Data List / Active Test [12/2019 - 11/2023]
- DATA LIST NOTE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- Connect the GTS to the DLC3.
- Turn the ignition switch to ON.
- Turn the GTS on.
- Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Data List.
- Read the Data List according to the display on the GTS.
Body Electrical > Blind Spot Monitor Master > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note Main Switch State of the Blind spot monitor system OFF or ON OFF: Blind spot monitor system off
ON: Blind spot monitor system on- RCTA Switch Status State of RCTA function OFF or ON OFF: RCTA function off
OFF: RCTA function on- Warning Indicator Turning on (Master) State of the outer rear view mirror indicator LH turning on OFF or ON - OFF: Any state except "ON"
- ON: Either of the following states
- During initial check
- Blind spot monitor system on, vehicle detected on left hand side and left turn signal switch not on
- Warning Indicator Flashing (Master) State of the outer rear view mirror indicator LH flashing OFF or ON OFF: Any state except "ON"
ON: Blind spot monitor system on, vehicle detected on left hand side and left turn signal switch on- Warning Indicator Input Circuit Voltage Outer rear view mirror indicator voltage Min.: 0 V, Max.: 25.5 V Indicator illuminated: 2.5 to 7.5 V
Indicator not illuminated: Below 1 V- Warning Indicator Input Circuit Current Outer rear view mirror indicator current Min.: 0 mA, Max.: 255 mA Indicator illuminated: 5 to 100 mA
Indicator not illuminated: 0 mA- Turn Switch State State of the turn signal switch Left ON, Right ON or OFF Left ON: Left turn signal switch on
Right ON: Right turn signal switch on
OFF: Turn signal switch off- Reverse (Only for AT/CVT) State of the shift position R signal OFF or ON OFF: Shift lever in any position except R
ON: Shift lever in R- Vehicle Speed Vehicle speed signal Min.: -327.68 km/h (-204 mph), Max.: 327.67 km/h (204 mph) Vehicle stopped: 0 km/h (0 mph) - Steering Angle Steering angle sensor Min.: -3072 deg, Max.: 3070.5 deg Left turn: Increases
Right turn: Decreases- VGRS Relative Angle Compensation value of steering angle calculated by VGRS Min.: -8.192 rad
Max.: 8.191 radLeft turn: Increases
Right turn: Decreasesw/ Variable Gear Ratio Steering System Power Supply Voltage Power supply voltage Min.: 0 V, Max.: 49.951 V Ignition switch ON: 11 to 14 V - Indicator Light Control State Outer rear view mirror indicator dimming state Dim OFF or Dim ON Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed- HV Flag Hybrid vehicle OFF or ON OFF: Non-hybrid vehicle
ON: Hybrid vehicle- VGRS Flag VGRS installed OFF or ON OFF: VGRS not installed
ON: VGRS installed- Beam Axis Inspection Completeness Flag Completion of beam axis adjustment Incompl or Compl Incompl: Adjustment not completed
Compl: Adjustment completedChanges to "Compl" when blind spot monitor beam axis adjustment has been finished Destination Undefined Flag Destination determination Unfixed or Fixed Unfixed: Sensor destination information not determined
Fixed: Sensor destination information determined according to CAN destination information- Angle Adjustment by Auto Alignment Angle adjusted using auto alignment Min.: Under -180 deg, Max.: Over 180 deg Angle adjusted using auto alignment is displayed - BSM Function BSM function Valid or Invalid Valid: BSM function on
Invalid: BSM function off- RCTA Equipped Information State of the RCTA equipped information / OFF or ON OFF or ON OFF: w/o RCTA function
ON: w/ RCTA function- Master Side RCTA Function Switches the RCTA function on and off OFF or ON ON: RCTA function on
OFF: RCTA function off- Outer Mirror Type State of the outer mirror type Pending, Optical or Electronic Pending: Outer mirror type pending
Optical: Outer mirror optical type
Electronic: Outer mirror Electronic type- Mirror LED Control Frequency Frequency of the outer rear view mirror indicator on the outer mirror when blinking Min.: 1500 Hz, Max.: 2400 Hz Always: 2000 Hz - Setting of Warning Indicator Current (Dim OFF) Set current of the outer rear view mirror indicator when not dimmed Min.: 0 mA, Max.: 100 mA Always: 0 to 100 mA - Setting of Warning Indicator Current (Dim ON) Set current of the outer rear view mirror indicator when dimmed Min.: 0 mA, Max.: 100 mA Always: 0 to 100 mA - Mirror LED Duty Ratio (Blinking) Duty ratio of the outer rear view mirror indicator when blinking Min.: 0%, Max.: 100% Always: 50% - Yaw Rate Sensor Yaw rate sensor Min.: Under -124.928 deg/s, Max.: 124.684 deg/s Turning right: -124.928 to 0 deg/s
Turning left: 0 to 124.684 deg/s- Master Side BSM Approaching Vehicle Detection Timing Setting Notification timing for vehicles approaching from behind the vehicle Only Blind Spot, Late, Middle or Early Only Blind Spot: Only detection area (for vehicle in blind spot) is active
Late: Late notification
Middle: Default notification timing
Early: Early notification- BSM Mirror Indicator Brightness Brightness of the indicators in the outer rear view mirror assemblies Dark or Bright Dark: Outer mirror indicator brightness low
Bright: Outer mirror indicator brightness high- Mounting FHL Function Existence of FHL function Without or With Without: w/o FHL function
With: w/ FHL function- FHL Function Operation condition of proximity warning function for vehicles to the rear OFF or ON OFF: The proximity warning function for vehicles to the rear is not operating
ON: The proximity warning function for vehicles to the rear is operating- Number of DTC Number of DTCs Min.: 0, Max.: 255 When system is normal: 0
When a malfunction is detected: More than 0- Body Electrical > Blind Spot Monitor Slave > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note Warning Indicator Turning on (Slave) State of the outer rear view mirror indicator RH turning on OFF or ON - OFF: Any state except "ON"
- ON: Either of the following states
- During initial check
- Blind spot monitor system on, vehicle detected on right hand side and right turn signal switch not on
- Warning Indicator Flashing (Slave) State of the outer rear view mirror indicator RH flashing OFF or ON OFF: Any state except "ON"
ON: Blind spot monitor system on, vehicle detected on right hand side and right turn signal switch on- Buzzer Sound Status State of the RCTA buzzer (blind spot monitor buzzer) OFF or ON OFF: Buzzer not sounding
ON: Buzzer sounding- Warning Indicator Input Circuit Voltage Outer rear view mirror indicator voltage Min.: 0 V, Max.: 25.5 V Indicator illuminated: 2.5 to 7.5 V
Indicator not illuminated: Below 1 V- Warning Indicator Input Circuit Current Outer rear view mirror indicator current Min.: 0 mA, Max.: 255 mA Indicator illuminated: 5 to 100 mA
Indicator not illuminated: 0 mA- Buzzer Input Circuit Voltage RCTA buzzer (blind spot monitor buzzer) voltage Min.: 0 V, Max.: 25.5 V Buzzer not sounding: 11 to 14 V
Buzzer sounding: Alternating between 0 to 14 V- Turn Switch State State of the turn signal switch Left ON, Right ON or OFF Left ON: Left turn signal switch on
Right ON: Right turn signal switch on
OFF: Turn signal switch off- Reverse (Only for AT/CVT) State of the shift position R signal OFF or ON OFF: Shift lever in any position except R
ON: Shift lever in R- Reverse (Only for MT) State of the shift position R signal OFF or ON OFF: Shift lever in any position except R
ON: Shift lever in R- Vehicle Speed Vehicle speed signal Min.: -327.68 km/h (-204 mph), Max.: 327.67 km/h (204 mph) Vehicle stopped: 0 km/h (0 mph) - Steering Angle Steering angle sensor Min.: -3072 deg, Max.: 3070.5 deg Left turn: Increases
Right turn: Decreases- VGRS Relative Angle Compensation value of steering angle calculated by VGRS Min.: -8.192 rad
Max.: 8.191 radLeft turn: Increases
Right turn: Decreasesw/ Variable Gear Ratio Steering System Power Supply Voltage Power supply voltage Min.: 0 V, Max.: 49.951 V Ignition switch ON:
11 to 14 V (for HV Model)
10.5 to 16 V (for Gasoline Model)- Indicator Light Control State Outer rear view mirror indicator dimming state Dim OFF or Dim ON Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed- HV Flag Hybrid vehicle OFF or ON OFF: Non-hybrid vehicle
ON: Hybrid vehicle- VGRS Flag VGRS installed OFF or ON OFF: VGRS not installed
ON: VGRS installed- Beam Axis Inspection Completeness Flag Completion of beam axis adjustment Incompl or Compl Incompl: Adjustment not completed
Compl: Adjustment completedChanges to "Compl" when blind spot monitor beam axis adjustment has been finished Destination Undefined Flag Destination determination Unfixed or Fixed Unfixed: Sensor destination information not determined
Fixed: Sensor destination information determined according to CAN destination information- Buzzer Connection Connection status of the buzzer Valid or Invalid Valid: Connection
Invalid: No connection- Angle Adjustment by Auto Alignment Angle adjusted using auto alignment Min.: Under -180 deg, Max.: Over 180 deg Angle adjusted using auto alignment is displayed - BSM Function BSM function Valid or Invalid Valid: BSM function on
Invalid: BSM function off- RCTA Equipped Information State of the RCTA equipped information / OFF or ON OFF or ON OFF: w/o RCTA function
ON: w/ RCTA function- Slave Side RCTA Function Switches the RCTA function on and off OFF or ON OFF: RCTA function off
ON: RCTA function on- Outer Mirror Type State of the outer mirror type Pending, Optical or Electronic Pending: Outer mirror type pending
Optical: Outer mirror optical type
Electronic: Outer mirror Electronic type- Mirror LED Control Frequency Frequency of the outer rear view mirror indicator on the outer mirror when blinking Min.: 1500 Hz, Max.: 2400 Hz Always: 2000 Hz - Setting of Warning Indicator Current (Dim OFF) Set current of the outer rear view mirror indicator when not dimmed Min.: 0 mA, Max.: 100 mA Always: 0 to 100 mA - Setting of Warning Indicator Current (Dim ON) Set current of the outer rear view mirror indicator when dimmed Min.: 0 mA, Max.: 100 mA Always: 0 to 100 mA - Mirror LED Duty Ratio (Blinking) Duty ratio of the outer rear view mirror indicator when blinking Min.: 0%, Max.: 100% Always: 50% - Buzzer Control Frequency Frequency of RCTA buzzer (blind spot monitor buzzer) when sounding Min.: 1000 Hz, Max.: 2400 Hz Always: 2000 Hz - Yaw Rate Sensor Yaw rate sensor Min.: Under -124.928 deg/s, Max.: 124.684 deg/s Turning right: -124.928 to 0 deg/s
Turning left: 0 to 124.684 deg/s- BSM Buzzer Volume Adjust Volume of the RCTA buzzer (blind spot monitor buzzer) Low, Medium or High Low: Buzzer volume less than that of medium
Medium: Default buzzer volume
High: Buzzer volume more than that of medium- Slave Side BSM Approaching Vehicle Detection Timing Setting Notification timing for vehicles approaching from behind the vehicle Only Blind Spot, Late, Middle or Early Only Blind Spot: Only detection area (for vehicle in blind spot) is active
Late: Late notification
Middle: Default notification timing
Early: Early notification- Mounting FHL Function Existence of FHL function Without or With Without: w/o FHL function
With: w/ FHL function- FHL Function Operation condition of proximity warning function for vehicles to the rear OFF or ON OFF: The proximity warning function for vehicles to the rear is not operating
ON: The proximity warning function for vehicles to the rear is operating- Number of DTC Number of DTCs Min.: 0, Max.: 255 When system is normal: 0
When a malfunction is detected: More than 0-