Diesel Data: Automotive Repair
Home >> Toyota >> 2009 >> Prius L4-1.5L (1NZ-FXE) Hybrid >> Repair and Diagnosis >> Body and Frame >> Interior Moulding / Trim >> Headliner >> Service and Repair >> Removal

Removal








INTERIOR: ROOF HEADLINING: REMOVAL

REMOVAL

1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

2. REMOVE FRONT DOOR SCUFF PLATE LH





(a) Using a screwdriver, detach the 8 claws and 2 clips, and remove the scuff plate.
HINT: Tape the screwdriver tip before use.

3. REMOVE FRONT DOOR SCUFF PLATE RH
HINT: Use the same procedures described for the LH side.

4. REMOVE COWL SIDE TRIM BOARD LH





(a) Using a screwdriver, detach the claw and 2 clips, and remove the trim board.
HINT: Tape the screwdriver tip before use.

5. REMOVE COWL SIDE TRIM BOARD RH
HINT: Use the same procedures described for the LH side.

6. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
7. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
8. REMOVE FRONT PILLAR GARNISH CORNER PIECE LH





(a) Put protective tape as shown in the illustration.
Standard measurement:






(b) Using a screwdriver, detach the 5 claws and remove the corner piece.
HINT: Tape the screwdriver tip before use.

9. REMOVE FRONT PILLAR GARNISH CORNER PIECE RH
HINT: Use the same procedures described for the LH side.

10. REMOVE FRONT PILLAR GARNISH LH





(a) w/o Curtain Shield Airbag:
Using a screwdriver, detach the 2 clips and remove the pillar garnish.
HINT: Tape the screwdriver tip before use.

(b) w/ Curtain Shield Airbag:
Remove the pillar garnish.




(1) Pull the pillar garnish so that clip B detaches, the base of clip A detaches, and the tip of clip A locks in the pillar garnish's hole.
(2) Using needle-nose pliers, rotate clip A 90°. Then pull the pillar garnish to release the tip of clip A from the pillar garnish.
(3) Pull the pillar garnish in the direction indicated by the arrow in the illustration to detach the claw.





(c) w/ Curtain Shield Airbag:
Protect the curtain shield airbag LH.
(1) Thoroughly cover the airbag with cloth or nylon that is approximately 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover with double-sided tape, as shown in the illustration.
NOTE: Cover the curtain shield airbag with the protective cover as soon as the pillar garnish is removed.

11. REMOVE FRONT PILLAR GARNISH RH
HINT: Use the same procedures described for the LH side.

12. REMOVE REAR SEAT CUSHION ASSEMBLY Removal
13. REMOVE REAR DOOR SCUFF PLATE LH





(a) Using a screwdriver, detach the 6 claws and clip, and remove the scuff plate.
HINT: Tape the screwdriver tip before use.

14. REMOVE REAR DOOR SCUFF PLATE RH
HINT: Use the same procedures described for the LH side.

15. REMOVE REAR SIDE SEATBACK FRAME LH





(a) Remove the bolt.
(b) Detach the claw and remove the frame.
16. REMOVE REAR SIDE SEATBACK FRAME RH
HINT: Use the same procedures described for the LH side.

17. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
18. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
19. REMOVE LAP BELT OUTER ANCHOR COVER





(a) Using a screwdriver, detach the 3 claws and remove the anchor cover.
HINT: Tape the screwdriver tip before use.

20. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
(a) Remove the bolt and disconnect the floor anchor.
21. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
(a) Remove the bolt and disconnect the floor anchor.
22. REMOVE CENTER PILLAR LOWER GARNISH LH





(a) Using a screwdriver, detach the 2 claws and 2 clips, and remove the lower garnish.
HINT: Tape the screwdriver tip before use.

23. REMOVE CENTER PILLAR LOWER GARNISH RH
HINT: Use the same procedures described for the LH side.

24. REMOVE CENTER PILLAR GARNISH LH





(a) Remove the 2 screws.
(b) Using a screwdriver, detach the clip and remove the pillar garnish.
HINT: Tape the screwdriver tip before use.

25. REMOVE CENTER PILLAR GARNISH RH
HINT: Use the same procedures described for the LH side.

26. DISCONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH
(a) Remove the bolt and disconnect the floor anchor.
27. DISCONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH
(a) Remove the bolt and disconnect the floor anchor.
28. REMOVE BACK DOOR WEATHERSTRIP
29. REMOVE TONNEAU COVER ASSEMBLY
30. REMOVE REAR NO. 2 FLOOR BOARD
31. REMOVE REAR NO. 3 FLOOR BOARD
32. REMOVE REAR NO. 4 FLOOR BOARD
33. REMOVE REAR DECK FLOOR BOX
34. REMOVE DECK FLOOR BOX LH
35. REMOVE REAR NO. 1 FLOOR BOARD





(a) Remove the 2 bolts and the 2 rope hooks.
(b) Using a clip remover, remove the 2 clips.
(c) Using a screwdriver, detach the 5 clips and remove the floor board.
HINT: Tape the screwdriver tip before use.

36. REMOVE REAR DECK TRIM COVER





(a) Using a screwdriver, detach the 4 claws and remove the trim cover.
HINT: Tape the screwdriver tip before use.

37. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH





(a) Remove the screw and 2 bolts.
(b) Using a clip remover, remove the clip.
(c) Using a screwdriver, detach the 7 claws and 3 clips, and remove the side panel.
HINT: Tape the screwdriver tip before use.

38. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH





(a) Remove the screw and 2 bolts.
(b) Using a clip remover, remove the clip.
(c) Using a screwdriver, detach the 6 claws and 2 clips, and remove the side panel.
HINT: Tape the screwdriver tip before use.

39. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH





(a) Using a screwdriver, detach the 6 clips and claw, and remove the inner garnish.
HINT: Tape the screwdriver tip before use.

40. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH
HINT: Use the same procedures described for the LH side.

41. REMOVE MAP LIGHT ASSEMBLY





(a) Remove the 2 screws.
(b) Using a moulding remover, detach the 4 clips and remove the map light.
(c) Disconnect the map light connector.
42. REMOVE NO. 1 ROOM LIGHT ASSEMBLY





(a) Using a screwdriver, detach the 4 claws and remove the room light lens.
HINT: Tape the screwdriver tip before use.





(b) Using a screwdriver, detach the 4 claws and remove the room light.
HINT: Tape the screwdriver tip before use.

(c) Disconnect the room light connector.
43. REMOVE ASSIST GRIP COVER





(a) Using a screwdriver, detach the 4 claws and remove the 2 covers.
HINT: Tape the screwdriver tip before use.

44. REMOVE ASSIST GRIP SUB-ASSEMBLY





(a) Using a screwdriver, detach the 4 claws and remove the assist grip.
HINT: Tape the screwdriver tip before use.

45. REMOVE VISOR ASSEMBLY LH





(a) Remove the 2 screws.
(b) Disconnect the connector and remove the visor.
46. REMOVE VISOR ASSEMBLY RH
HINT: Use the same procedures described for the LH side.

47. REMOVE VISOR HOLDER





(a) Remove the visor holder by turning it counterclockwise.
48. REMOVE ROOF HEADLINING ASSEMBLY





(a) Remove the 3 clips and headlining.
(b) Remove the silencer pads and headlining pad from the headlining.
(c) Remove the wire harness.
Diesel-Data.com