Front Seat-Back Cover Replacement (2-door)
Front Seat-Back Cover Replacement
Special Tools Required
- KTC Trim Tool Set SOJATP2014
- Trim Pad Remover Snap-on A 177A or equivalent, commercially available
*
2-door
SRS components are located in this area. Review the SRS component locations SRS Component Location Index (2-Door) and the precautions and procedures Service and Repair before doing repairs or service.
Do the OPDS sensor initialization after front passenger's seat-back cover replacement.
NOTE:
- Put on gloves to protect your hands.
- Take care not to tear or damage the seat covers.
- Passenger's seat: Do not touch the OPDS sensor in the seat-back pad, and keep it away from oil. Oil can corrode the sensor causing it to fail.
- Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
- The driver's seat is shown; the passenger's seat is similar.
1. Remove the front seat Front Seat Removal/Installation.
2. Driver's seat (10-way power seat): Remove the rear seat access knob (A). Remove the screw, then remove the rear seat access trim (B).
3. From under the seat cushion, release the elastic strap (A) from the seat cushion frame springs (B), then pull back the undercover (C) of the seat-back cover.
4. From under the seat cushion, disconnect and/or detach the connector(s):
- Driver's seat (10-way power seat):
- Side airbag connector (A)
- Recline motor harness connector (B)
- Seat-back heater connector (C)
- Driver's seat (manual height adjustable seat)/ Passenger's seat: Side airbag connector (D)
Driver's seat (10-way power seat without DPMS)
Driver's seat (10-way power seat with DPMS)
Driver's seat (manual height adjustable seat)
Passenger's seat
5. Detach the harness clip(s) (E), and remove the wire tie(s) (F). Driver's seat (manual height adjustable seat): Pry up the hooks (G) of the harness holder (H), then release the holder from the seat cushion frame spring (I).
6. Driver's seat (10-way power seat without DPMS): Release the wire tie (J) of the harness clip fastening the recline motor harness, the seat-back heater harness, and the seat cushion heater harness together.
7. Remove the back panel (A).
1. Remove the screws.
2. Gently pull down the panel to release the hooks (B) from the seat-back frame.
8. Driver's seat (10-way power seat): Pull out the side airbag harness (A), the recline motor harness (B), and the seat-back heater harness (C) through the loops (D). Release the hook strip (E), then pull out the harnesses through the harness holes (F) in the seat-back cover (G).
9. Driver's seat (manual height adjustable seat)/passenger's seat : Pull out the side airbag harnesses (A) through the loop(s) (B). Release the Velcro fasteners (C), the hook strip (D), and pull back the seat-back cover (E), then pull out the harness(es) through the harness hole(s) (F) in the seat-back cover.
Driver's seat (manual height adjustable seat)
Passenger's seat
10. Release the hook strips (A), then loosen the seat-back cover (B).
NOTE: The front seat with leather seat cover is shown; the other types of seats are similar.
11. Remove the nut, then release the bracket (A) of airbag attachment wire C from the seat-back frame (B).
12. Release airbag attachment wire A and airbag attachment wire B from the seat-back frame (C).
13. Driver's seat with lumber support: Remove the lumbar support motor cover (A).
1. Turn over the seat-back cover (B) and the pad (C) as needed.
2. Release the cover from the lower hooks (D).
3. Pull the cover upward to release it from the upper hook (E).
14. Driver's seat with lumber support: Disconnect the seat wire harness connector (F).
15. Passenger's seat: Remove the ODS unit cover (A).
1. Turn over the seat-back cover (B) and the pad (C) as needed.
2. Release the cover from the lower hooks (D).
3. Pull the cover upward to release it from the upper hook (E).
16. Passenger's seat: Disconnect the seat wire harness connector (F) and the OPDS sensor connectors (G).
17. Passenger's seat: Detach the harness clips (A) fastening the OPDS sensor harnesses (B), and release the wire harness from the harness holder (C).
18. Driver's seat with lumber support/passenger's seat: Detach the harness clip (A). Pull the seat wire harness (B) through a hole in the seat frame, and pull it out through the harness hole (C) in the seat-back cover (D). The passenger's seat is shown; the driver's seat is similar.
19. Pinch the tabs on the ends of the head restraint guides (A), and remove them from the seat-back.
20. Remove the seat-back cover/pad (A) from the seat-back frame (B).
21. Pull back the edge of the seat-back cover (A) all the way around, and release the upholstery rings (B), then remove the cover.
NOTE: The leather seat cover is shown; the other types of seat covers are similar.
22. Remove airbag attachment wire B from the outside reinforcing cloths (D). Pull out airbag attachment wire A through the loops (E) of the inside reinforcing cloths (F) and through the loop (G) of airbag attachment wire C. Remove airbag attachment wires A and C.
23. Install the seat-back cover in the reverse order of removal, and note these items:
- If the clips are damaged or stress-whitened, replace them with new ones.
- To prevent wrinkles when installing the seat-back cover, make sure the material is stretched evenly over the pad before securing the upholstery rings, the hooks, and the hook strips.
- Before installing the seat-back cover, make sure airbag attachment wire A, B, and C are installed in the reinforcing cloths (D) correctly, and wire A and wire C are securely assembled.
- Replace all of the upholstery rings (E) fastening the seat-back cover (F) to the pad wires (G) with new ones using commercially available upholstery ring pliers (H).
- Reinstall airbag attachment wires A and B, and the bracket (I) of attachment wire C, securely to the seat-back frame as shown.
- Use only original Honda replacement seat-back covers.
- Make sure the side airbag harness and the seat wire harness are routed properly.
- Push the clips and the hooks into place securely.
