Diesel Data: Automotive Repair
Home >> Volvo >> 2011 >> C30 T5 L5-2.5L Turbo VIN 67 B5254T7 >> Repair and Diagnosis >> Sensors and Switches >> Sensors and Switches - Accessories and Optional Equipment >> Parking Assist Distance Sensor >> Service and Repair >> Parking Assistance, Front >> Part 2

Part 2












Parking assistance, front



















































INTRODUCTION
- NOTE! Read through the whole installation instruction before starting the work.
- The illustrations display the procedure in order of operation. The order of operation is repeated in the text






Parking assistance, front





- Raise the car.
- Cut out a hole in the heat insulation that is approx. 20 mm (25/32".) larger than the size of the rubber grommet.





- Take the rubber grommet from the kit and cut the top off the smaller rubber nipples
- Lubricate the rubber grommet. Use low temperature grease (P/N 1161417).
- Thread the rubber grommet on the cable harness.
- Route the cable harness in through the hole and press the rubber grommet into the hole so that it seals properly.
- Pull the cable harness so that the correct length remains in the engine compartment.
- Make sure that the heating hose for the cable harness is in contact against the rubber grommet and secure it with a tie strap.





- Lower the car.
- Release the catch on the connector that was taped.
- Connect the pre-routed cable harness terminals in the connector as follows.
1. 1 Blue (BL)
2. 2 Green (GN)
3. 3 Violet (VO)
4. 4 Yellow (Y)
5. 5 White (W)
6. 6 Black (SB)
- Press back the connector's catch.





- Take the long cable harness from the kit. Connect it to the connector which has just been prepared.
- Route the cable harness from the lower edge of the A pillar and further back at the sill and under the carpet.
- Fold back the carpet and screw the clip into place.






Note! Applies to left-hand drive cars

- Route the cable harness further back and under the seat support and backwards and into the cargo compartment, along the existing cable harnesses.
- Position the cable harness so that it does not get trapped or damaged.






Note! Applies to right-hand drive cars

- Route the cable harness from the lower edge of the A pillar and further back under the carpet and behind the large side panel.






Note! Applies to right-hand drive cars

- Route the cable harness under the floor's insulation panel over to the right-hand side.





- Route the cable further along the existing cable harnesses backwards and into the cargo compartment, to the right rear corner of the cargo floor support.
- Position the cable so that is does not get trapped or damaged.





- Lift up the right-hand side cargo floor support.
- Locate the parking assistance module (PAM). It is secured on the right-hand side of the cargo compartment floor, under the cargo floor support.






Note! Ensure that the connector's catch clicks and is securely positioned.

- Connect the pre-routed cable to the vacant connection (middle) on the parking assistance module (PAM).





- Remove the protective film from one side of the double-backed tape.
- Secure the tape on the holder.





- Remove the remaining protective film on the holder.
- Install the centering tool in the holder according to the image.






Note! The holders must be mounted turned against the holes as illustrated. The holders must also be horizontal and in line with the bumper cover.

- Press in the holder on the bumper cover.
- Repeat the steps 49-51 for the other holders.






Note! On left-hand drive cars, the large gray connector must be on the right-hand side. On right-hand drive cars the large gray connector must be on the left-hand side. (see point 54).

- Connect the cable harness connectors to the sensors.
- Install the sensors in their holders.





- Secure the end of the cable harness at the sensors to the bumper cover using butyl tape.






Note! On left-hand drive cars the large gray connector must be on the right-hand side. On right-hand drive cars it must be on the left-hand side.

- Secure the cable harness to the bumper cover using butyl tape in the locations illustrated.





- Hold the bumper up against the car and connect the connector for the sensor cable to the connector at the car.
- Secure the assembled connector on the member (1). Use a tie strap on each side of the connector.
- Connect the connectors to any fog lamps.
- Slide the bumper cover into the correct position





- Guide the lower edge of the bumper cover into the guides.
- Reinstall the bumper cover by repeating points 5 - 8 in reverse order.
- Reinstall the engine splash guard.





- Reinstall the side panel.
- Reinstall the clip for the cargo floor support.
- Reinstall the weatherstrip.
- Reinstall the sill trim panel.






Note! There are eleven clips on the reverse of the panel that must all engage in the body. Take care when aligning so that the clips do not break. Broken clips must be replaced with new ones.

- Reinstall the side panel, ensure that all clips engage.
- Tighten the panel using existing screws.





- The image shows the location of the clips on the rear of the panel.





- Remove the 2 parts of the cut-off safety clip.
- Take a new safety clip from the kit, press it together and install it on the B pillar panel.
- Reinstall the panel and weatherstrip.





- Reinstall the rear sill trim panel, the 2 guides must be in the corresponding cut-outs in the side panel.
- Reinstall the front sill trim panel.
- Reinstall the backrest. Tighten the screws to 25 Nm (18.5 lbf.ft.).
- Reinstall the arm rest.
- Reinstall the seat cushion.





- Download the software for the accessory's function following the service information in VIDA.

Diesel-Data.com