Caution / Notice / Hint

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transfer assembly removal/installation are shown below.

NECESSARY PROCEDURES AFTER PARTS REMOVED/INSTALLED/REPLACED

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed	Link
Replacement of ECM	Perform Vehicle Identification Number (VIN) registration	DTC is output	Refer to REGISTRATION [10/2022 - ]
	Update ECU security key	Vehicle Control History (RoB) are stored	Refer to UPDATE ECU SECURITY KEY [11/2023 - ]
	Heavy knock history Save history Write history	-	Refer to REGISTRATION [10/2022 - ]
	Code registration	Engine start function	Refer to REGISTRATION [11/2023 - ]
	If transaxle compensation code read from ECM Perform reset memory*1 Transfer transaxle compensation code Perform road test to allow ECM to learn	Large shift shock Deterioration of fuel efficiency	for Initialization: Refer to INITIALIZATION [10/2022 - ] for Registration: Refer to REGISTRATION [10/2022 - ]
	If transaxle compensation code not read from ECM Perform reset memory*1 Reset transaxle compensation code Perform road test to allow ECM to learn	Large shift shock Deterioration of fuel efficiency
Replacement of engine assembly Gas leak from exhaust system is repaired	Inspection after repair	Poor idle, etc. Engine start function, etc.	Refer to INITIALIZATION [10/2022 - ]
Replacement of starter assembly*2	Clear the number of starter operations	Stop and Start System	Refer to REGISTRATION [11/2023 - ]
Replacement of battery	Integrated Current Value Initialization Switch Battery Type	Stop and Start System	Refer to REGISTRATION [11/2023 - ]
Replacement of automatic transaxle assembly	Perform reset memory Input transaxle compensation code into ECM Perform road test to allow ECM to learn	Large shift shock Deterioration of fuel efficiency	for Initialization: Refer to INITIALIZATION [10/2022 - ] for Registration: Refer to REGISTRATION [10/2022 - ]
Replacement of automatic transaxle fluid	ATF thermal degradation estimate reset	The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly	Refer to INITIALIZATION [10/2022 - ]
Replacement of front 4WD linear solenoid (Transfer assembly)	ECU data initialization Disconnect system function check	Dynamic Torque Control AWD System	Refer to CALIBRATION [12/2019 - ]
	ECU data initialization Disconnect system function check	Dynamic Torque Vectoring AWD System	Refer to CALIBRATION [12/2019 - ]
Front wheel alignment adjustment	Perform "Reset Memory". Perform "Calibration".	VSC is disabled or malfunctions DTCs are output Slip indicator light illuminates ABS warning light illuminates	Refer to UTILITY [11/2023 - ]
Suspension, tires, etc.*3	Rear television camera assembly optical axis (Back camera position setting)	Parking Assist Monitor System	Refer to CALIBRATION [10/2022 - ]
	Parking assist ECU initialization	Panoramic View Monitor System	Refer to CALIBRATION [11/2023 - ]
	w/ AFS: Perform headlight ECU sub-assembly LH initialization	Lighting System (EXT) (w/ AFS)	Refer to INITIALIZATION [11/2023 - ]
Replacement of front bumper assembly*	Front television camera view adjustment	Panoramic View Monitor System	Refer to CALIBRATION [11/2023 - ]

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Not necessary when ECM replaced with new one

*2: When the starter assembly is replaced, "ST relay" must be also replaced

*3: If the vehicle height has changed due to suspension or tire replacement

WARNING:

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair information, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	An Object Exceeding Weight Limit of Engine Lifter

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

The automatic transaxle assembly is very heavy. Be sure to follow the procedure described in the repair information, or the transmission jack may suddenly drop.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	An Object Exceeding Weight Limit of Transmission Jack

NOTE:

If the ECM has been struck or dropped, replace it.

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

LEARNING COMPLETES WHEN VEHICLE IS DRIVEN

Effect/Inoperative Function when Necessary Procedure not Performed	Necessary Procedures	Link
Stop and Start System	Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted	Refer to PRECAUTION [11/2023 - ]
Lane Control System	Perform steering sensor zero point calibration	Refer to INITIALIZATION [12/2019 - ]
Pre-collision System
Lighting System (EXT) (w/ AFS)

LEARNING COMPLETES WHEN VEHICLE IS OPERATED NORMALLY

Effect/Inoperative Function when Necessary Procedure not Performed	Necessary Procedures	Link
Power Door Lock Control System	Initialize back door lock	Refer to INITIALIZATION [11/2023 - ]
Power Back Door System	Reset back door close position	Refer to INITIALIZATION [11/2023 - ]
Air Conditioning System	After the ignition switch is turned to ON, the servo motor standard position is recognized.	-