Part 2
SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: B1627/82, B1628/82, B1637/82, B1638/82, B1647/82, B1648/82, B1697/82, B1698/82: Lost Communication with Front Passenger Side - Side Airbag Sensor Assembly
DTC B1627/82 - Lost Communication with Front Passenger Side - Side Airbag Sensor Assembly
DTC B1628/82 - Front Passenger Side - Side Airbag Sensor Assembly Initialization Incomplete
DTC B1637/82 - Lost Communication with Passenger Side Rear Airbag Sensor
DTC B1638/82 - Passenger Side Rear Airbag Sensor Initialization Incomplete
DTC B1647/82 - Lost Communication with Front Passenger Side Satellite Sensor Bus
DTC B1648/82 - Front Passenger Side Satellite Sensor Bus Initialization Incomplete
DTC B1697/82 - Lost Communication with Passenger Side Door Side Airbag Sensor
DTC B1698/82 - Passenger Side Door Side Airbag Sensor Initialization Incomplete
Part 2
Continued
14. CHECK WIRE HARNESS (SHORT TO B+)
(a) Connect the cable to the negative (-) battery terminal.
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Text in Illustration
NG -- CHECK FRONT DOOR WIRE RH (SHORT TO B+)
OK -- Continue to next step.
15. CHECK WIRE HARNESS (SHORT TO GROUND)
(a) Turn the ignition switch off.
(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
NG -- CHECK FRONT DOOR WIRE RH (SHORT TO GROUND)
OK -- Continue to next step.
16. CHECK SIDE AIRBAG SENSOR RH (FOR REAR SIDE)
(a) Connect the connectors to the rear airbag sensor RH, side airbag sensor RH (for front side) and center airbag sensor assembly.
(b) Interchange the side airbag sensor LH (for rear side) with side airbag sensor RH (for rear side) and connect the connectors.
(c) Connect the cable to the negative (-) battery terminal.
(d) Turn the ignition switch to ON, and wait for at least 60 seconds.
(e) Clear the DTCs stored in the memory DTC Check / Clear.
(f) Turn the ignition switch off.
(g) Turn the ignition switch to ON, and wait for at least 60 seconds.
(h) Check for DTCs DTC Check / Clear.
Result:
Text in Illustration
HINT: Codes other than DTC B1642, B1643, or 81 and B1647, B1648, or 82 may be output at this time, but they are not related to this check.
C -- USE SIMULATION METHOD TO CHECK
B -- REPLACE SIDE AIRBAG SENSOR RH (FOR REAR SIDE)
A -- Continue to next step.
17. CHECK REAR AIRBAG SENSOR RH
(a) Turn the ignition switch off.
(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(c) Return the side airbag sensor LH (for rear side) and side airbag sensor RH (for rear side) to their original positions and connect the connectors.
(d) Interchange the rear airbag sensor LH with RH and connect the connectors to them.
(e) Connect the cable to the negative (-) battery terminal.
(f) Turn the ignition switch to ON, and wait for at least 60 seconds.
(g) Clear the DTCs stored in the memory DTC Check / Clear.
(h) Turn the ignition switch off.
(i) Turn the ignition switch to ON, and wait for at least 60 seconds.
(j) Check for DTCs DTC Check / Clear.
Result:
Text in Illustration
HINT: Codes other than DTC B1642, B1643, or 81 and B1647, B1648, or 82 may be output at this time, but they are not related to this check.
C -- USE SIMULATION METHOD TO CHECK
B -- REPLACE REAR AIRBAG SENSOR RH
A -- Continue to next step.
18. CHECK SIDE AIRBAG SENSOR RH (FOR FRONT SIDE)
(a) Turn the ignition switch off.
(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(c) Return the rear airbag sensor LH and RH to their original positions and connect the connectors.
(d) Interchange the side airbag sensor LH (for front side) with side airbag sensor RH (for front side) and connect the connectors.
(e) Connect the cable to the negative (-) battery terminal.
(f) Turn the ignition switch to ON, and wait for at least 60 seconds.
(g) Clear the DTCs stored in the memory DTC Check / Clear.
(h) Turn the ignition switch off.
(i) Turn the ignition switch to ON, and wait for at least 60 seconds.
(j) Check for DTCs DTC Check / Clear.
Result:
Text in Illustration
HINT: Codes other than DTC B1642, B1643, or 81 and B1647, B1648, or 82 may be output at this time, but they are not related to this check.
C -- USE SIMULATION METHOD TO CHECK
B -- REPLACE SIDE AIRBAG SENSOR RH (FOR FRONT SIDE)
A -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY
19. CHECK FRONT DOOR WIRE RH (OPEN)
(a) Disconnect the front door wire RH connector from the No. 2 floor wire.
HINT: SST has already been inserted into connector E.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
NG -- REPLACE FRONT DOOR WIRE RH
OK -- REPLACE NO. 2 FLOOR WIRE
20. CHECK FRONT DOOR WIRE RH (SHORT)
(a) Disconnect the front door wire RH connector from the No. 2 floor wire.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
NG -- REPLACE FRONT DOOR WIRE RH
OK -- REPLACE NO. 2 FLOOR WIRE
21. CHECK FRONT DOOR WIRE RH (SHORT TO B+)
(a) Turn the ignition switch off.
(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(c) Disconnect the front door wire RH connector from the No. 2 floor wire.
(d) Connect the cable to the negative (-) battery terminal.
(e) Turn the ignition switch to ON.
(f) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Text in Illustration
NG -- REPLACE FRONT DOOR WIRE RH
OK -- REPLACE NO. 2 FLOOR WIRE
22. CHECK FRONT DOOR WIRE RH (SHORT TO GROUND)
(a) Disconnect the front door wire RH connector from the No. 2 floor wire.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
NG -- REPLACE FRONT DOOR WIRE RH
OK -- REPLACE NO. 2 FLOOR WIRE
23. CHECK PAST DTC
(a) Turn the ignition switch to ON, and wait for at least 60 seconds.
(b) Check the past DTCs DTC Check / Clear.
Result:
HINT: Codes other than past DTC B1627 and B1637 may be output at this time, but they are not related to this check.
C -- CHECK REAR AIRBAG SENSOR RH
B -- CHECK SIDE AIRBAG SENSOR RH (FOR REAR SIDE)
A -- Continue to next step.
24. CHECK PRESENT DTC
(a) Turn the ignition switch to ON, and wait for at least 60 seconds.
(b) Check the present DTCs DTC Check / Clear.
Result:
HINT: Codes other than present DTC B1628 and B1638 may be output at this time, but they are not related to this check.
B -- CHECK CONNECTORS
A -- Continue to next step.
25. CHECK CONNECTORS
(a) Turn the ignition switch off.
(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(c) Check that the connectors are properly connected to the center airbag sensor assembly, side airbag sensor RH (for rear side) and rear airbag sensor RH.
OK:
The connectors are properly connected.
HINT: If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.
(d) Disconnect the connectors from the center airbag sensor assembly, side airbag sensor RH (for rear side) and rear airbag sensor RH.
(e) Check that the terminals of connectors are not damaged.
OK:
The terminals are not deformed or damaged.
NG -- REPLACE NO. 2 FLOOR WIRE
OK -- Continue to next step.
26. CHECK NO. 2 FLOOR WIRE (OPEN)
(a) Using SST, connect terminals 8 (BBP+) and 11 (BBP-) of connector B.
NOTICE: Do not forcibly insert SST into the terminals of the connector when connecting.
SST: 09843-18040
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
NG -- REPLACE NO. 2 FLOOR WIRE
OK -- Continue to next step.
27. CHECK NO. 2 FLOOR WIRE (SHORT)
(a) Disconnect SST from connector B.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
NG -- REPLACE NO. 2 FLOOR WIRE
OK -- Continue to next step.
28. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)
(a) Connect the cable to the negative (-) battery terminal.
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Text in Illustration
NG -- REPLACE NO. 2 FLOOR WIRE
OK -- Continue to next step.
29. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)
(a) Turn the ignition switch off.
(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
NG -- REPLACE NO. 2 FLOOR WIRE
OK -- Continue to next step.
Continued in Part 3 Part 3