Installation

STEERING COLUMN: STEERING COLUMN ASSEMBLY: INSTALLATION

INSTALLATION

1. INSTALL STEERING COLUMN ASSEMBLY





(a) Install the steering column with the 3 bolts.
Torque: 25 Nm (255 kgf-cm, 18 ft-lbf)
(b) Connect the connectors and wire harness clamps to the steering column.





2. INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY
(a) Temporarily install the steering sliding yoke sub-assembly to the steering intermediate shaft with the bolt.





3. INSTALL STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY
(a) Align the matchmarks on the steering intermediate shaft assembly and steering column and install them with the bolt labeled C.
Torque: 35 Nm (360 kgf-cm, 26 ft-lbf)
(b) Align the matchmark on the steering intermediate shaft and steering intermediate shaft and install them with the bolt labeled B.
Torque: 35 Nm (360 kgf-cm, 26 ft-lbf)
(c) Tighten the bolt labeled A on the steering sliding yoke.
Torque: 35 Nm (360 kgf-cm, 26 ft-lbf)
4. INSTALL COLUMN HOLE COVER SILENCER SHEET
5. INSTALL FRONT FLOOR FOOTREST LH
(a) Attach the 2 clips to install the front floor footrest.





6. INSTALL POWER STEERING ECU ASSEMBLY
(a) Connect the 2 steering column connectors to the power steering ECU.
(b) Install the clamp holding the power steering motor and torque sensor wire harness on the bottom surface of the power steering computer.
(c) Install the torque sensor wire harness clamp to the instrument panel reinforcement.
(d) Make sure that the power steering motor and torque sensor wire harnesses do not interfere with other parts while tilting up and down the steering column.
7. INSTALL INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY Installation
8. DISCONNECT PASSENGER AIRBAG CONNECTOR Installation
9. INSTALL FRONT PILLAR GARNISH ASSEMBLY LH Installation
10. INSTALL FRONT PILLAR GARNISH ASSEMBLY RH Installation
11. INSTALL FRONT PILLAR GARNISH CORNER PIECE LH Installation
12. INSTALL FRONT PILLAR GARNISH CORNER PIECE RH Installation
13. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY (w/ JBL Sound System)
14. INSTALL GLOVE COMPARTMENT DOOR Installation
15. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY Installation
16. INSTALL GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY
17. INSTALL MULTI-DISPLAY Installation
18. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY Installation
19. INSTALL NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY Installation
20. INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY Installation
21. INSTALL INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY Installation
22. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY Installation
23. INSTALL COWL SIDE TRIM BOARD RH Installation
24. INSTALL COWL SIDE TRIM BOARD LH Installation
25. INSTALL FRONT DOOR INSIDE SCUFF PLATE LH Installation
26. INSTALL FRONT DOOR INSIDE SCUFF PLATE RH Installation
27. INSTALL SPIRAL CABLE SUB-ASSEMBLY Installation
28. INSPECT SPIRAL CABLE SUB-ASSEMBLY Testing and Inspection
29. INSTALL TURN SIGNAL SWITCH ASSEMBLY
(a) Install the turn signal switch to the steering column with the clamp.
30. INSTALL STEERING COLUMN COVER
(a) Engage the 4 claws to install the steering column upper cover and steering column lower cover.
HINT: Fully tilt down the steering column when installing the steering column upper cover and fully tilt it up when installing the steering column cover.

31. INSTALL TILT LEVER BRACKET
(a) Install the tilt level bracket with the 2 screws.
Torque: 2.0 Nm (20 kgf-cm, 18 in-lbf)
32. INSTALL STEERING WHEEL ASSEMBLY
(a) Align the matchmarks on the steering wheel and steering main shaft.
(b) Install the steering wheel with the set nut.
Torque: 50 Nm (510 kgf-cm, 37 ft-lbf)
33. INSTALL STEERING PAD ASSEMBLY Installation
34. INSPECT STEERING WHEEL CENTER POINT
35. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTICE:
- Make sure that the cable has been disconnected from the battery terminal for at least 2 seconds before reconnecting the cable.
- Connect the cable to the negative (-) battery terminal with the front wheels facing straight ahead.
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.

36. INSPECT STEERING PAD ASSEMBLY
(a) Inspect the steering pad Steering Pad.
37. INSTALL NO. 3 STEERING WHEEL LOWER COVER
38. INSTALL NO. 2 STEERING WHEEL LOWER COVER
39. INSTALL REAR NO. 3 FLOOR BOARD ASSEMBLY
40. INSTALL REAR DECK FLOOR BOX
41. INSTALL REAR NO. 2 FLOOR BOARD
42. INSPECT SRS WARNING LIGHT
(a) Inspect SRS warning light Diagnosis System.
43. PERFORM CALIBRATION
(a) Perform calibration Programming and Relearning.