Compass: Adjustments
Electrical Compass Zone Selection and Calibration
6CD Type
NOTE:
- You should do this procedure any time the electrical compass unit is replaced.
- You should do this procedure in an open area away from buildings, power lines, and other vehicles.
- If you see the CAL indicator (A) and flashing azimuth (direction) indicator (B) appear in the display, the self-calibration is starting automatically. If the compass seems to be continually showing the wrong direction and is not self-calibrating, do the zone selection and calibration.
- Before you select the zone and calibrate the compass, check the No. 17 (20 A) and No. 23 (10 A) fuses in the under-hood fuse/ relay box and the No. 35 (10 A) and No. 36 (10 A) fuses in the under-dash fuse/relay box.
Zone Selection
1. Turn the ignition switch to ON (II), then press and hold the MENU button (A) until the beep (about 5 seconds) to change the display.
2. Rotate the selector knob (B) to select ZONE (C) and press the selector knob to enter the selection.
NOTE: If necessary, press the RETURN button (D) to return to the previous display. Pressing the MENU button cancels the compass setting mode.
3. The display shows the currently selected zone number (A) between from 1 to 15. Find the zone for your area on the zone map. If the correct zone is not shown, turn the selector knob to cycle the zone lists up or down.
4. Press the selector knob to decide the selected zone. Returning to the normal display, the zone selection mode ends.
Calibration
5. While ignition switch is in ON (II), then press and hold the MENU button (A) until the beep (about 5 seconds) to change the display.
6. Rotate the selector knob (B) to select CALIBRATION (C) and press the selector knob to enter the selection.
NOTE: If necessary, press the RETURN button (D) to return to the previous display. Pressing the MENU button cancels the compass setting mode.
7. The display shows PUSH CAL START (A). Pressing the selector knob to begin the calibration, the azimuth display blinks and the CAL indicator (B) is shown.
8. Drive the vehicle slowly in two complete circles. When the calibration is successfully completed, the compass display stops blinking and the CAL indicator goes off.
1CD Type
NOTE:
- You should do this procedure any time the electrical compass unit is replaced.
- You should do this procedure in an open area away from buildings, power lines, and other vehicles.
- If you see the CAL indicator (A) and flashing azimuth (direction) indicator (B) appear in the display, the self-calibration is starting automatically. If the compass seems to be continually showing the wrong direction and is not self-calibrating, do the zone selection and calibration.
- Before you select the zone and calibrate the compass, check the No. 17 (20 A) and No. 23 (10 A) fuses in the under-hood fuse/ relay box and the No. 35 (10 A) and No. 36 (10 A) fuses in the under-dash fuse/relay box.
Zone Selection
1. Turn the ignition switch to ON (II), then press and hold the RPT button (A) and SOUND knob (B) for 2 seconds and changing the display.
2. Press the preset No. 2 button (C) to select ZONE (D), and enter the selection.
3. The display shows the currently selected zone number (A) between 1 and 15. Find the zone for your area on the zone map. If the correct zone is not shown, push the preset button No. 1 (lists down) or No. 2 (lists up) to select the correct zone.
4. Press the preset No. 3 button to decide the selected zone. Returning to the normal display, the zone selection mode ends.
Calibration
5. While ignition switch is in ON (II), press and hold the RPT button (A) and SOUND knob (B) for 2 seconds to change the display.
6. Press the preset No. 1 button (C) to select CAL (D) and enter the selection.
7. While the system calibrates, the azimuth (direction) display (A) blinks and the CAL indicator (B) is shown.
8. Drive the vehicle slowly in two complete circles. When the calibration is successfully completed, the compass display stops blinking and the CAL indicator goes off.