DSD Information System
Home >> Toyota >> 2021 >> Highlander LE, 4WD >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Communication Devices >> Can Communication System (Except HV) - Circuit Tests (1 Of 8) & Diagnostic Codes >> CAN COMMUNICATION SYSTEM (for Gasoline Model) >> Clearance Warning ECU Communication Stop Mode [11/2023 - ] >> Procedure

Clearance Warning ECU Communication Stop Mode [11/2023 - ]: Procedure

  1. CHECK FOR OPEN IN CAN BUS LINES (CLEARANCE WARNING ECU ASSEMBLY BRANCH LINE) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the H46 clearance warning ECU assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      H46-17 (R1) - H46-18 (R2) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      GTY1177790Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Clearance Warning ECU Assembly)

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY) 

    Result: 

    OK 

    See step  2

  2. CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      H46-31 (E) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
      GTY1178353Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Clearance Warning ECU Assembly)

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT) 

    Result: 

    OK 

    See step  3

  3. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      w/ Stop and Start System A
      w/o Stop and Start System B

    Result: 

    B 

    See step  5

    Result: 

    A 

    See step  4

  4. CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT) 
    1. Reconnect the cable to the negative (-) battery terminal.
    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      H46-1 (IG) - Body ground Ignition switch ON 10.5 to 16 V
      GTY1178352Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Clearance Warning ECU Assembly)

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE CLEARANCE WARNING ECU ASSEMBLY 

    Refer to REMOVAL [11/2023 - ]

    Result: 

    NG 

    GO TO STOP AND START SYSTEM (FOR BACKUP BOOST CONVERTER CIRCUIT) 

    Refer to Backup Boost Converter Circuit [11/2023 - ]

  5. CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT) 
    1. Reconnect the cable to the negative (-) battery terminal.
    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      H46-1 (IG) - Body ground Ignition switch ON 11 to 14 V
      GTY919040Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Clearance Warning ECU Assembly)

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE CLEARANCE WARNING ECU ASSEMBLY 

    Refer to REMOVAL [11/2023 - ]

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT) 

Diesel-Data.com