Part 3

Applies to right-hand drive cars
- Take a piece of wire and insert it by the air ducts through the hole for the screen. Pull it out to the left, above the glove compartment and out through the left-hand end of the dashboard.
- Tape the connector on the cable to the screen by the wire.
- Pull the cable up to the location for the screen and out through the hole in the dashboard.


Illustration A





Applies to all models
- Tape the cable using foam or insulation tape for example, at the point where the cable lies against the edge. This is to protect it against rubbing.
- Take a tie strap from the kit and secure the cable in the hole on the end as illustrated.

Illustration B





Applies to left-hand drive cars
- Take two tie straps from the kit and clamp the cable at the existing cable harnesses inside the dashboard as illustrated.






Applies to all models
- Take the screen with bracket.
- Connect the connector (1) on the pre-routed cable to the left-hand socket on the screen.
- Reinstall the connector (2) for the existing cable in the right-hand socket on the screen.
- Reinstall the bracket with the screen and tighten using the six screws.





- Reinstall the loudspeaker grille.

Finishing work

Steps 77-78 apply to left-hand drive cars




- Connect and reinstall the combined instrument panel.


Illustration A




- Reinstall the panel with the steering column cover's rubber seal and press the eight clips into place.

Illustration B




- Press the panel in front of the steering column cover.

Applies to all models




- Reinstall the lower panel of the B post panel.





- Reinstall the A post's lower panel.





- Reinstall the rubber strip in the door opening.





- Reinstall the front door's sill trim panel.





- Reinstall the dashboard end.





- Connect the cargo compartment lighting connector.
- Reinstall the side panel in the cargo compartment.
- Reinstall the four plastic nuts at the lower edge and the three clips at the upper edge.
- Repeat for the other side.





- Reinstall the sill trim panel in the door opening for the left-hand rear door.





- Reinstall the side bolster by first hooking it at the lower mounting, and then pressing it in at the upper edge until it locks securely.
- Insert the seatbelt in the guide on the side bolster.
- Fold up the backrest.





- Connect the connectors for seat heating underneath, on both sides.
- Press the seat cushion into place.





- Reinstall the sill trim panel in the cargo compartment by first pressing it into the clips at the upper edge (1) and then the clips on the inside (2).





- Reinstall the rubber strip in the cargo compartment opening.





- Reinstall the cargo compartment carpet.





- Reconnect the battery negative lead






Warning! When the ignition is to be switched on for the first time after the battery has been disconnected, this must be done whilst by standing outside the vehicle, stretching your arm in and avoiding the working area for the airbags.

- Set the ignition switch to position II.





- Download software (application) for the accessory's function.






Perform a function test as follows.
- Engage reverse gear.
- Activate the screen for RTI.
- Wait for the message "Update Environment" to appear on the screen.
- Follow the on-screen instructions.
- Switch off the ignition for at least 10 seconds.
- Turn the ignition on.
- Activate the screen for RTI.
- Check that the support lines appear on the screen and that these react to steering wheel movements.

Applies to cars with chassis number 0-47999
Download the software from the DVD (purchased separately):
1. Connect the battery charger if the battery voltage is less than 12V.
2. Turn on the ignition (push and hold the starter button).
3. Start NAVI.
4. Insert the disc in the navigation system's DVD player, after which the installation starts.
5. Press ENTER when asked:
1. "New SW found
current SW: v0855
new SW: v0856
continue"
1. The download takes about 10 minutes and is completed with the following message.
"The disc in the DVD player can not be read. Please check the disc. If this happens again please have the system inspected at your nearest workshop."
2. Reinsert the map disc.
3. Check that the download was successful.
- Press BACK
Select "Settings"
Select "System options"
Select "About"
SW version should be 0856 or later.

Note! If the car already has the latest software installed the following text is displayed:"The disc in the DVD player can not be read. Please check the disc. If this happens again please have the system inspected at your nearest workshop."