Data List / Active Test [11/2023 - ]
- DATA LIST NOTE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- Connect the GTS to the DLC3.
- Turn the ignition switch to ON.
- Turn the GTS on.
- Enter the following menus: Body Electrical / Blind Spot Monitor "B" or Blind Spot Monitor "A" / Data List.
- Read the Data List according to the display on the GTS.
Body Electrical > Blind Spot Monitor "B" > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note Total Distance Traveled Total distance traveled 0 to 16777215 - - Total Distance Traveled - Unit Total Distance Traveled - Unit km or mile - - Power Supply Voltage Power supply voltage 0 to 49.95 V Ignition switch ON:
11 to 14 V- BSM Outer Mirror Indicator Information (Left) Status of indicator Extinction, Lighting or Blinking - - BSM Outer Mirror Indicator Information (Right) Status of indicator Extinction, Lighting or Blinking - - LED Outer Mirror Indicator Voltage (Currently Value) Voltage value of indicator 0 to 25.5 V - - LED Outer Mirror Indicator Current (Currently Value) Electrical current value of indicator 0 to 255 mA - - Dimmer Signal Status of dimmer signal OFF or ON - - Clearance Warning Buzzer Support Status of clearance warning buzzer support Pending, Not Support or Support - - RCTA Equipped Information State of the RCTA equipped information Without or With With: RCTA function equipped
Without: RCTA function not equipped- FHL Equipped Information State of the FHL equipped information Without or With With: FHL function equipped
Without: FHL function not equipped- Outer Mirror Type Status of outer mirror type Pending, Optical or Electronic - - Shift Position R State of the shift position R signal OFF or ON OFF: Shift position in any other than R
ON: Shift position in R- Vehicle Speed Vehicle speed signal -327.68 to 327.67 km/h Almost same as actual vehicle speed - Steering Angle Steering angle sensor -3072 to 3070.5 deg Left turn: Increases
Right turn: Decreases- Yaw Rate Yaw rate sensor -125 to 124.612 deg/s Turning right: -124.928 to 0 deg/s
Turning left: 0 to 124.684 deg/s- Turn Switch State of the turn signal switch Left, Right or OFF Left: Left turn signal switch on
Right: Right turn signal switch on
OFF: Turn signal switch off- BSM Main Switch Operation Count (Data 1) Number of times BSM main switch was operated 0 to 66635 - - BSM Main Switch Operation Count (Data 2) Number of times BSM main switch was operated 0 to 66635 - - RCTA Main Switch Operation Count (Data 1) Number of times RCTA main switch was operated 0 to 66635 - - RCTA Main Switch Operation Count (Data 2) Number of times RCTA main switch was operated 0 to 66635 - - L-BSM Mode Operation Count Number of times L-BSM was operated 0 to 66635 - - Outer Mirror Indicator Brightness Setting Operation Count Number of times outer mirror indicator brightness setting was operated 0 to 66635 - - Clearance Warning Buzzer Malfunction State of clearance warning buzzer malfunction No or Yes - - Steering Angle Sensor Malfunction State of steering angle sensor malfunction No or Yes - - Yaw Rate Sensor Malfunction State of yaw rate sensor malfunction No or Yes - - Speed Sensor Malfunction State of speed sensor malfunction No or Yes - - Outer Mirror Indicator Brightness Status of outer mirror indicator brightness setting Dark or Bright Dark: Outer mirror indicator is dimmed
Bright: Outer mirror indicator is not dimmed- LED Outer Mirror Indicator Current (Dimmer OFF, Bright) Electrical current flow to indicator in Bright setting with dimmer OFF 0 to 100 mA - - LED Outer Mirror Indicator Current (Dimmer OFF, Dim) Electrical current flow to indicator in Dim setting with dimmer OFF 0 to 100 mA - - LED Outer Mirror Indicator Current (Dimmer ON, Bright) Electrical current flow to indicator in Bright setting with dimmer ON 0 to 100 mA - - LED Outer Mirror Indicator Current (Dimmer ON, Dim) Electrical current flow to indicator in Dim setting with dimmer ON 0 to 100 mA - - LED Outer Mirror Indicator Blinking Duty Ratio Duty ratio when indicator blinking 0 to 100 % - - L-BSM Mode Status of L-BSM mode setting OFF, Short, Middle or Long - - BSM Function State of the BSM function Valid or Invalid - - RCTA Function State of the RCTA function Valid or Invalid - - Beam Axis Revision Angle Compensation angle of beam axis -327.68 to 327.67 deg - - Destination Information Status of destination information confirmation Defined or Undefined Defined: Destination information is confirmed
Undefined: Destination information is not confirmed- RCTA Function Set Invalid History Whether vehicle is equipped with RCTA function Not Recorded or Recorded - - BSM Function Set Invalid History Whether vehicle is equipped with BSM function Not Recorded or Recorded - - Body Electrical > Blind Spot Monitor "A" > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note Total Distance Traveled Total distance traveled 0 to 16777215 - - Total Distance Traveled - Unit Total distance traveled unit km or mile - - Power Supply Voltage Power supply voltage 0 to 49.95 V Ignition switch ON:
11 to 14 V- LED Outer Mirror Indicator Voltage (Currently Value) Voltage value of indicator 0 to 25.5 V - - LED Outer Mirror Indicator Current (Currently Value) Electrical current value of indicator 0 to 255 mA - - Dimmer Signal Status of dimmer signal OFF or ON - - Buzzer Sound Request Alarm status of clearance warning buzzer OFF or ON OFF: When the following condition is not met
ON: While the rear cross traffic alert function is operating, the sensor issues a vehicle warning- Buzzer Voltage RCTA buzzer (blind spot monitor buzzer) voltage Min.: 0 V, Max.: 25.5 V Buzzer not sounding: 11 to 14 V
Buzzer sounding: Alternating between 0 to 14 Vw/o Intuitive Parking Assist System Clearance Warning Buzzer Support Status of clearance warning buzzer support Pending, Not Support or Support Not Support: No. 2 clearance warning buzzer support not available
Support: No. 2 clearance warning buzzer support available- RCTA Equipped Information State of the RCTA equipped information Without or With With: RCTA function equipped
Without: RCTA function not equipped- FHL Equipped Information State of the FHL equipped information Without or With With: FHL function equipped
Without: FHL function not equipped- VGRS Equipped Information State of the VGRS equipped information Without or With With: VGRS function equipped
Without: VGRS function not equipped- Outer Mirror Type Status of outer mirror type Pending, Optical or Electronic - - Shift Position R State of the shift position R signal OFF or ON OFF: Shift position in any other than R
ON: Shift position in R- Vehicle Speed Vehicle speed signal -327.68 to 327.67 km/h Almost same as actual vehicle speed - Steering Angle Steering angle sensor -3072 to 3070.5 deg Left turn: Increases
Right turn: Decreases- Yaw Rate Yaw rate sensor -124.928 to 124.684 deg/s Turning right: -124.928 to 0 deg/s
Turning left: 0 to 124.684 deg/s- Turn Switch State of the turn signal switch OFF or ON Left: Left turn signal switch on
Right: Right turn signal switch on
OFF: Turn signal switch off- BSM Main Switch Operation Count (Data 1) Number of times BSM main switch was operated 0 to 66635 - - BSM Main Switch Operation Count (Data 2) Number of times BSM main switch was operated 0 to 66635 - - RCTA Main Switch Operation Count (Data 1) Number of times RCTA main switch was operated 0 to 66635 - - RCTA Main Switch Operation Count (Data 2) Number of times RCTA main switch was operated 0 to 66635 - - Rear Side Radar Sensor Blockage Whether radar sensor is dirty No or Yes - RoB X217A is output if Rec Rear Side Radar Sensor Blockage Level 2 Whether radar sensor is dirty No or Yes - RoB X217B is output if Rec Rear Side Radar Sensor Outside Guaranteed Operating Temperature Radar sensor temperature abnormality No or Yes - RoB X2178 is output if Rec Rear Side Radar Sensor Outside Guaranteed Operating Voltage Radar sensor voltage abnormality No or Yes - RoB X2179 is output if Rec Rear Side Radar Sensor Beam Axis Not Adjusted Radar sensor beam axis has not been adjusted No or Yes - RoB X2177 is output if Rec Outer Mirror Indicator Brightness Status of outer mirror indicator brightness setting Dark or Bright Dark: Outer mirror indicator dimmed
Bright: Outer mirror indicator not dimmed- LED Outer Mirror Indicator Current (Dimmer OFF, Bright) Electrical current flow to indicator in Bright setting with dimmer OFF 0 to 100 mA - - LED Outer Mirror Indicator Current (Dimmer OFF, Dim) Electrical current flow to indicator in Dim setting with dimmer OFF 0 to 100 mA - - LED Outer Mirror Indicator Current (Dimmer ON, Bright) Electrical current flow to indicator in Dim setting with dimmer OFF 0 to 100 mA - - LED Outer Mirror Indicator Current (Dimmer ON, Dim) Electrical current flow to indicator in Dim setting with dimmer ON 0 to 100 mA - - LED Outer Mirror Indicator Blinking Duty Ratio Duty ratio when indicator blinking 0 to 100 % - - RCTA Buzzer Volume Volume setting of the RCTA buzzer Small, Middle or Large Customized setting w/o Intuitive Parking Assist System RCTA Buzzer Sound Frequency Frequency of RCTA buzzer (blind spot monitor buzzer) when sounding 1000 to 2400 Hz Always: 2000 Hz w/o Intuitive Parking Assist System RCTA Buzzer Sound Duty Ratio (Large) Duty ratio when RCTA buzzer large sounding 0 to 100 % - w/o Intuitive Parking Assist System RCTA Buzzer Sound Duty Ratio (Middle) Duty ratio when RCTA buzzer middle sounding 0 to 100 % - w/o Intuitive Parking Assist System RCTA Buzzer Sound Duty Ratio (Small) Duty ratio when RCTA buzzer small sounding 0 to 100 % - w/o Intuitive Parking Assist System L-BSM Mode Status of L-BSM mode setting OFF, Short, Middle or Long - - BSM Function State of the BSM function Valid or Invalid - - RCTA Function State of the RCTA function Valid or Invalid - - Beam Axis Revision Angle Compensation angle of beam axis -327.68 to 327.67 deg - - Destination Information Status of destination information confirmation Defined or Undefined Defined: Destination information is confirmed
Undefined: Destination information is not confirmed- RCTA Function Set Invalid History Whether vehicle is equipped with RCTA function Not Recorded or Recorded - - BSM Function Set Invalid History Whether vehicle is equipped with BSM function Not Recorded or Recorded - -