Touching Unlock Sensor for Certain Period of Time does not Unlock All Doors [11/2023 - ]: Procedure

1. When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

   Refer to OPERATION CHECK [11/2023 - ]

   OK

   Door locks operate normally.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

GO TO POWER DOOR LOCK CONTROL SYSTEM 

Refer to HOW TO PROCEED WITH TROUBLESHOOTING [11/2023 - ]

Result: 

OK 

See step  2

1. Read the customize setting according to the display on the GTS.

   Smart Key / Access 

   Tester Display	Description	Default	Setting	ECU
   Door Unlock Sensor Touch Time Adjust	Function that sets the length of time the unlock sensor on the door outside handle assembly (for driver door) must be touched to unlock all of the doors.*1	Middle	$00:OFF, $01:Short, $02:Middle, $03:Long	Certification ECU (Smart key ECU assembly)
   Entry Unlock Twice Function	Function that unlocks only the driver door when performing the entry unlock operation.*2	Enable	$00:Disable, $01:Enable	Main body ECU (Multiplex network body ECU)

   1. *1: When the following conditions are met, a short touch unlocks only the driver door, while a long touch unlocks all of doors.
      • "Door Unlock Sensor Touch Time Adjust" is set to other than "OFF"
      • "Entry Unlock Twice Function" is set to "Enable"*2
   2. *2: Customize settings cannot be selected from "Smart Key / Access" if the vehicle recognizes driver 1, 2 or 3 with the My Settings function. In that case, change the settings from "My Settings".

      Refer to CUSTOMIZE PARAMETERS [11/2023 - ]

   Result

   Result	Proceed to
   When the following conditions are met:  "Door Unlock Sensor Touch Time Adjust" is set to other than "OFF" "Entry Unlock Twice Function" is set to "Enable"	A
   Other than the above condition	B

Result: 

B 

PERFORM CUSTOMIZE SETTING 

Refer to CUSTOMIZE PARAMETERS [11/2023 - ]

Result: 

A 

See step  3

1. Turn the ignition switch off.
2. Open and close the driver door.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Unlock Sensor (Backside)

   The illustrations shown are examples only.

3. With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.
4. Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.
5. Check that the LED of the electrical key transmitter sub-assembly blinks.
6. Read the Data List according to the display on the GTS.
7. Touch the unlock sensor on the backside of the front door outside handle assembly (for driver door) for 2 seconds or more.*
   1. *: Perform this step 3 seconds or more after performing step (c).

   HINT: 

   When checking the operation of the unlock sensor again, make sure to perform the procedure from step (a).

   Body Electrical > Smart Key > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Driver Side Unlock Sensor	Driver door touch sensor (unlock sensor)	OFF or ON	OFF: Driver door touch sensor (unlock sensor) not touched ON: Driver door touch sensor (unlock sensor) touched	Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily). Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.

   OK

   The GTS display changes correctly in response to the operation of the front door outside handle assembly (for driver door).

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 

Refer to REMOVAL [11/2023 - ]

Result: 

NG 

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR) 

Refer to DISASSEMBLY [11/2023 - ]