How To Proceed With Troubleshooting [10/2022 - ]: Procedure
- VEHICLE BROUGHT TO WORKSHOP
Result
Proceed to NEXT Result:
NEXT
See step 2
- CUSTOMER PROBLEM ANALYSIS
- Ask the customer about the problems and the conditions at the time the malfunction occurred to make sure the problem symptom was not temporarily caused by radio waves in the surrounding environment.
HINT:
The parking assist monitor display may be temporarily distorted due to radio waves around the vehicle.
Problem Symptom Cause The problem symptom indicates a parking assist monitor display malfunction and the problem symptom cannot be reproduced. The display may be temporarily distorted when the vehicle is close to an object that transmits radio waves, such as a telecommunication tower, an airport or a truck equipped with a transceiver. Result
Proceed to NEXT
Result:
NEXT
See step 3
- Ask the customer about the problems and the conditions at the time the malfunction occurred to make sure the problem symptom was not temporarily caused by radio waves in the surrounding environment.
- INSPECT AUXILIARY BATTERY VOLTAGE
- Measure the auxiliary battery voltage with the ignition switch off.
Standard voltage
11 to 14 V
If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding to the next step.
Result
Proceed to NEXT
Result:
NEXT
See step 4
- Measure the auxiliary battery voltage with the ignition switch off.
- CHECK AUDIO AND VISUAL SYSTEM
- Refer to the audio and visual system.
Refer to PROBLEM SYMPTOMS TABLE [10/2022 - 11/2024] , or refer to PROBLEM SYMPTOMS TABLE [11/2024 - ]
Result
Result Proceed to Audio and visual system is normal A Audio and visual system is abnormal B
Result:
B
GO TO AUDIO AND VISUAL SYSTEM
Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2022 - ]
Result:
A
See step 5
- Refer to the audio and visual system.
- CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
- Use the GTS to check if the CAN communication system is functioning normally.
HV Model: Refer to DIAGNOSIS SYSTEM [10/2022 - 11/2023] , or refer to DIAGNOSIS SYSTEM [11/2023 - ]
Gasoline Model: Refer to DIAGNOSIS SYSTEM [10/2022 - 11/2023] , or refer to DIAGNOSIS SYSTEM [11/2023 - ]
Result
Result Proceed to CAN communication system DTCs are not output A CAN communication system DTCs are output B
Result:
B
GO TO CAN COMMUNICATION SYSTEM
HV Model: Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2022 - 11/2023] , or refer to HOW TO PROCEED WITH TROUBLESHOOTING [11/2023 - ]
Gasoline Model: Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2022 - 11/2023] , or refer to HOW TO PROCEED WITH TROUBLESHOOTING [11/2023 - ]
Result:
A
See step 6
- Use the GTS to check if the CAN communication system is functioning normally.
- CHECK FOR DTC*
- Check for DTCs and make a note of any codes that are output.
Chassis > Rear Camera > Trouble Codes
Body Electrical > Navigation System > Trouble Codes
- Clear the DTCs.
Chassis > Rear Camera > Clear DTCs
Body Electrical > Navigation System > Clear DTCs
- Recheck for DTCs. Try to reproduce the problem symptoms based on the recorded DTCs, and then check if the DTCs are output again.
Chassis > Rear Camera > Trouble Codes
Body Electrical > Navigation System > Trouble Codes
Result
Result Proceed to No DTCs are output A DTCs are output B
Result:
B
GO TO DIAGNOSTIC TROUBLE CODE CHART
Refer to DIAGNOSTIC TROUBLE CODE CHART [10/2022 - 11/2023] , or refer to DIAGNOSTIC TROUBLE CODE CHART [11/2023 - ]
Result:
A
See step 7
- Check for DTCs and make a note of any codes that are output.
- CHECK FOR VEHICLE CONTROL HISTORY*
HINT:
Refer to Vehicle Control History.
Refer to VEHICLE CONTROL HISTORY (RoB) [10/2022 - 11/2023] , or refer to VEHICLE CONTROL HISTORY (RoB) [11/2023 - ]
- Check for vehicle control history and note any codes that are output.
Chassis > Rear Camera > Utility
Tester Display Vehicle Control History (RoB) Result
Result Proceed to No vehicle control history is output A Vehicle control history is output B
Result:
B
GO TO VEHICLE CONTROL HISTORY
Refer to VEHICLE CONTROL HISTORY (RoB) [10/2022 - 11/2023] , or refer to VEHICLE CONTROL HISTORY (RoB) [11/2023 - ]
Result:
A
See step 8
- Check for vehicle control history and note any codes that are output.
- PROBLEM SYMPTOMS TABLE
- Refer to Problem Symptoms Table.
Refer to PROBLEM SYMPTOMS TABLE [10/2022 - ]
Result
Result Proceed to Fault is not listed in Problem Symptoms Table A Fault is listed in Problem Symptoms Table B
Result:
B
See step 10
Result:
A
See step 9
- Refer to Problem Symptoms Table.
- OVERALL ANALYSIS AND TROUBLESHOOTING*
- Diagnosis System
Refer to DIAGNOSIS SYSTEM [10/2022 - ]
- Terminals of ECU
Refer to TERMINALS OF ECU [10/2022 - 11/2023] , or refer to TERMINALS OF ECU [11/2023 - ]
- Data List / Active Test
Refer to DATA LIST / ACTIVE TEST [10/2022 - ]
Result
Proceed to NEXT
Result:
NEXT
See step 10
- Diagnosis System
- ADJUST, REPAIR OR REPLACE
Result
Proceed to NEXT Result:
NEXT
See step 11
- CONFIRMATION TEST
Result
Proceed to NEXT Result:
NEXT
END