Data List / Active Test [12/2019 - 11/2023]
- DATA LIST NOTE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- Connect the GTS to the DLC3.
- Turn the ignition switch to ON.
- Turn the GTS on.
- Enter the following menus: Body Electrical / Clearance Warning / Data List.
- Read the Data List according to the display on the GTS.
Body Electrical > Clearance Warning > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note Ultrasonic Sensor (Front Left Center) Target Distance - First Wave Distance from the ultrasonic sensor to the target Unknown/Not Detected/0 to 7.65 m Unknown: Outside sensor operation conditions
Not detected: Not detected
0 to 7.65 m: Detected distance- Ultrasonic Sensor (Front Left Center) Target Distance - Second Wave Distance from the ultrasonic sensor to the target Unknown/Not Detected/0 to 7.65 m Unknown: Outside sensor operation conditions
Not detected: Not detected
0 to 7.65 m: Detected distance- Ultrasonic Sensor (Front Right Center) Target Distance - First Wave Distance from the ultrasonic sensor to the target Unknown/Not Detected/0 to 7.65 m Unknown: Outside sensor operation conditions
Not detected: Not detected
0 to 7.65 m: Detected distance- Ultrasonic Sensor (Front Right Center) Target Distance - Second Wave Distance from the ultrasonic sensor to the target Unknown/Not Detected/0 to 7.65 m Unknown: Outside sensor operation conditions
Not detected: Not detected
0 to 7.65 m: Detected distance- Ultrasonic Sensor (Front Left Corner) Target Distance - First Wave Distance from the ultrasonic sensor to the target Unknown/Not Detected/0 to 7.65 m Unknown: Outside sensor operation conditions
Not detected: Not detected
0 to 7.65 m: Detected distance- Ultrasonic Sensor (Front Left Corner) Target Distance - Second Wave Distance from the ultrasonic sensor to the target Unknown/Not Detected/0 to 7.65 m Unknown: Outside sensor operation conditions
Not detected: Not detected
0 to 7.65 m: Detected distance- Ultrasonic Sensor (Front Right Corner) Target Distance - First Wave Distance from the ultrasonic sensor to the target Unknown/Not Detected/0 to 7.65 m Unknown: Outside sensor operation conditions
Not detected: Not detected
0 to 7.65 m: Detected distance- Ultrasonic Sensor (Front Right Corner) Target Distance - Second Wave Distance from the ultrasonic sensor to the target Unknown/Not Detected/0 to 7.65 m Unknown: Outside sensor operation conditions
Not detected: Not detected
0 to 7.65 m: Detected distance- Ultrasonic Sensor (Rear Left Center) Target Distance - First Wave Distance from the ultrasonic sensor to the target Unknown/Not Detected/0 to 7.65 m Unknown: Outside sensor operation conditions
Not detected: Not detected
0 to 7.65 m: Detected distance- Ultrasonic Sensor (Rear Left Center) Target Distance - Second Wave Distance from the ultrasonic sensor to the target Unknown/Not Detected/0 to 7.65 m Unknown: Outside sensor operation conditions
Not detected: Not detected
0 to 7.65 m: Detected distance- Ultrasonic Sensor (Rear Right Center) Target Distance - First Wave Distance from the ultrasonic sensor to the target Unknown/Not Detected/0 to 7.65 m Unknown: Outside sensor operation conditions
Not detected: Not detected
0 to 7.65 m: Detected distance- Ultrasonic Sensor (Rear Right Center) Target Distance - Second Wave Distance from the ultrasonic sensor to the target Unknown/Not Detected/0 to 7.65 m Unknown: Outside sensor operation conditions
Not detected: Not detected
0 to 7.65 m: Detected distance- Ultrasonic Sensor (Rear Left Corner) Target Distance - First Wave Distance from the ultrasonic sensor to the target Unknown/Not Detected/0 to 7.65 m Unknown: Outside sensor operation conditions
Not detected: Not detected
0 to 7.65 m: Detected distance- Ultrasonic Sensor (Rear Left Corner) Target Distance - Second Wave Distance from the ultrasonic sensor to the target Unknown/Not Detected/0 to 7.65 m Unknown: Outside sensor operation conditions
Not detected: Not detected
0 to 7.65 m: Detected distance- Ultrasonic Sensor (Rear Right Corner) Target Distance - First Wave Distance from the ultrasonic sensor to the target Unknown/Not Detected/0 to 7.65 m Unknown: Outside sensor operation conditions
Not detected: Not detected
0 to 7.65 m: Detected distance- Ultrasonic Sensor (Rear Right Corner) Target Distance - Second Wave Distance from the ultrasonic sensor to the target Unknown/Not Detected/0 to 7.65 m Unknown: Outside sensor operation conditions
Not detected: Not detected
0 to 7.65 m: Detected distance- PKSB Main Switch Input signal for parking support brake system ON/OFF ON: Parking support brake system ON
OFF: Parking support brake system OFF- PKSB (O) Function Status of parking support brake (static objects) function ON/OFF ON: Parking support brake (static objects) function ON
OFF: Parking support brake (static objects) function OFF- PKSB (O) Target Stopping Distance Target stop distance setting status of parking support brake (static objects) function Close/Far Setting of customized parameter - PKSB Switch State Stored Setting of the parking support brake system main switch status memory Stored/Not stored Setting of customized parameter - PKSB (V) Function Status of parking support brake (rear crossing vehicles) function ON/OFF ON: Parking support brake (rear crossing vehicles) function ON
OFF: Parking support brake (rear crossing vehicles) function OFF- PKSB Detection Area Adjustment Incomplete Adjustment status of ultrasonic sensor Adjusted/Not Adjusted Adjusted: Ultrasonic sensor adjustment complete
Not Adjusted: Ultrasonic sensor adjustment not complete-
- ACTIVE TEST
HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
- Connect the GTS to the DLC3.
- Turn the ignition switch to ON.
- Turn the GTS on.
- Enter the following menus: Chassis / Brake/EPB / Active Test.
Chassis > Brake/EPB > Active Test
Tester Display Measurement Item Control Range Diagnostic Note Stop Lamp Relay Stop lights ON / OFF Test possible at vehicle speed of 0 km/h (0 mph) - According to the display on the GTS, perform the Active Test.
- Enter the following menus: Body Electrical / Combination Meter / Active Test.
- According to the display on the GTS, perform the Active Test.
Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note ICS OFF Warning Combination meter assembly ON / OFF - - Enter the following menus: Body Electrical /Clearance Warning / Active Test.
- According to the display on the GTS, perform the Active Test.
Body Electrical > Clearance Warning > Active Test
Tester Display Measurement Item Control Range Diagnostic Note Front Buzzer No. 1 clearance warning buzzer Stop or Operate Confirm that the vehicle is stopped and the ignition switch is ON Rear Buzzer No. 2 clearance warning buzzer Stop or Operate Confirm that the vehicle is stopped and the ignition switch is ON