Removal

PARKING BRAKE: PARKING BRAKE CABLE: REMOVAL

REMOVAL
HINT:
- Use the same procedures for the No. 2 parking brake cable assembly and No. 3 parking brake cable assembly.
- The procedures listed below are for the No. 3 parking brake cable assembly.

1. PRECAUTION Removal
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for Manual Seat)
CAUTION: Wait for 90 seconds after disconnecting the cable to prevent the airbag working. Service Precautions

3. REMOVE FRONT SEAT ASSEMBLY LH (for Manual Seat)
HINT: Refer to the procedures up to "REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)". Removal

4. REMOVE FRONT SEAT ASSEMBLY RH (for Manual Seat)
HINT: Use the same procedures for the RH side and the LH side.

5. REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat)
HINT: Refer to the procedures up to "REMOVE FRONT SEAT ASSEMBLY (for Power Seat)". Removal

6. REMOVE FRONT SEAT ASSEMBLY RH (for Power Seat)
HINT: Use the same procedures for the RH side and the LH side.

7. REMOVE PARKING BRAKE LEVER SUB-ASSEMBLY (for Manual Transaxle)
HINT: Refer to the procedures up to "REMOVE PARKING BRAKE LEVER". Removal

8. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY (for Manual Transaxle) Disassembly
9. REMOVE PARKING BRAKE PEDAL ASSEMBLY (for Automatic Transaxle)
HINT: Refer to the procedures up to "REMOVE PARKING BRAKE PEDAL". Removal

10. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY (for Automatic Transaxle) Disassembly
11. REMOVE LUGGAGE DOOR LOCK OPEN LEVER SUB-ASSEMBLY (for Automatic Transaxle) Removal
12. REMOVE FRONT FLOOR CARPET ASSEMBLY (for Automatic Transaxle) Removal
13. REMOVE CROSS MEMBER FLOOR NO. 4 REINFORCEMENT SUB-ASSEMBLY (for Automatic Transaxle) Removal
14. SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY (for Automatic Transaxle)





(a) Separate the No. 3 parking brake cable assembly from the parking brake equalizer.
15. SEPARATE NO. 2 PARKING BRAKE CABLE ASSEMBLY (for Automatic Transaxle)





(a) Separate the No. 2 parking brake cable assembly from the parking brake equalizer.
16. REMOVE NO. 4 PARKING BRAKE CABLE ASSEMBLY (for Automatic Transaxle)





(a) Slide the rubber boot as shown in the illustration.





(b) Remove the No. 4 parking brake cable assembly from the parking brake equalizer as shown in the illustration.
17. REMOVE CENTER EXHAUST PIPE ASSEMBLY (for 2AZ-FE) Removal
18. REMOVE EXHAUST TAIL PIPE ASSEMBLY (for 2GR-FE) Removal
19. REMOVE EXHAUST CENTER PIPE ASSEMBLY (for 2GR-FE) Removal
20. REMOVE NO. 2 FRONT FLOOR HEAT LOWER INSULATOR (for 2AZ-FE)





(a) Remove the 3 nuts and the No. 2 front floor heat lower insulator.
21. REMOVE REAR WHEEL
22. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY Disassembly
23. REMOVE REAR DISC Disassembly
24. REMOVE PARKING BRAKE SHOE RETURN TENSION NO. 1 SPRING Disassembly
25. REMOVE PARKING BRAKE SHOE STRUT Disassembly
26. REMOVE NO. 1 PARKING BRAKE SHOE ASSEMBLY Disassembly
27. REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET Disassembly
28. REMOVE NO. 2 PARKING BRAKE SHOE ASSEMBLY Disassembly
29. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY





(a) Remove the 2 bolts and separate the No. 3 parking brake cable assembly from the backing plate.





(b) Using needle-nose pliers, remove the clip from the No. 3 parking brake cable assembly.
(c) Remove the 3 bolts (A), the bolt (B), and the nut (C), and disengage each claw.





(d) Remove the No. 3 parking brake cable assembly from the body.





(e) Remove the parking brake cable clamp.