Removal

REAR SUSPENSION: REAR SUSPENSION MEMBER: REMOVAL

1. REMOVE REAR WHEELS

2. REMOVE CENTER EXHAUST PIPE ASSEMBLY (for 2WD)

HINT
Refer to the procedure up to Remove Center Exhaust Pipe Assembly Removal.

3. REMOVE CENTER EXHAUST PIPE ASSEMBLY (for 4WD)

HINT
Refer to the procedure up to Remove Center Exhaust Pipe Assembly Removal.

4. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD) Removal

5. DRAIN DIFFERENTIAL OIL (for 4WD) Replacement

6. REMOVE REAR AXLE SHAFT NUT LH (for 4WD) Removal

7. REMOVE REAR AXLE SHAFT NUT RH (for 4WD)

HINT
Perform the same procedure for the LH side.

8. REMOVE CHARCOAL CANISTER ASSEMBLY (for 2WD) Removal

9. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY LH Replacement

10. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY RH

HINT
Perform the same procedure for the LH side.

11. REMOVE REAR DISC LH Disassembly

12. REMOVE REAR DISC RH

HINT
Perform the same procedure for the LH side.

13. DISCONNECT REAR SPEED SENSOR WIRE LH (for 2WD) Removal

14. DISCONNECT REAR SPEED SENSOR WIRE RH (for 2WD)

HINT
Perform the same procedure for the LH side.

15. SEPARATE REAR SPEED SENSOR WIRE LH (for 2WD)

(a) Remove the bolt.

(b) Remove the bolt and the nut, and separate the rear speed sensor wire LH.

16. SEPARATE REAR SPEED SENSOR WIRE RH (for 2WD)

HINT
Perform the same procedure for the LH side.

17. SEPARATE REAR SPEED SENSOR LH (for 4WD)

(a) Remove the bolt.

(b) Remove the bolt and the nut, and separate the rear speed sensor LH.

18. SEPARATE REAR SPEED SENSOR RH (for 4WD)

HINT
Perform the same procedure for the LH side.

19. REMOVE NO. 3 PARKING BRAKE SHOE RETURN TENSION SPRING (for LH Side) Disassembly

20. REMOVE NO. 2 PARKING BRAKE SHOE RETURN TENSION SPRING (for LH Side) Disassembly

21. REMOVE NO. 1 PARKING BRAKE SHOE HOLD DOWN COMPRESSION SPRING (for LH Side) Disassembly

22. REMOVE PARKING BRAKE SHOE STRUT (for LH Side) Disassembly

23. REMOVE NO. 2 PARKING BRAKE SHOE HOLD DOWN COMPRESSION SPRING (for LH Side) Disassembly

24. SEPARATE PARKING BRAKE SHOE LEVER (for LH Side) Disassembly

25. REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET (for LH Side) Disassembly

26. REMOVE NO. 1 PARKING BRAKE SHOE RETURN TENSION SPRING (for LH Side) Disassembly

27. REMOVE PARKING BRAKE SHOE LEVER (for LH Side) Disassembly

28. REMOVE NO. 1 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for LH Side) Disassembly

29. REMOVE NO. 2 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for LH Side) Disassembly

30. REMOVE NO. 3 PARKING BRAKE SHOE RETURN TENSION SPRING (for RH Side)

HINT
Perform the same procedure for the LH side.

31. REMOVE NO. 2 PARKING BRAKE SHOE RETURN TENSION SPRING (for RH Side)

HINT
Perform the same procedure for the LH side.

32. REMOVE NO. 1 PARKING BRAKE SHOE HOLD DOWN COMPRESSION SPRING (for RH Side)

HINT
Perform the same procedure for the LH side.

33. REMOVE PARKING BRAKE SHOE STRUT (for RH Side)

HINT
Perform the same procedure for the LH side.

34. REMOVE NO. 2 PARKING BRAKE SHOE HOLD DOWN COMPRESSION SPRING (for RH Side)

HINT
Perform the same procedure for the LH side.

35. SEPARATE PARKING BRAKE SHOE LEVER (for RH Side)

HINT
Perform the same procedure for the LH side.

36. REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET (for RH Side)

HINT
Perform the same procedure for the LH side.

37. REMOVE NO. 1 PARKING BRAKE SHOE RETURN TENSION SPRING (for RH Side)

HINT
Perform the same procedure for the LH side.

38. REMOVE PARKING BRAKE SHOE LEVER (for RH Side)

HINT
Perform the same procedure for the LH side.

39. REMOVE NO. 1 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for RH Side)

HINT
Perform the same procedure for the LH side.

40. REMOVE NO. 2 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for RH Side)

HINT
Perform the same procedure for the LH side.

41. SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY

(a) Remove the 2 bolts.

(b) Remove the bolt and separate the No. 3 parking brake cable assembly.

42. SEPARATE NO. 2 PARKING BRAKE CABLE ASSEMBLY

HINT
Perform the same procedure for the No. 3 parking brake cable assembly.

43. SEPARATE REAR STABILIZER LINK ASSEMBLY LH Removal

44. SEPARATE REAR STABILIZER LINK ASSEMBLY RH

HINT
Perform the same procedure for the LH side.

45. SEPARATE UPPER CONTROL ARM ASSEMBLY LH Removal

46. SEPARATE UPPER CONTROL ARM ASSEMBLY RH

HINT
Perform the same procedure for the LH side.

47. SEPARATE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH Removal

48. SEPARATE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT
Perform the same procedure for the LH side.

49. REMOVE REAR AXLE ASSEMBLY LH (for 2WD)

50. REMOVE REAR AXLE ASSEMBLY RH (for 2WD)

51. REMOVE REAR AXLE ASSEMBLY LH (for 4WD) Removal

52. REMOVE REAR AXLE ASSEMBLY RH (for 4WD)

HINT
Perform the same procedure for the LH side.

53. REMOVE REAR DRIVE SHAFT ASSEMBLY LH (for 4WD) Removal

54. REMOVE REAR DRIVE SHAFT SNAP RING LH (for 4WD) Removal

55. REMOVE REAR DRIVE SHAFT ASSEMBLY RH (for 4WD)

HINT
Perform the same procedure for the LH side.

56. REMOVE REAR DRIVE SHAFT SNAP RING RH (for 4WD)

HINT
Perform the same procedure for the LH side.

57. REMOVE REAR FLOOR SIDE MEMBER BRACE Removal

58. LOOSEN REAR SHOCK ABSORBER WITH COIL SPRING (for LH Side) Removal

59. LOOSEN REAR SHOCK ABSORBER WITH COIL SPRING (for RH Side)

HINT
Perform the same procedure for the LH side.

60. REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

(a) Remove the bolt and nut, and separate the rear No. 1 suspension arm assembly LH from the rear suspension member.

NOTICE:
When removing the bolt, stop the nut from rotating and loosen the bolt.

(b) Remove the 3 bolts, and separate the rear No. 1 suspension arm assembly LH.

61. REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT
Perform the same procedure for the LH side.

62. REMOVE REAR SUSPENSION MEMBER (for 2WD)

(a) Support the rear suspension member using a jack and wooden block.

(b) Remove the 2 bolts and 2 nuts from the rear suspension member.

(c) Lower the rear suspension member.

63. REMOVE REAR SUSPENSION MEMBER (for 4WD)

(a) Disconnect the wire harness connector and the hose.

(b) Disengage the 6 clamps and separate the wire harness and hose.

(c) Support the rear suspension member using a jack and wooden block.

(d) Remove the 2 bolts and 2 nuts from the rear suspension member.

(e) Lower the rear suspension member.

64. REMOVE UPPER CONTROL ARM ASSEMBLY LH Removal

65. REMOVE UPPER CONTROL ARM ASSEMBLY RH

HINT
Perform the same procedure for the LH side.

66. REMOVE REAR NO. 1 STABILIZER BAR BRACKET Removal

67. REMOVE REAR STABILIZER BUSHING Removal

68. REMOVE REAR STABILIZER BAR

69. REMOVE HOLE PLUG

(a) Remove the 9 hole plugs.

70. REMOVE NO. 6 EXHAUST PIPE SUPPORT BRACKET (for 4WD)

(a) Remove the 2 bolts and No. 6 exhaust pipe support bracket.

71. REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) Removal

72. REMOVE REAR NO. 1 DIFFERENTIAL MOUNT CUSHION (for 4WD) Removal

73. REMOVE STUD BOLT

(a) Remove the 2 stud bolts.