DSD Information System
Home >> Toyota >> 2021 >> Highlander LE, 4WD >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Collision/Avoidance >> Panoramic View Monitor System - Diagnostics - Introduction (2 Of 2) >> Panoramic View Monitor System >> Data List / Active Test [12/2019 - 10/2022] >> Data List / Active Test [12/2019 - 10/2022]

Data List / Active Test [12/2019 - 10/2022]

  1. DATA LIST 
    NOTE:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    HINT: 

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    1. Connect the GTS to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the GTS on.
    4. Enter the following menus: Chassis / Circumference Monitoring Camera Control Module / Data List.
    5. Read the Data List according to the display on the GTS.

      Chassis > Circumference Monitoring Camera Control Module > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      HV/EV/ENG Data Check Verification of the HV/ENG data OK/NG OK: Data verification normal
      NG: Data verification abnormal      		 -
      2WD/4WD Data Check Verification of the 2WD/4WD data OK/NG OK: Data verification normal
      NG: Data verification abnormal      		 -
      Main CPU Forced Termination Detection Record A history item indicating that the main CPU did not enter standby status within 15 seconds of turning the ignition switch off and a forced end was applied Unrec/Rec Unrec: Parking assist ECU is normal
      Rec: Parking assist ECU is abnormal      		 -
      Main CPU Abnormal Response Record A history item indicating that the main CPU became unresponsive in normal status Unrec/Rec Unrec: Parking assist ECU is normal
      Rec: Parking assist ECU is abnormal      		 -
      Main CPU Abnormal Reset Record A history item indicating that the main CPU was reset, although the ignition switch was not turned off in normal status Unrec/Rec Unrec: Parking assist ECU is normal
      Rec: Parking assist ECU is abnormal      		 -
      Image Processing IC Written Protect Record A history item indicating that the image processing IC memory was write protected Unrec/Rec Unrec: Parking assist ECU is normal
      Rec: Parking assist ECU is abnormal      		 -
      Image Processing IC Initialized Malfunction Record A history item indicating that the image processing IC memory was not initialized Unrec/Rec Unrec: Parking assist ECU is normal
      Rec: Parking assist ECU is abnormal      		 -
      Main EEPROM Access Status Main EEPROM access status OK/NG OK: Parking assist ECU is normal
      NG: Parking assist ECU is abnormal      		 -
      Sub EEPROM Access Status Sub-EEPROM access status OK/NG OK: Parking assist ECU is normal
      NG: Parking assist ECU is abnormal      		 -
      System Power Supply Voltage Malfunction Record A history item indicating an abnormally generated-voltage value from the system power source Unrec/Rec Unrec: Parking assist ECU is normal
      Rec: Parking assist ECU is abnormal      		 -
      Main CPU Starting Malfunction Record A history item indicating that the main CPU did not start Unrec/Rec Unrec: Parking assist ECU is normal
      Rec: Parking assist ECU is abnormal      		 -
      CAN CPU Boot Malfunction Record A history item indicating that the CPU controlling the input and output of the information obtained via the CAN communication system did not start and the information could not be retrieved Unrec/Rec Unrec: Parking assist ECU is normal
      Rec: Parking assist ECU is abnormal      		 -
      Visual Display Line Status Displays the status of the video signals displayed on the multi-display OK/NG OK: GVIF cable is normal
      NG: GVIF cable is abnormal      		 -
      Wheel Speed Sensor (4wheel) Reception state of the vehicle speed signal from the skid control ECU*1, No. 2 skid control ECU*2 OK/NG OK: Speed signal received
      NG: Speed signal not received      		 -
      Continuous Bus Off Continuous bus off status (Global) Not Detected/Detected Not detected: Communication condition available
      Detected: Communication condition not available      		 -
      Sending CAN Message Communication condition from parking assist ECU (Global) OK/NG OK: Communication condition available
      NG: Communication condition not available      		 -
      Shift R Position Reverse signal ON/OFF OFF: Shift lever in any position except R
      ON: Shift lever in R      		 -
      Camera Changing SW Signal Status Signal status at the BLSW terminal (switch camera signal) ON/OFF ON: Panoramic view monitor main switch on
      OFF: Panoramic view monitor main switch off      		 -
      Back Camera Availability Consistency Status of ECU stored in rear television camera assembly OK/NG OK: Normal
      NG: Rear television camera assembly or parking assist ECU is abnormal      		 -
      Image Adjustment Status Status of the image adjustment status Incomplete/Processing/Complete Incomplete: Image adjustment incomplete
      Processing: Image adjustment in processing
      Complete: Image adjustment completed      		 -
      Number of DTC Number of DTCs (past and present) Min: 0, Max: 255 Number of DTCs will be displayed -
      1. *1: for Gasoline Model

        *2: for HV Model

Diesel-Data.com