Headliner: Service and Repair
Headliner Removal/Installation
Special Tools Required
- KTC Trim Tool Set SOJATP2014
*Available through the Honda Tool and Equipment Program; 888-424-6857
SRS components are located in this area. Review the SRS component locations Locations and the precautions and procedures Service and Repair before doing repairs or service.
NOTE:
- Put on gloves to protect your hands.
- Take care not to bend or scratch the headliner.
- Be careful not to damage the dashboard and other interior trim.
- Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
1. Remove these items:
- A-pillar trims, both sides
- Front seat belt lower anchor:
- Driver's seat belt
- Passenger's seat belt
- B-pillar lower trims, both sides
- Front seat belt upper anchor, both sides
- B-pillar upper trims, both sides
- Rear seat-back
- Rear trim panel
- Rear seat belt upper anchor, both sides
- C-pillar trims, both sides
- Ceiling light Service and Repair
- Front seat, passenger's side Front Seat Removal/Installation
- Center console Center Console Removal/Installation
2. Release the tabs (A) from both sides of the sunvisor cap (B), using the appropriate trim tool, then release the cap from the bracket (C). Turn the cap and remove it.
3. Remove both sunvisor (A) and holder (B).
1. Remove the screws.
2. Remove the sunvisor from the body and the holder.
3. Disconnect the vanity mirror light connector (C).
4. Push the hook (D) with a flat-tip screwdriver, turn the holder 90 °, then pull it out.
4. Remove the roof console (A).
1. Remove the lenses (B).
2. Remove the bolts.
3. Pull out the roof console and the front individual map light (C).
4. Disconnect the front individual map light connector (D) and if equipped, the navigation microphone/Homelink unit connector (E).
5. From both sides, remove the coat hangers (A).
1. Pry down on the cap (B) with a pick tool (C) wrapped with the protective tape to release the hooks (D), then remove it.
2. Remove the screws.
6. Remove the headliner (A).
1. Remove the front door opening trim (B) and the rear door opening trim (C) from each roof portion.
2. With the help of an assistant, detach the rear clips, and release the fastener (D) and the pin (E) by pulling the rear portion of the headliner down.
3. With moonroof: Detach the front clips by lowering the headliner.
4. Release the Velcro fasteners (F) by lowering the headliner.
5. Lower the headliner, and remove it through the passenger's door opening.
With moonroof
Without moonroof
7. If necessary, remove the bolts, then remove the roof console bracket (A).
8. Install the headliner in the reverse order of removal, and note these items:
- If the side curtain airbag has deployed, replace the headliner, sunvisor on deployed side, and removed trim pieces with new ones Service and Repair.
- To prevent the side curtain airbags from deploying improperly and possibly causing injury, inspect the headliner and all removed trim. Replace any pieces with the following damage:
- Any creases or tears in the headliner (A)
- Any fastener (B) or clip base (C) which have come off the headliner
- Any damage around the coat hanger holes (D) or the sunvisor holes (E) in the headliner
- Any deformation in the coat hangers (F)
- Any cracks in the sunvisor stay bracket (G)
- Any bends or cracks in the sunvisor stay shaft (H)
- Any cracks in the sunvisor base (I)
- Any cracks in the vanity mirror base (J)
- Replace any damaged parts with new ones.
- Make sure the trim piece overlaps the headliner correctly
- When passing the headliner through the door opening, be careful not to fold or bend it. Also, be careful not to scratch the body.
- Check that both sides of the headliner are securely attached to the roof.
- Make sure each connector is plugged in properly.
Headliner
Coat hanger
Sunvisor
