Part One
NETWORKING: CAN COMMUNICATION SYSTEM: Check CAN Bus Lines for Short Circuit
- Check CAN Bus Lines for Short Circuit
DESCRIPTION
There may be a short circuit in the CAN main wire and/or CAN branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ohms.
*1: w/ Network gateway ECU
*2: w/o Network gateway ECU
WIRING DIAGRAM
INSPECTION PROCEDURE
NOTICE:
* Turn the ignition switch off before measuring the resistance of CAN bus main wires and the CAN bus branch wires.
* After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
* Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check the connectors, open the doors and leave them open.
HINT
* Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
* Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below will help determine the cause of the malfunction.
PROCEDURE
1. CHECK FOR SHORT IN CAN BUS WIRES (DLC3 BRANCH WIRE)
(a) Turn the ignition switch off.
(b) Disconnect the CAN No. 1 junction connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
NG -- REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3
OK -- Continue to next step.
2. CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 2 JUNCTION CONNECTOR)
(a) Reconnect the CAN No. 1 junction connector.
(b) Disconnect the CAN No. 2 junction connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
NG -- CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 1 JUNCTION CONNECTOR - CAN NO. 2 JUNCTION CONNECTOR)
OK -- Continue to next step.
3. CHECK FOR SHORT IN CAN BUS WIRES (ECM MAIN WIRE)
(a) Measure the resistance according to the value(s) in the table below.
HINT
The resistance must be measured after the CAN No. 2 junction connector is disconnected.
Standard Resistance:
NG -- CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 2 JUNCTION CONNECTOR - ECM)
OK -- Continue to next step.
4. CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 2 JUNCTION CONNECTOR - SKID CONTROL ECU)
(a) Disconnect the skid control ECU connector.
(b) Measure the resistance according to the value(s) in the table below.
HINT
The resistance must be measured after the CAN No. 2 junction connector is disconnected.
Standard Resistance:
NG -- REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - SKID CONTROL ECU)
OK -- Continue to next step.
5. CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)
(a) Reconnect the CAN No. 2 junction connector.
(b) Measure the resistance according to the value(s) in the table below.
HINT
* The resistance must be measured after the CAN No. 1 and CAN No. 2 junction connector are reconnected.
* The resistance must be measured after the skid control ECU connector is disconnected.
Standard Resistance:
Result:
C -- REPLACE JUNCTION CONNECTOR (CAN No. 2)
B -- REPLACE BRAKE ACTUATOR ASSEMBLY Removal
A -- REPLACE BRAKE ACTUATOR ASSEMBLY Removal
6. CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 2 JUNCTION CONNECTOR - ECM)
(a) Disconnect the ECM connector.
(b) Measure the resistance according to the value(s) in the table below.
HINT
The resistance must be measured after the CAN No. 2 junction connector is disconnected.
Standard Resistance:
Result:
C -- REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - ECM)
B -- REPLACE ECM Removal
A -- REPLACE ECM Removal
7. CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 1 JUNCTION CONNECTOR - CAN NO. 2 JUNCTION CONNECTOR)
(a) Turn the ignition switch off.
(b) Disconnect the CAN No. 1 junction connector.
(c) Measure the resistance according to the value(s) in the table below.
HINT
The resistance must be measured after the CAN No. 2 junction connector is disconnected.
Standard Resistance:
NG -- REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN NO. 1 JUNCTION CONNECTOR - CAN NO. 2 JUNCTION CONNECTOR)
OK -- Continue to next step.
8. CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 1 JUNCTION CONNECTOR - COMBINATION METER)
(a) Measure the resistance according to the value(s) in the table below.
HINT
The resistance must be measured after the CAN No. 1 junction connector is disconnected.
Standard Resistance:
NG -- CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER MAIN WIRE)
OK -- Continue to next step.
9. CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 1 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
NOTICE:
For vehicles without the network gateway ECU, go to "CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 1 JUNCTION CONNECTOR - 4WD CONTROL ECU)".
(a) Disconnect the network gateway ECU connector.
(b) Measure the resistance according to the value(s) in the table below.
HINT
The resistance must be measured after the CAN No. 1 junction connector is disconnected.
Standard Resistance:
NG -- REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (CAN NO. 1 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
OK -- Continue to next step.
10. CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 1 JUNCTION CONNECTOR - 4WD CONTROL ECU)
(a) Disconnect the 4WD control ECU connector.
(b) Measure the resistance according to the value(s) in the table below.
HINT
The resistance must be measured after the CAN No. 1 junction connector is disconnected.
Standard Resistance:
NG -- REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (CAN NO. 1 JUNCTION CONNECTOR - 4WD CONTROL ECU)
OK -- Continue to next step.
11. CHECK FOR SHORT IN CAN BUS WIRES (CAN NO. 1 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)
(a) Disconnect the steering angle sensor connector.
(b) Measure the resistance according to the value(s) in the table below.
HINT
The resistance must be measured after the CAN No. 1 junction connector is disconnected.
Standard Resistance:
NG -- REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (CAN NO. 1 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)
OK -- Continue to next step.