Right Rear Seat Cover Replacement

Right Rear Seat Cover Replacement

NOTE:

- Take care not to tear the seams or damage the seat covers.
- Put on gloves to protect your hands.

Seat-back Cover

1. Remove the right rear seat Rear Seat Removal/Installation.

2. Remove the rear seat armrest Rear Seat Armrest Removal/Installation.

3. Release the hooks (A), then remove the tether anchor cover (B).






4. Release the bottom hook strip (A), unzip the seat-back cover (B), then fold back the cover. Pull the strap (C) secured on the seat-back frame inside the seat-back cover through the slot (D).






5. Pull back the edge of the rear center seat-back cover (A) all the way around, and release the hooks (B, C, D), then remove the back cover.






6. Release the hook strips (A), then pull the seat-back cover (B).





7. Release the straps (C) from the strap levers (D), then remove the strap out through the slots in the seat-back cover (E) and center pass-through trim (F).

8. Remove the head restraints, then pinch the tabs on the ends of the head restraint guides (A, B) and remove them from the seat-back.

NOTE: To remove the head restraint for '10 model refer to the rear seat head restraint removal/installation Service and Repair.






9. Remove the screws, and remove the center pass-through trim (A) from the center seat-back frame.






10. Release the hook (A). Remove the screws, then remove the rear seat center lower (B) from the center seat-back frame (C).





11. Separate the rear seat-back and the rear seat cushion.

12. Pull back the edge of the seat-back cover (A) all the way around, and release the upholstery rings (B), then remove the seat-back cover.






13. If necessary, remove the screw, then release the hooks (A), and remove the strap lever cover (B).






14. Install the cover in the reverse order of removal, and note these items:

- To prevent wrinkles when installing a seat-back cover, make sure the material is stretched evenly over the pad before securing the upholstery rings and the hook strips.
- Replace any upholstery rings (A) you removed with new ones. Install them with commercially available upholstery ring pliers (B).






Seat Cushion Cover

1. Remove the right rear seat Rear Seat Removal/Installation.

2. Gently pull out the right outer cover (A) and the left outer cover (B) to detach the clips, and release the hooks (C), then remove the covers.










3. Remove the bolts (A, B, C) and the screw (D) securing the seat-back (E) and the seat cushion (F), then separate them.






4. To allow the seat cushion to slide, use a screwdriver to close the latch.






5. Slide both seat tracks (A) back fully.

1. Raise both mounting brackets (B), and place shop towels (C) between the brackets and the bottom cover (D).

2. Push the slide lever (E) down.

3. Slide both seat tracks back fully, taking care not to let the mounting brackets scratch the bottom cover.





6. Remove the screw (A), then pull up the outer seat track cover (B) to detach the clips (C), and remove it. Remove the outer seat track end cover (D). The left seat track is shown, the right seat track is similar.






7. Remove the screws, then remove both dampers (A).






8. Slide both seat tracks (A) forward fully.

1. Raise both mounting brackets (B), and hold them.

2. Push the slide lever (C) down.

3. While holding both mounting brackets, slide both seat tracks forward fully.

NOTE: While sliding the seat tracks, keep both mounting brackets raised securely so they do not spring back.





9. Pull back the rear edge of the seat cushion cover (A) to release it from the hooks (B), and remove the screws.






10. While pushing the slide lever (A) down, remove the undercover (B) by pulling it to release the hooks (C). Pass the strap (D) through its slot, and pass both side cables (E) through the side slots in the cover. Take care not to kink the cables.






11. Release all of the hook strips (A).





12. Remove the rear seat belt buckle and center seat belt detachable anchor Rear Seat Belt Replacement.

13. Remove the seat cushion cover (A) with the seat cushion pad from the seat cushion frame (B). Pass the center seat belt buckle (C) through a hole in the seat cushion cover.






14. Pull back the edge of the seat cushion cover (A) all the way around, and release the upholstery rings (B), then remove the seat cushion cover.






15. Install the cover in the reverse order of removal, and note these items:

- To prevent wrinkles when installing a seat-back cover, make sure the material is stretched evenly over the pad before securing the upholstery rings and the hook strips.
- Replace any upholstery rings (A) you removed with new ones. Install them with commercially available upholstery ring pliers (B).