Part 2

- Take the new inner handle from the kit and press it onto the boot lid.
- Refit the warning triangle holder and the warning triangle on the boot lid.

Installing the parking assistance camera (PAC)





- Take the control module from the kit.
- Clean the two polished surfaces on the control module using isopropanol.
- Wipe dry.





- Take two Velcro strips from the kit and cut them in the middle to create four equal parts.

Steps 47-53 apply to cars without a TRM module.




- Press the Velcro strips two and two.





- Remove the protective film from one side of the two attached Velcro strips.





- Press the Velcro strips onto the cleaned surfaces of the control module.





- Clean the surfaces under the tail lights with isopropanol. Wipe dry.


Note! The adapter cable A was included in a previous version of the kit for the parking camera.The adapter cable B was included in a later version of the kit for the parking camera.Both versions are suitable for all cars.

Illustration A




- Connect the previously routed cable harness connector (1) to the right-hand connector on the control module.
- Take the adapter cable A/B from the kit and connect the large green connector to the socket on the control module, as illustrated.
- Connect the connector (2) on the pre-routed, taped cable harness for the power supply under the left-hand tail lamp, to the corresponding connector on the adapter cable.
- Take the long remaining cable harness from the kit and connect the end with the gray connector (3) to the connector in the middle of the control module.
- Clamp the adapter cable's remaining connector using the tie strap from the kit.

Figure B shows adapter cable A





Figure C shows adapter cable B









- Remove the protective film from the installed Velcro strips.





- Press the control module upwards firmly as high as possible on the flat surface under the tail lamp, according to the measurements illustrated.

Steps 54-69 apply to cars with a TRM module.




- Remove the two connectors from the top of the TRM module.
- Remove the TRM module from the Velcro strips on the plate under the rear lamp and place to one side.





- Allow the old Velcro strips to remain in the body.





- Remove the protective film from the Velcro strips.





- Press the Velcro strips on to the cleaned surfaces on the parking assistance camera (PAC).


Note! The adapter cable A was included in a previous version of the kit for the parking camera.The adapter cable B was included in a later version of the kit for the parking camera.Both versions are suitable for all cars.

Figure A shows adapter cable A





Figure B shows adapter cable B




- Connect the previously routed cable harness connector to the right-hand connector on the control module (1).
- Take the adapter cable A/B from the kit and connect the large green connector to the socket on the control module, as illustrated.
- Connect the connector (2) on the pre-routed cable harness for the power supply to the corresponding contact on the adapter cable.
- Take the long remaining cable harness from the kit and connect the end with the gray connector (3) to the connector in the middle of the control module.





- Press the control module firmly onto the existing Velcro straps under the tail lamp.





- Clean the marked surfaces on the control module with isopropanol. Wipe dry.





- Remove the marked Velcro strip from the TRM module.





- Take two Velcro strips from the kit and cut them in the middle to create four equal parts.





- Clean the marked surfaces on the TRM module with isopropanol. Wipe dry.





- Remove the protective film from one of the Velcro strips.





- Press the Velcro strip on to the TRM module beside the other strip , as illustrated.





- Press the two Velcro strips onto the TRM module's two existing Velcro strips.





- Remove the protective film from the Velcro strips.





- Press the TRM module onto the control module securely, as illustrated.





- Connect the remaining green connector (1) on the adapter cable for the power supply to the corresponding socket in the TRM module.
- Connect the remaining gray connector (2), which was removed from the TRM module.

Steps 70-71 only apply to cars with adapter cable B for the power supply




- Route the long ground lead in the adapter cable to the right-hand side of the rear harness.
- Connect the cable to the lower of the ground screws and tighten the screw with 10 Nm (7.5 lbf.ft.)





- Wash the rear crossmember using isopropanol where the ground lead is to be taped. Wipe dry.
- Secure the cable using a wide piece of silver/fabric tape or similar.

Note! The ground lead must only be taped at the rear crossmember, it must not be secured by the thick cable harness.

Applies to all models

Illustration A




- Route the previously connected cable harness inside the insulation panel at the left-hand rear wheel arch and out through the hole in the body.
- Take a tie strap from the kit and secure the cable at the fuse holder's cable harness.

Illustration B




- Pull out the B post panel at the lower edge until the two clips release.
- Continue to route the cable harness inside the B post panel and forwards in the car. Route the cable harness along the left-hand side, in front of the floor and insulation panels, up to the front edge of the door opening.

Illustration C




- Route the cable harness inside the floor and insulation panels, up on the A post slightly, and then at an angle upwards, in through the lower hole behind the end panel, towards the dashboard. Route the cable harness to the location for the screen in the dashboard.
- Place the cable harness so that it does not come into contact with sharp edges or moving parts under the dashboard.