH





(a) Install the rear seat reclining release lever RH with the 3 screws.
30. INSTALL SEAT ADJUSTER COVER CAP RH





(a) Engage the 3 claws to install the seat adjuster cover cap RH.