DSD Information System
Home >> Toyota >> 2021 >> Highlander LE, 4WD >> Repair and Diagnosis >> Restraints >> Air Bag, SRS >> Airbag System - Diagnostic Codes (7 Of 7) & Symptom Tests >> Airbag System >> DTC B1925: Short in Rear P/T Squib (LH) Circuit; DTC B1926: Open in Rear P/T Squib (LH) Circuit; DTC B1927: Short in Rear P/T Squib (LH) Circuit (to Ground); DTC B1928: Short in Rear P/T Squib (LH) Circuit (to +B) [10/2021 - 11/2023] >> Procedure

DTC B1925: Short in Rear P/T Squib (LH) Circuit; DTC B1926: Open in Rear P/T Squib (LH) Circuit; DTC B1927: Short in Rear P/T Squib (LH) Circuit (to Ground); DTC B1928: Short in Rear P/T Squib (LH) Circuit (to +B) [10/2021 - 11/2023]: Procedure

  1. CHECK CONNECTORS 
    1. Turn the ignition switch off.
      GTY451104Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Rear Seat Outer Belt Assembly LH
      *2 Airbag Sensor Assembly
      *3 No. 2 Floor Wire
    2. Disconnect the cable from the negative (-) auxiliary battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the rear seat outer belt assembly LH and airbag sensor assembly.

      OK

      The connectors are properly connected.

      HINT: 

      If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the rear seat outer belt assembly LH and airbag sensor assembly.
    5. Check that the terminals of the connectors are not deformed or damaged.

      OK

      The terminals are not deformed or damaged.

    6. Check that the No. 2 floor wire connector (on the rear seat outer belt assembly LH side) is not loose, deformed or damaged.

      OK

      The airbag connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.

    7. Check that the short springs of the activation prevention mechanism of the No. 2 floor wire connector are not deformed or damaged.

      OK

      The short springs are not deformed or damaged.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE NO. 2 FLOOR WIRE 

    Result: 

    OK 

    See step  2

  2. CHECK REAR SEAT OUTER BELT ASSEMBLY LH 
    1. Connect the connector to the airbag sensor assembly.
      GTY1114873Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Rear Seat Outer Belt Assembly LH
      *2 Airbag Sensor Assembly
      *a Front view of wire harness connector
      (to Rear Seat Outer Belt Assembly LH)
    2. Connect SST (resistance 2.1 Ω) to connector C.
      WARNING:

      Never connect a tester to the rear seat outer belt assembly LH for measurement, as this may lead to a serious injury due to pretensioner deployment.

      NOTE:
      • Do not forcibly insert SST into the terminals of the connector when connecting it.
      • Insert SST straight into the terminals of the connector.
      • SST: 09843-18061 
    3. Connect the cable to the negative (-) auxiliary battery terminal.
    4. Turn the ignition switch to ON, and wait for at least 60 seconds.
    5. Clear the DTCs stored in memory.

      Body Electrical > SRS Airbag > Clear DTCs 

    6. Turn the ignition switch off.
    7. Turn the ignition switch to ON, and wait for at least 60 seconds.
    8. Check for DTCs.

      Body Electrical > SRS Airbag > Trouble Codes 

      OK

      DTC B1925, B1926, B1927 or B1928 is not output.

      HINT: 

      Codes other than DTCs B1925, B1926, B1927 and B1928 may be output at this time, but they are not related to this check.

    9. Turn the ignition switch off.
    10. Disconnect the cable from the negative (-) auxiliary battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    11. Disconnect SST from connector C.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE REAR SEAT OUTER BELT ASSEMBLY LH. Refer to  REMOVAL [10/2021 - 10/2022]  , or refer to  REMOVAL [10/2022 - 11/2023] 

    Result: 

    NG 

    See step  3

  3. CHECK NO. 2 FLOOR WIRE 
    1. Disconnect the No. 2 floor wire from the airbag sensor assembly.
      GTY1118265Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Rear Seat Outer Belt Assembly LH
      *2 Airbag Sensor Assembly
      *3 No. 2 Floor Wire
      *a Front view of wire harness connector
      (to Rear Seat Outer Belt Assembly LH)
    2. Check for a short to B+ in the circuit.
      1. Connect the cable to the negative (-) auxiliary battery terminal.
      2. Turn the ignition switch to ON.
      3. Measure the voltage according to the value(s) in the table below.

        Standard Voltage

        Tester Connection Condition Specified Condition
        M103-1 (RL+) - Body ground Ignition switch ON Below 1 V
        M103-2 (RL-) - Body ground Ignition switch ON Below 1 V
      4. Turn the ignition switch off.
      5. Disconnect the cable from the negative (-) auxiliary battery terminal.
        WARNING:

        Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check for an open in the circuit.
      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Condition
        M103-1 (RL+) - M103-2 (RL-) Always Below 1 Ω
    4. Check for a short to ground in the circuit.
      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Condition
        M103-1 (RL+) - Body ground Always 1 MΩ or higher
        M103-2 (RL-) - Body ground Always 1 MΩ or higher
    5. Check for a short in the circuit.
      1. Release the activation prevention mechanism built into connector B.

        Refer to SYSTEM DESCRIPTION [10/2021 - 11/2023]

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Condition
        M103-1 (RL+) - M103-2 (RL-) Always 1 MΩ or higher
      3. Restore the released activation prevention mechanism of connector B to the original condition.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE NO. 2 FLOOR WIRE 

    Result: 

    OK 

    See step  4

  4. CHECK DTC 
    1. Connect the connectors to the rear seat outer belt assembly LH and airbag sensor assembly.
      GTY437075Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Rear Seat Outer Belt Assembly LH
      *2 Airbag Sensor Assembly
    2. Connect the cable to the negative (-) auxiliary battery terminal.
    3. Turn the ignition switch to ON, and wait for at least 60 seconds.
    4. Clear the DTCs stored in memory.

      Body Electrical > SRS Airbag > Clear DTCs 

    5. Turn the ignition switch off.
    6. Turn the ignition switch to ON, and wait for at least 60 seconds.
    7. Check for DTCs.

      Body Electrical > SRS Airbag > Trouble Codes 

      OK

      DTC B1925, B1926, B1927 or B1928 is not output.

      HINT: 

      Codes other than DTCs B1925, B1926, B1927 and B1928 may be output at this time, but they are not related to this check.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [12/2019 - ] 

    Result: 

    NG 

    REPLACE AIRBAG SENSOR ASSEMBLY. Refer to  REMOVAL [12/2019 - 10/2022]  , or refer to  REMOVAL [10/2022 - 11/2023] 

Diesel-Data.com