Parking Brake Lever: Service and Repair

Parking Brake Release Handle Assembly Replacement

Removal Procedure

1. Remove the front floor console assembly. Refer to Front Floor Console Replacement (Service and Repair) .




2. Remove the rear front floor console cover assembly to rear floor air outlet duct retaining screws (1).




3. Remove the front floor console cover assembly to rear floor air outlet duct retaining screws (2).
4. Remove the front floor console cover assembly (1).




5. Remove the rear floor air outlet duct to park brake assembly retaining screw (1).




6. Remove the rear floor air outlet duct to park brake assembly retaining screws (2).
7. Remove the park brake assembly (3) from the rear floor air outlet duct (1).



Disassembly Procedure






Important: The park brake lever upper grip (1) is retained by clips and glue. Lift the park brake lever upper grip (1) upwards with your fingers to detach the clips from the park brake lever lower grip (5).



Important: Due to the glue holding them together, the park brake lever upper and lower grips will need replacing once disassembled.


1. Remove the park brake lever upper grip (1) and discard.
2. Detach the park brake lever cable (5) from the park brake lever button (2).
3. Remove the park brake lever button (2) and the park brake lever spring.
4. Remove the park brake lever to park brake lever lower grip retaining screws (3).
5. Remove the park brake lever lower grip (4) and discard.




6. Remove the park brake cable adjustment bolt to park brake assembly retaining circlip (1).
7. Remove the park brake cable adjustment bolt (3).
8. Remove the front park brake cable (2).




9. Remove the pivot pin to park brake assembly retaining circlips (1).




10. Remove the pivot pins (1) and bushes (2) from the park brake base.




11. Separate the park brake lever assembly (1) from the park brake base (2).



Assembly Procedure





1. Install the park brake lever assembly (1) to the park brake base (2).




2. Install the pivot pins (1) and bushes (2) to the park brake base.




3. Install the pivot pin to park brake assembly retaining circlips (3).




4. Install the front park brake cable (2) into position.
5. Install the park brake cable adjustment bolt (3).
6. Install the park brake cable adjustment bolt to park brake assembly retaining circlip (1).




7. Install a NEW park brake lever lower grip (4).
8. Install the park brake lever to park brake lever lower grip retaining screws (3).
9. Install the park brake lever spring and the park brake lever button (2).
10. Attach the park brake lever cable (5) to the park brake lever button (2).

Important: The park brake lever upper grip (1) is retained by clips. Make sure all the clips are aligned with the park brake lever lower grip (4) and are engaged to avoid an induced rattle condition.


11. Install a NEW park brake lever upper grip (1).
Important: This cable adjustment affects the release of the park brake, and could result in accidental release of the park brake.






Installation Procedure





1. Install the park brake (3) to the rear floor air outlet duct (1).
2. Install the rear floor air outlet duct to park brake assembly retaining screws (2).

Tighten the bolt to 2 Nm (18 lb in).





3. Install the rear floor air outlet duct to park brake assembly retaining screw (1).

Tighten the bolt to 2 Nm (18 lb in).





4. Install the front floor console cover assembly (1).
5. Install the front floor console cover assembly to rear floor air outlet duct retaining screws (2).

Tighten the bolt to 2 Nm (18 lb in).





6. Install the rear front floor console cover assembly to rear floor air outlet duct retaining screws (1).

Tighten the bolt to 2 Nm (18 lb in).

7. Install the front floor console assembly. Refer to Front Floor Console Replacement (Service and Repair) .
8. Adjust the park brake. Refer to Parking Brake Adjustment (Adjustments) .