Oil Pan: Service and Repair
Oil Pan
Removal
1. With the vehicle in NEUTRAL position it on a hoist.
2. Remove the battery tray.
3. Detach the 2 positive battery cable pin-type retainers and position aside.
4. Detach the transmission connector wire harness pin-type retainer and position aside.
5. Remove the nut from the heated oxygen sensor (HO2S) and catalyst monitor sensor wire connector bracket.
6. Remove the nut and position the HO2S and catalyst monitor sensor wire connector bracket aside.
7. CAUTION: To prevent damage to the transmission, do not loosen the transmission-to-engine bolts more than 5 mm (0.19 in).
- Loosen the upper belihousing-to-engine bolt and stud bolt 5 mm (0.19 in).
8. Remove the oil level indicator and tube.
9. NOTE: Automatic transmission shown manual transmission similar.
- Loosen the 2 (automatic transmission) or 3 (manual transmission) front lower bellhousing-to-engine bolts 5 mm (0.19 in).
10. Loosen the rear lower engine-to-belihousing bolt and stud bolt 5 mm (0.19 in).
11. Remove the 2 bellhousing-to-oil pan bolts and the 2 oil pan bolts.
12. Remove the 2 oil pan-to-bellhousing bolts.
13. Slide the transmission rearward 5 mm (0.19 in).
14. Remove the 2 bolts and the accessory drive belt splash shield.
15. Drain the engine oil.
- Install the drain plug.
- To install tighten to 28 Nm (21 lb-ft).
16. Remove the 4 engine front cover-to-oil pan bolts.
17. Remove the 11 bolts and the oil pan.
Installation
1. CAUTION: Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means to clean the sealing surfaces. These tools cause scratches and gouges, which make leak paths. Use a plastic scraping tool to remove traces of sealant.
- Clean and inspect all mating surfaces.
2. NOTE: If the oil pan is not secured within 10 minutes of sealant application the sealant must be removed and the sealing area cleaned with metal surface cleaner.
- Allow to dry until there is no sign of wetness or 10 minutes whichever is longer. Failure to follow this procedure can cause future oil leakage.
- Apply a 2.5 mm (0.09 in) bead of silicone gasket and sealant to the oil pan-to- engine block and to the oil pan-to-engine front cover mating surface.
3. Position the oil pan onto the engine and install the oil pan bolts finger-tight.
4. CAUTION: The engine front cover-to-oil pan bolts must be tighten first to align the front surface of the oil pan flush with the front surface of the engine block.
- Install the 4 engine front cover-to-oil pan bolts. Tighten to 10 Nm (89 lb-in).
5. Tighten the oil pan bolts in the sequence shown.
- Tighten to 25 Nm (18 lb-ft).
6. Install the accessory drive belt splash shield and the 2 bolts.
- Tighten to 9 Nm (80 lb-in).
7. Alternate tightening the 1 front belihousing-to-engine and 1 rear engine-tobelihousing lower bolts to slide the transmission and engine together.
- Tighten to 48 Nm (35 lb-ft).
8. NOTE: Automatic transmission shown~ manual transmission similar.
- Tighten the remaining 1 (automatic transmission) or 2 (manual transmission) lower front bellhousing-to-engine bolt(s).
- Tighten to 48 Nm (35 lb-ft).
9. Tighten the remaining 1 rear engine-to-belihousing stud bolt.
- Tighten to 48 Nm (35 lb-ft).
10. Install the 2 bellhousing-to-oil pan bolts.
- Tighten to 48 Nm (35 lb-ft).
11. Install the 2 oil pan-to-belihousing bolts.
- Tighten to 48 Nm (35 lb-ft).
12. Install the oil level indicator and tube.
13. Tighten the top bellhousing-to-engine bolt and stud bolt.
- Tighten to 48 Nm (35 lb-ft).
14. Position the HO2S and catalyst monitor sensor wire connector bracket and install the nut.
- Tighten to 25 Nm (18 lb-ft).
15. Install the HO2S and catalyst monitor sensor wire connector bracket nut.
- Tighten to 25 Nm (18 lb-ft).
16. Position and attach the transmission connector wire harness pin-type retainer.
17. Position and attach the 2 positive battery cable pin-type retainers.
18. Install the battery tray.
19. Fill the engine with clean engine oil.