DSD Information System
Home >> Toyota >> 2021 >> Highlander LE, 4WD >> Repair and Diagnosis >> Accessories & Equipment >> Wiper/Washer Systems >> Wiper System / Washer System - Diagnostics - Introduction >> Wiper And Washer System >> Precaution [11/2023 - ] >> Precaution [11/2023 - ]

Precaution [11/2023 - ]

  1. PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL 
    NOTE:
    • After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 2 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
    • When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal.
  2. AUTOMATIC LEARNING PERFORMED WHEN CABLE IS DISCONNECTED / RECONNECTED TO AUXILIARY BATTERY TERMINAL 

    When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

    LEARNING COMPLETES WHEN VEHICLE IS DRIVEN

    Effect/Inoperative Function when Necessary Procedure not Performed Necessary Procedure Link
    Stop and Start System Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted Refer to PRECAUTION [11/2023 - ]
    Lane Control System Perform steering sensor zero point calibration Refer to INITIALIZATION [12/2019 - ]
    Pre-collision System
    Lighting System (EXT) (w/ AFS)
    LEARNING COMPLETES WHEN VEHICLE IS OPERATED NORMALLY

    Effect/Inoperative Function when Necessary Procedure not Performed Necessary Procedure Link
    Power Door Lock Control System Initialize back door lock Refer to INITIALIZATION [11/2023 - ]
    Power Back Door System Reset back door close position Refer to INITIALIZATION [11/2023 - ]
    Air Conditioning System After the ignition switch is turned to ON, the servo motor standard position is recognized. -
  3. PRECAUTION FOR WASHER NOZZLE ADJUSTMENT 
    1. Do not clean or adjust the washer nozzle with a safety pin, etc. because:
      1. The washer nozzle tip is made of resin and may be damaged.
      2. Adjustment is not necessary for this spray type washer nozzle. If it is necessary to change the nozzle angle, replace the washer nozzle with one that has a different nozzle angle.

        Refer to ADJUSTMENT [12/2019 - ]

    2. If the washer nozzle is clogged with wax, etc., remove it and clean the nozzle hole with a soft resin brush or other cleaning tool.
  4. PRECAUTIONS FOR RAIN SENSOR (w/ Auto Wiper System) 
    1. When the ignition switch is ON and the front wiper switch is in the AUTO position, the rain sensor may operate the front wipers if the rain sensor sensing portion of the windshield glass is touched by a hand or if something moist, such as a wet cloth, is brought near. This may lead to injury or damage to the vehicle.
    2. When the ignition switch is ON and the front wiper switch is in the AUTO position, the rain sensor may operate the wipers if the rain sensor or parts around the rain sensor (windshield glass, rain sensor cover, etc.) are vibrated.
    3. If the windshield glass is coated with a water-repellent coating, the rain sensor may not correctly detect the amount of raindrops that strike the windshield and the auto wiper system may not operate normally.
    4. As the rain sensor is an optical sensor, if sunlight intermittently strikes the windshield glass or the rain sensor sensing portion of the windshield glass is dirty, the auto wiper system may not operate normally.
    5. The rain sensor cannot operate if the front wipers are stopped in any position other than the park position.
Diesel-Data.com