Installation

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: REAR SPEED SENSOR (for 2WD): INSTALLATION

HINT
* Use the same procedure for the RH side and LH side.
* The procedure listed below is for the LH side.
* If the sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.
* The rear speed sensor is a component of the rear axle hub and bearing assembly with rear speed sensor. If the sensor malfunctions, replace the rear axle hub and bearing assembly with rear speed sensor.

1. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY WITH REAR SPEED SENSOR (for Torsion Beam Type Suspension)

(a) Install the rear axle hub and bearing assembly with rear speed sensor Installation.

HINT
* If the sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.
* The rear speed sensor is a component of the rear axle hub and bearing assembly with rear speed sensor. If the sensor malfunctions, replace the rear axle hub and bearing assembly with rear speed sensor.

2. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY WITH REAR SPEED SENSOR (for Double Wishbone Type Suspension)

(a) Install the rear axle hub and bearing assembly with rear speed sensor Installation.

HINT
* If the sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.
* The rear speed sensor is a component of the rear axle hub and bearing assembly with rear speed sensor. If the sensor malfunctions, replace the rear axle hub and bearing assembly with rear speed sensor.

3. INSPECT REAR AXLE HUB BEARING LOOSENESS (for Double Wishbone Type Suspension) Rear Axle Hub (for Double Wishbone Type Suspension)

4. INSPECT REAR AXLE HUB RUNOUT (for Double Wishbone Type Suspension) Rear Axle Hub (for Double Wishbone Type Suspension)

5. INSPECT REAR AXLE HUB BEARING LOOSENESS (for Torsion Beam Type Suspension) Rear Axle Hub (for Torsion Beam Type Suspension)

6. INSPECT REAR AXLE HUB RUNOUT (for Torsion Beam Type Suspension) Rear Axle Hub (for Torsion Beam Type Suspension)

7. INSTALL REAR DISC (for Double Wishbone Type Suspension) Reassembly

8. INSTALL REAR DISC (for Torsion Beam Type Suspension) Reassembly

9. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY (for Torsion Beam Type Suspension) Replacement

10. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY (for Double Wishbone Type Suspension) Replacement

11. CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY (for Torsion Beam Type Suspension) Installation

12. INSTALL PARKING BRAKE LEVER PROTECTOR (for Torsion Beam Type Suspension) Installation

13. CONNECT REAR SPEED SENSOR WIRE (for Torsion Beam Type Suspension)

(a) Connect the rear speed sensor wire connector to the rear speed sensor.





14. CONNECT REAR SPEED SENSOR WIRE (for Double Wishbone Type Suspension)

(a) Connect the rear speed sensor wire connector to the rear speed sensor.





15. INSPECT PARKING BRAKE LEVER TRAVEL Adjustments

16. ADJUST PARKING BRAKE LEVER TRAVEL (for Torsion Beam Type Suspension) Adjustments

17. INSPECT REAR DISC BRAKE CYLINDER OPERATION LEVER AND STOPPER CLEARANCE (for Torsion Beam Type Suspension) Adjustments

18. ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE LEVER TRAVEL (for Double Wishbone Type Suspension) Adjustments

19. INSTALL REAR WHEEL

Torque : 103 Nm (1050 kgf-cm, 76 ft-lbf)

20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

21. INSTALL FRONT UPPER CONSOLE BOX (for Torsion Beam Type Suspension) Installation

22. INSPECT BRAKE WARNING LIGHT

* for 2ZR-FE: Test Mode Procedure

* for 2AZ-FE: Test Mode Procedure

23. CHECK FOR SPEED SENSOR SIGNAL

* for 2ZR-FE: Test Mode Procedure

* for 2AZ-FE: Test Mode Procedure

24. INSPECT AND ADJUST REAR WHEEL ALIGNMENT (for Double Wishbone Type Suspension)

HINT
Rear Wheel Alignment (for Double Wishbone Type Suspension).

25. INSPECT REAR WHEEL ALIGNMENT (for Torsion Beam Type Suspension)

HINT
Testing and Inspection.