DSD Information System
Home >> Toyota >> 2021 >> Highlander LE, 4WD >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Collision/Avoidance >> Front Radar Sensor System - Diagnostic Codes >> Front Radar Sensor System >> DTC U0104-87: Lost Communication with Cruise Control Module Missing Message [11/2023 - ] >> Procedure

DTC U0104-87: Lost Communication with Cruise Control Module Missing Message [11/2023 - ]: Procedure

  1. CHECK FOR DTCs 
    1. Check for pre-collision system DTCs.

      Body Electrical > Pre-Collision System > Trouble Codes 

      Result

      Result Proceed to
      DTC U0235-87 is output A
      DTC U0235-87 is not output B

    Result: 

    B 

    See step  4

    Result: 

    A 

    See step  2

  2. CHECK CAN BUS LINES 
    GTY922064Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *1 DLC3 - -
    *a Front view of wire harness connector
    (to Forward Recognition Camera)    		 - -
    1. Disconnect the R5 forward recognition camera connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      R5-6 (CANH) - R5-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132Ω
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      R5-6 (CANH) - H56-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      R5-12 (CANL) - H56-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      R5-6 (CANH) - H56-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      R5-12 (CANL) - H56-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
    4. Connect the R5 forward recognition camera connector.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE FORWARD RECOGNITION CAMERA. Refer to  REMOVAL [11/2023 - ] 

    Result: 

    NG 

    See step  3

  3. CHECK CAN BUS LINES 
    GTY906317Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *1 DLC3 - -
    *a Front view of wire harness connector
    (to Millimeter Wave Radar Sensor Assembly)    		 - -
    1. Disconnect the B6 millimeter wave radar sensor assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      B6-5 (CA1P) - B6-6 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132Ω
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      B6-5 (CA1P) - H56-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      B6-6 (CA1N) - H56-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
      B6-5 (CA1P) - H56-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
      B6-6 (CA1N) - H56-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
    4. Connect the B6 millimeter wave radar sensor assembly connector.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY. Refer to  REMOVAL [11/2023 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR 

  4. CHECK CONNECTOR (FORWARD RECOGNITION CAMERA) 
    1. Check the locking part and terminals of the forward recognition camera connector.
      NOTE:
      • Make sure the connector is not loose or disconnected.
      • Make sure that the connector and terminals are not deformed or corroded.

      OK

      The connector and terminals are normal.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR (FORWARD RECOGNITION CAMERA) 

    Result: 

    OK 

    See step  5

  5. CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA POWER SOURCE CIRCUIT) 
    GTY896486Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Front view of wire harness connector
    (to Forward Recognition Camera)
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the R5 forward recognition camera connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      R5-10 (GND) - Body ground Always Below 1 Ω
    4. Connect the cable to the negative (-) auxiliary battery terminal.
    5. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      R5-7 (IGB) - Body ground Ignition switch ON 11 to 14 V
    6. Connect the R5 forward recognition camera connector.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  6

  6. INSPECT FORWARD RECOGNITION CAMERA (WAVEFORM) 
    GTY869732Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Front view of wire harness connector
    (to Millimeter Wave Radar Sensor Assembly)    		 *b Waveform
    1. Turn the ignition switch off.
    2. Disconnect the B6 millimeter wave radar sensor assembly connector.
    3. Turn the ignition switch to ON.
    4. Using an oscilloscope, measure the waveform at the B6 millimeter wave radar sensor assembly connector.

      Measurement Condition

      Tester Connection Condition Tool Setting
      B6-5 (CA1P) - Body ground Ignition switch ON 1 V/DIV., 100 μs/DIV.
      NOTE:

      The oscilloscope waveform is for reference only and does not include noise, fluctuations, etc.

      OK

      A waveform similar to that in the illustration can be observed.

    5. Connect the B6 millimeter wave radar sensor assembly connector.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY. Refer to  REMOVAL [11/2023 - ] 

    Result: 

    NG 

    REPLACE FORWARD RECOGNITION CAMERA. Refer to  REMOVAL [11/2023 - ] 

Diesel-Data.com