DSD Information System
Home >> Toyota >> 2021 >> Highlander LE, 4WD >> Repair and Diagnosis >> Electrical >> Gauges >> Meter / Gauge System (Except 12.3 Inch Display) - Diagnostics - Introduction (4 Of 4) >> METER / GAUGE SYSTEM (except 12.3 Inch Display) >> Data List / Active Test [10/2022 - 11/2023] >> Data List / Active Test [10/2022 - 11/2023]

Data List / Active Test [10/2022 - 11/2023]

  1. DATA LIST 
    NOTE:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    HINT: 

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    1. Connect the GTS to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the GTS on.
    4. Enter the following menus:
      • Body Electrical / Combination Meter / Data List.
      • Chassis / Brake/EPB / Data List.
      • Powertrain / Engine / Data List.
      • Body Electrical / Main Body / Data List.
    5. Read the Data List according to the display on the GTS.
      1. Combination Meter
        NOTE:

        Depending on the vehicle specifications, some of the Data List items in the following table will not be displayed on the GTS.

        Body Electrical > Combination Meter > Data List 

        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        ODO/TRIP Change Switch ODO/TRIP switch OFF or ON OFF: Switch released
        ON: Switch pushed        		 When the switch is built into the combination meter assembly or is connected via direct line, the input value is displayed.
        Trip Reset Switch Trip reset switch OFF or ON OFF: Switch released
        ON: Switch pushed        		 When the switch is built into the combination meter assembly or is connected via direct line, the input value is displayed.
        Multi Display Select Switch DISP switch OFF or ON OFF: Switch released
        ON: Switch pushed        		 When the switch is built into the combination meter assembly or is connected via direct line, the input value is displayed.
        Meter Day Mode Switch Tail cancel switch OFF or ON OFF: Switch released
        ON: Switch pushed        		 When the switch is built into the combination meter assembly or is connected via direct line, the input value is displayed.
        Light Control Switch (UP) Light control rheostat up switch OFF or ON OFF: Switch released
        ON: Switch pushed        		 When the switch is built into the combination meter assembly or is connected via direct line, the input value is displayed.
        Light Control Switch (DOWN) Light control rheostat down switch OFF or ON OFF: Switch released
        ON: Switch pushed        		 When the switch is built into the combination meter assembly or is connected via direct line, the input value is displayed.
        Light Control Switch (Single) Light control rheostat switch OFF or ON OFF: Switch released
        ON: Switch pushed        		 When the switch is built into the combination meter assembly or is connected via direct line, the input value is displayed.
        Timer Switch H on Combination Meter Clock switch (H) OFF or ON OFF: Switch released
        ON: Switch pushed        		 When the switch is built into the combination meter assembly or is connected via direct line, the input value is displayed.
        Timer Switch M on Combination Meter Clock switch (M) OFF or ON OFF: Switch released
        ON: Switch pushed        		 When the switch is built into the combination meter assembly or is connected via direct line, the input value is displayed.
        Timer Switch 00 on Combination Meter Clock switch (00) OFF or ON OFF: Switch released
        ON: Switch pushed        		 When the switch is built into the combination meter assembly or is connected via direct line, the input value is displayed.
        Timer Switch on Combination Meter Clock switch OFF or ON OFF: Switch released
        ON: Switch pushed        		 When the switch is built into the combination meter assembly or is connected via direct line, the input value is displayed.
        Multi Switch (Up) Up switch on steering pad switch OFF or ON OFF: Switch released
        ON: Switch pushed        		 When the switch is built into the combination meter assembly or is connected via direct line, the input value is displayed.
        Multi Switch (Down) Down switch on steering pad switch OFF or ON OFF: Switch released
        ON: Switch pushed        		 When the switch is connected via direct line, the input value is displayed.
        Multi Switch (Left) Left switch on steering pad switch OFF or ON OFF: Switch released
        ON: Switch pushed        		 When the switch is connected via direct line, the input value is displayed.
        Multi Switch (Right) Right switch on steering pad switch OFF or ON OFF: Switch released
        ON: Switch pushed        		 When the switch is connected via direct line, the input value is displayed.
        Multi Switch (Enter) OK switch on steering pad switch OFF or ON OFF: Switch released
        ON: Switch pushed        		 When the switch is connected via direct line, the input value is displayed.
        Multi Switch (Back) Back switch on steering pad switch OFF or ON OFF: Switch released
        ON: Switch pushed        		 When the switch is connected via direct line, the input value is displayed.
        Multi Switch (Menu) Menu switch on steering pad switch OFF or ON OFF: Switch released
        ON: Switch pushed        		 When the switch is connected via direct line, the input value is displayed.
        +B Voltage Auxiliary battery voltage Min.: 0.0 V, Max.: 25.5 V or Unset 11 to 14 V -
        Fuel Input Fuel level gauge output Min.: 0.00 L, Max.: 655.35 L or Unset for HV Model 
        • Fuel receiver gauge indicates F: 56.44 L
        • Fuel receiver gauge indicates 3/4: 48.32 L
        • Fuel receiver gauge indicates 1/2: 32.25 L
        • Fuel receiver gauge indicates 1/4: 16.13 L
        • Fuel receiver gauge indicates E: 6.45 L

        for Gasoline Model 

        • Fuel receiver gauge indicates F: 60.93 L
        • Fuel receiver gauge indicates 3/4: 50.78 L
        • Fuel receiver gauge indicates 1/2: 33.85 L
        • Fuel receiver gauge indicates 1/4: 16.93 L
        • Fuel receiver gauge indicates E: 7.74 L
        		 -
        Sub Fuel Input Sub fuel level gauge output Min.: 0.00 L, Max.: 655.35 L or Unset Current fuel level displayed -
        Rheostat value Light control rheostat switch input Min.: 0.00%, Max.: 100.01% or Unset Increases from 0 to 100 as light control rheostat switch (trip switch) turned from left to right When the switch is not connected to the combination meter assembly via direct line, the value of the Data List item will not change.
        Vehicle Speed Meter Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) or Unset Almost the same as actual speedometer -
        Engine RPM Engine speed Min.: 0 rpm, Max.: 12701 rpm or Unset Almost the same as actual tachometer -
        Washer Level Warning Switch Washer fluid level warning switch OFF or ON OFF: Washer fluid level not low
        ON: Washer fluid level low        		 When the switch is not connected to the combination meter assembly via direct line, the value of the Data List item will not change.
        Driver Buckle Switch Seat belt buckle switch
        (for Driver seat)        		 Fastened or Not Fastened Fastened: Driver seat belt buckle switch fastened
        Not Fastened: Driver seat belt buckle switch unfastened        		 When the switch is not connected to the combination meter assembly via direct line, the value of the Data List item will not change.
        Passenger Buckle Switch Seat belt buckle switch
        (for Front passenger seat)        		 Fastened or Not Fastened Fastened: Front passenger seat belt buckle switch fastened
        Not Fastened: Front passenger seat belt buckle switch unfastened        		 When the switch is not connected to the combination meter assembly via direct line, the value of the Data List item will not change.
        (The occupant detection sensor circuit and buckle switch circuit are separate.)
        Passenger Occupant Detection Switch Occupant detection sensor
        (for Front passenger seat)        		 OFF or ON OFF: Front passenger seat not occupied
        ON: Front passenger seat occupied        		 When the switch is not connected to the combination meter assembly via direct line, the value of the Data List item will not change.
        (The occupant detection sensor circuit and buckle switch circuit are separate.)
        Passenger Buckle / Occupant Detection Warning Switch Seat belt buckle switch and occupant detection sensor
        (for Front passenger seat)        		 OFF or ON OFF: Front passenger seat belt fastened or front passenger seat not occupied
        ON: Front passenger seat belt unfastened and front passenger seat occupied        		 When the switch is not connected to the combination meter assembly via direct line, the value of the Data List item will not change.
        (The occupant detection sensor circuit and buckle switch circuit are the same.)
        Rear Right Seat Buckle / Occupant Detection Warning Switch Seat belt buckle switch
        (for Rear No. 1 right seat)        		 OFF or ON OFF: Rear No. 1 seat belt RH fastened
        ON: Rear No. 1 seat belt RH unfastened        		 When the switch is not connected to the combination meter assembly via direct line, the value of the Data List item will not change.
        Rear Left Seat Buckle / Occupant Detection Warning Switch Seat belt buckle switch
        (for Rear No. 1 left seat)        		 OFF or ON OFF: Rear No. 1 seat belt LH fastened
        ON: Rear No. 1 seat belt LH unfastened        		 When the switch is not connected to the combination meter assembly via direct line, the value of the Data List item will not change.
        Rear Center Seat Buckle / Occupant Detection Warning Switch Seat belt buckle switch
        (for Rear No. 1 center seat)        		 OFF or ON OFF: Rear No. 1 seat belt center fastened
        ON: Rear No. 1 seat belt center unfastened        		 When the switch is not connected to the combination meter assembly via direct line, the value of the Data List item will not change.
        3rd Right Seat Buckle / Occupant Detection Warning Switch Seat belt buckle switch
        (for Rear No. 2 right seat)        		 OFF or ON OFF: Rear No. 2 seat belt RH fastened
        ON: Rear No. 2 seat belt RH unfastened        		 When the switch is not connected to the combination meter assembly via direct line, the value of the Data List item will not change.
        3rd Left Seat Buckle / Occupant Detection Warning Switch Seat belt buckle switch
        (for Rear No. 2 left seat)        		 OFF or ON OFF: Rear No. 2 seat belt LH fastened
        ON: Rear No. 2 seat belt LH unfastened        		 When the switch is not connected to the combination meter assembly via direct line, the value of the Data List item will not change.
        3rd Center Seat Buckle / Occupant Detection Warning Switch Seat belt buckle switch
        (for Rear No. 2 center seat)        		 OFF or ON OFF: Rear No. 2 seat belt center fastened
        ON: Rear No. 2 seat belt center unfastened        		 When the switch is not connected to the combination meter assembly via direct line, the value of the Data List item will not change.
        Turn Signal Switch (Left) LH turn signal switch OFF or ON OFF: LH turn signal switch off
        ON: LH turn signal switch on        		 When the switch is not connected to the combination meter assembly via direct line, the value of the Data List item will not change.
        Turn Signal Switch (Right) RH turn signal switch OFF or ON OFF: RH turn signal switch off
        ON: RH turn signal switch on        		 When the switch is not connected to the combination meter assembly via direct line, the value of the Data List item will not change.
        Turn Switch Signal (Full Turn) Turn signal switch signal OFF or ON OFF: LH and RH turn signal switch off
        ON: LH or RH turn signal switch on        		 When the switch is not connected to the combination meter assembly via direct line, the value of the Data List item will not change.
        Hazard Flasher Switch Hazard warning signal switch OFF or ON OFF: Hazard warning signal switch off
        ON: Hazard warning signal switch on        		 When the switch is not connected to the combination meter assembly via direct line, the value of the Data List item will not change.
        Ambient Temperature (Celsius) Outside temperature
        (Celsius)        		 Min.: -40.0°C, Max.: 87.1°C or Unset Almost the same as actual outside temperature -
        Ambient Temperature (Fahrenheit) Outside temperature
        (Fahrenheit)        		 Min.: -40°F, Max.: 215°F or Unset Almost the same as actual outside temperature -
        Lighting System Existence of headlight ECU Without or With Without: w/o Headlight ECU
        With: w/ Headlight ECU        		 -
        Back Door System Existence of power back door system Without or With Without: w/o Power Back Door System
        With: w/ Power Back Door System        		 -
        Oil Pressure Switch Engine oil pressure switch OFF or ON OFF: Engine started
        ON: Engine not started        		 When the switch is not connected to the combination meter assembly via direct line, the value of the Data List item will not change.
        Oil Level Switch Engine oil level sensor OFF or ON OFF: Engine oil level not low
        ON: Engine oil level low        		 When the switch is not connected to the combination meter assembly via direct line, the value of the Data List item will not change.
        Water Level Switch Fuel sediment switch OFF or ON OFF: Less than a large amount of water in fuel
        ON: Large amount of water in fuel        		 When the switch is not connected to the combination meter assembly via direct line, the value of the Data List item will not change.
        Fuel Filter Switch Fuel filter warning signal OFF or ON OFF: Fuel filter warning light off
        ON: Fuel filter warning light on        		 When the switch is not connected to the combination meter assembly via direct line, the value of the Data List item will not change.
        Coolant Temperature Engine coolant temperature Min.: 0.0°C, Max.: 127.1°C or Unset 75 to 100°C: After warming up engine -
        Integrated value for Maintenance Maintenance required reminder value Min.: 0 miles, Max.: 25401 miles or Unset Driving distance after performing maintenance required reminder reset procedure displayed -
        Parking Brake Switch Parking brake switch OFF or ON OFF: Parking brake released
        ON: Parking brake applied        		 When the switch is not connected to the combination meter assembly via direct line, the value of the Data List item will not change.
        Brake Fluid Amount Brake fluid level OK or Low OK: Brake fluid level normal
        Low: Brake fluid level abnormal        		 When the switch is not connected to the combination meter assembly via direct line, the value of the Data List item will not change.
        Brake Negative Pressure Brake vacuum pressure OK or NG OK: Brake vacuum pressure normal
        NG: Brake vacuum pressure abnormal        		 When the switch is not connected to the combination meter assembly via direct line, the value of the Data List item will not change.
        TPMS System Existence of tire pressure warning system Without or With Without: w/o Tire Pressure Warning System
        With: w/ Tire Pressure Warning System        		 -
        VGRS System Existence of variable gear ratio steering system Without or With Without: w/o Variable Gear Ratio Steering System
        With: w/ Variable Gear Ratio Steering System        		 -
        VSC System Existence of electronically controlled brake system Without or With Without: w/o Electronically Controlled Brake System
        With: w/ Electronically Controlled Brake System        		 -
        DRS System Existence of dynamic rear steering system Without or With Without: w/o Dynamic Rear Steering System
        With: w/ Dynamic Rear Steering System        		 -
        Pop Up Hood System Existence of pop up hood Without or With Without: w/o Pop up Hood
        With: w/ Pop up Hood        		 -
        AVS System Existence of adaptive variable suspension system Without or With Without: w/o Adaptive Variable Suspension System
        With: w/ Adaptive Variable Suspension System        		 -
        LDA System Existence of lane control system Without or With Without: w/o Lane Control System
        With: w/ Lane Control System        		 -
        PCS System Existence of pre-collision system Without or With Without: w/o Pre-collision System
        With: w/ Pre-collision System        		 -
        ICS System Existence of parking support brake system Without or With Without: w/o Parking Support Brake System
        With: w/ Parking Support Brake System        		 -
        Radar Cruise System Existence of dynamic radar cruise control system Without or With Without: w/o Dynamic Radar Cruise Control System
        With: w/ Dynamic Radar Cruise Control System        		 -
        Intuitive P/A System Existence of intuitive parking assist system Without or With Without: w/o Intuitive Parking Assist System
        With: w/ Intuitive Parking Assist System        		 -
        Road Sign Assist System Existence of road sign assist system Without or With Without: w/o Road Sign Assist System
        With: w/ Road Sign Assist System        		 -
        HV/EV System Indicator Hybrid system indicator value Min.: -101%, Max.: 511% or Unset Current hybrid system indicator value "Unset" is displayed when the vehicle is stopped and the ignition switch is ON (READY).
        ODO Display Time After IG OFF Adjust Setting of the trip result display time after the ignition switch is turned off 30s, 60s, 600s or OFF - If it is possible to customize the setting, the current setting is displayed.
        Tail Remind Buzzer Function Setting of tail remind buzzer function OFF or ON - If it is possible to customize the setting, the current setting is displayed.
        Flasher Sound Volume Adjust Setting of flasher sound volume adjustment Large, Medium or Small - If it is possible to customize the setting, the current setting is displayed.
        Reverse Buzzer Setting Setting of reverse buzzer Continual or Single - If it is possible to customize the setting, the current setting is displayed.
        Brake Pad Sensor Signal Brake pad wear signal OFF or ON OFF: Brake pad replacement not necessary
        ON: Brake pad replacement necessary        		 When the switch is not connected to the combination meter assembly via direct line, the value of the Data List item will not change.
        Sub Fuel Sender No. 2 fuel sender gauge assembly Without or With Without: w/o No. 2 Fuel Sender Gauge Assembly
        With: w/ No. 2 Fuel Sender Gauge Assembly        		 -
        Steering Heater Indicator Heated steering wheel indicator light signal OFF or ON OFF: Heated steering wheel indicator light off
        ON: Heated steering wheel indicator light on        		 When the switch is not connected to the combination meter assembly via direct line, the value of the Data List item will not change.
      2. Brake/EPB

        Chassis > Brake/EPB > Data List 

        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        Vehicle Speed Vehicle speed Min.: 0.0 km/h (0.0 mph)
        Max.: 6553.5 km/h (4072 mph)        		 Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
      3. Engine

        Powertrain > Engine > Data List 

        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        Engine Speed Engine speed Min.: 0 rpm, Max.: 16383 rpm for HV Model 
        1. 1050 to 1150 rpm: Idling (shift lever in P, engine warmed up, inspection mode [maintenance mode] and not charge control)

        for Gasoline Model 

        1. 650 to 750 rpm: Idling (shift lever in N, engine warmed up and A/C off)
        		 When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
      4. Main Body

        Body Electrical > Main Body > Data List 

        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        Suggestion Service Function Setting of Suggestion Service OFF, Only Parked or ON - If it is possible to customize the setting, the current setting is displayed.
  2. ACTIVE TEST 

    HINT: 

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the GTS to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the GTS on.
    4. Enter the following menus: Body Electrical / Combination Meter / Active Test.
    5. Perform the Active Test according the display on the GTS.
      NOTE:

      Depending on the vehicle specifications, some of the Active Test items in the following table will not be displayed on the GTS.

      Body Electrical > Combination Meter > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      Speedometer Operation (0km/h, 0MPH) Speedometer
      (0 km/h, 0 mph)      		 ON When this Active Test is performed, an operation signal is sent directly to the combination meter assembly to operate the speedometer.
      Speedometer Operation (40km/h, 40MPH) Speedometer
      (40 km/h, 40 mph)      		 ON
      • When this Active Test is performed, an operation signal is sent directly to the combination meter assembly to operate the speedometer.
      • The value displayed on the speedometer may deviate.*
      Speedometer Operation (80km/h, 80MPH) Speedometer
      (80 km/h, 80 mph)      		 ON
      • When this Active Test is performed, an operation signal is sent directly to the combination meter assembly to operate the speedometer.
      • The value displayed on the speedometer may deviate.*
      Speedometer Operation (120km/h, 120MPH) Speedometer
      (120 km/h, 120 mph)      		 ON
      • When this Active Test is performed, an operation signal is sent directly to the combination meter assembly to operate the speedometer.
      • The value displayed on the speedometer may deviate.*
      Speedometer Operation (160km/h, 160MPH) Speedometer
      (160 km/h, 160 mph)      		 ON
      • When this Active Test is performed, an operation signal is sent directly to the combination meter assembly to operate the speedometer.
      • The value displayed on the speedometer may deviate.*
      Speedometer Operation (200km/h, 200MPH) Speedometer
      (200 km/h, 200 mph)      		 ON
      • When this Active Test is performed, an operation signal is sent directly to the combination meter assembly to operate the speedometer.
      • The value displayed on the speedometer may deviate.*
      Speedometer Operation (240km/h, 240MPH) Speedometer
      (240 km/h, 240 mph)      		 ON When this Active Test is performed, an operation signal is sent directly to the combination meter assembly to operate the speedometer.
      Speedometer Operation (280km/h, 280MPH) Speedometer
      (280 km/h, 280 mph)      		 ON When this Active Test is performed, an operation signal is sent directly to the combination meter assembly to operate the speedometer.
      Speedometer Operation (320km/h, 320MPH) Speedometer
      (320 km/h, 320 mph)      		 ON When this Active Test is performed, an operation signal is sent directly to the combination meter assembly to operate the speedometer.
      Speedometer Operation (360km/h, 360MPH) Speedometer
      (360 km/h, 360 mph)      		 ON When this Active Test is performed, an operation signal is sent directly to the combination meter assembly to operate the speedometer.
      Speedometer Operation (400km/h, 400MPH) Speedometer
      (400 km/h, 400 mph)      		 ON When this Active Test is performed, an operation signal is sent directly to the combination meter assembly to operate the speedometer.
      TachoMeter Operation (0rpm) Tachometer
      (0 rpm)      		 ON -
      TachoMeter Operation (1000rpm) Tachometer
      (1000 rpm)      		 ON -
      TachoMeter Operation (2000rpm) Tachometer
      (2000 rpm)      		 ON -
      TachoMeter Operation (3000rpm) Tachometer
      (3000 rpm)      		 ON -
      TachoMeter Operation (4000rpm) Tachometer
      (4000 rpm)      		 ON -
      TachoMeter Operation (5000rpm) Tachometer
      (5000 rpm)      		 ON -
      TachoMeter Operation (6000rpm) Tachometer
      (6000 rpm)      		 ON -
      TachoMeter Operation (7000rpm) Tachometer
      (7000 rpm)      		 ON -
      TachoMeter Operation (8000rpm) Tachometer
      (8000 rpm)      		 ON -
      TachoMeter Operation (9000rpm) Tachometer
      (9000 rpm)      		 ON -
      TachoMeter Operation (10000rpm) Tachometer
      (10000 rpm)      		 ON -
      Fuel Gauge Operation (Sender E) Fuel receiver gauge
      (Fuel sender gauge lower limit)      		 ON See [Display 1]
      Fuel Gauge Operation (Empty) Fuel receiver gauge
      (Fuel receiver gauge indicates E)      		 ON See [Display 1]
      Fuel Gauge Operation (Warning) Fuel receiver gauge
      (Position at which fuel level warning light turns on/off)      		 ON See [Display 1]
      Fuel Gauge Operation (1/4) Fuel receiver gauge
      (Fuel receiver gauge indicates 1/4)      		 ON See [Display 1]
      Fuel Gauge Operation (1/2) Fuel receiver gauge
      (Fuel receiver gauge indicates 1/2)      		 ON See [Display 1]
      Fuel Gauge Operation (3/4) Fuel receiver gauge
      (Fuel receiver gauge indicates 3/4)      		 ON See [Display 1]
      Fuel Gauge Operation (Full) Fuel receiver gauge
      (Fuel receiver gauge indicates F)      		 ON See [Display 1]
      Fuel Gauge Operation (Sender F) Fuel receiver gauge
      (Fuel sender gauge upper limit)      		 ON See [Display 1]
      Sub Fuel Gauge Operation (Sender E) Sub fuel receiver gauge
      (Fuel sender gauge lower limit for sub fuel receiver gauge)      		 ON -
      Sub Fuel Gauge Operation (Empty) Sub fuel receiver gauge
      (Sub fuel receiver gauge indicates E)      		 ON -
      Sub Fuel Gauge Operation (1/4) Sub fuel receiver gauge
      (Sub fuel receiver gauge indicates 1/4)      		 ON -
      Sub Fuel Gauge Operation (1/2) Sub fuel receiver gauge
      (Sub fuel receiver gauge indicates 1/2)      		 ON -
      Sub Fuel Gauge Operation (3/4) Sub fuel receiver gauge
      (Sub fuel receiver gauge indicates 3/4)      		 ON -
      Sub Fuel Gauge Operation (Full) Sub fuel receiver gauge
      (Sub fuel receiver gauge indicates F)      		 ON -
      Sub Fuel Gauge Operation (Sender F) Sub fuel receiver gauge
      (Fuel sender gauge upper limit for sub fuel receiver gauge)      		 ON -
      Water Temperature Meter Operation (50C, 122F) Engine coolant temperature receiver gauge
      (50°C, 122°F)      		 ON See [Display 2]
      Water Temperature Meter Operation (60C, 140F) Engine coolant temperature receiver gauge
      (60°C, 140°F)      		 ON See [Display 2]
      Water Temperature Meter Operation (70C, 158F) Engine coolant temperature receiver gauge
      (70°C, 158°F)      		 ON See [Display 2]
      Water Temperature Meter Operation (80C, 176F) Engine coolant temperature receiver gauge
      (80°C, 176°F)      		 ON See [Display 2]
      Water Temperature Meter Operation (Middle) Engine coolant temperature receiver gauge
      (Middle)      		 ON See [Display 2]
      Water Temperature Meter Operation (110C, 230F) Engine coolant temperature receiver gauge
      (110°C, 230°F)      		 ON See [Display 2]
      Water Temperature Meter Operation (120C, 248F) Engine coolant temperature receiver gauge
      (120°C, 248°F)      		 ON See [Display 2]
      Water Temperature Meter Operation (127C, 260F) Engine coolant temperature receiver gauge
      (127°C, 260°F)      		 ON See [Display 2]
      Volt Meter Operation (0V) Voltmeter
      (0 V)      		 ON -
      Volt Meter Operation (3V) Voltmeter
      (3 V)      		 ON -
      Volt Meter Operation (6V) Voltmeter
      (6 V)      		 ON -
      Volt Meter Operation (9V) Voltmeter
      (9 V)      		 ON -
      Volt Meter Operation (12V) Voltmeter
      (12 V)      		 ON -
      Volt Meter Operation (15V) Voltmeter
      (15 V)      		 ON -
      Volt Meter Operation (18V) Voltmeter
      (18 V)      		 ON -
      Oil Pressure Meter Operation (LOW) Engine oil pressure receiver gauge
      (Engine oil pressure receiver gauge indicates Low)      		 ON -
      Oil Pressure Meter Operation (1/4) Engine oil pressure receiver gauge
      (Engine oil pressure receiver gauge indicates 1/4)      		 ON -
      Oil Pressure Meter Operation (1/2) Engine oil pressure receiver gauge
      (Engine oil pressure receiver gauge indicates 1/2)      		 ON -
      Oil Pressure Meter Operation (3/4) Engine oil pressure receiver gauge
      (Engine oil pressure receiver gauge indicates 3/4)      		 ON -
      Oil Pressure Meter Operation (HIGH) Engine oil pressure receiver gauge
      (Engine oil pressure receiver gauge indicates High)      		 ON -
      HV/EV System Indicator (MIN) Hybrid system indicator value
      (Charge area)      		 ON See [Display 3]
      HV/EV System Indicator (-50%) Hybrid system indicator value
      (Charge area)      		 ON See [Display 3]
      HV/EV System Indicator (0%) Hybrid system indicator value
      (Charge area)      		 ON See [Display 3]
      HV/EV System Indicator (100%) Hybrid system indicator value
      (Eco area)      		 ON See [Display 3]
      HV/EV System Indicator (200%) Hybrid system indicator value
      (Power area)      		 ON See [Display 3]
      HV/EV System Indicator (300%) Hybrid system indicator value
      (Power area)      		 ON See [Display 3]
      HV/EV System Indicator (400%) Hybrid system indicator value
      (Power area)      		 ON See [Display 3]
      HV/EV System Indicator (MAX) Hybrid system indicator value
      (Power area)      		 ON See [Display 3]
      SOC Gauge (MIN) Hybrid battery status gauge
      (Hybrid battery status gauge indicates Min.)      		 ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      SOC Gauge (1/4) Hybrid battery status gauge
      (Hybrid battery status gauge indicates 1/4)      		 ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      SOC Gauge (1/2) Hybrid battery status gauge
      (Hybrid battery status gauge indicates 1/2)      		 ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      SOC Gauge (3/4) Hybrid battery status gauge
      (Hybrid battery status gauge indicates 3/4)      		 ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      SOC Gauge (MAX) Hybrid battery status gauge
      (Hybrid battery status gauge indicates Max.)      		 ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      Fuel Gauge Operation for CNG (Sender E) Fuel receiver gauge (for CNG)
      (Fuel sender gauge (for CNG) lower limit)      		 ON -
      Fuel Gauge Operation for CNG (Empty) Fuel receiver gauge (for CNG)
      (Fuel receiver gauge (for CNG) indicates E)      		 ON -
      Fuel Gauge Operation for CNG (Warning) Fuel receiver gauge (for CNG)
      (Position at which fuel level warning light (for CNG) turns on/off)      		 ON -
      Fuel Gauge Operation for CNG (1/4) Fuel receiver gauge (for CNG)
      (Fuel receiver gauge (for CNG) indicates 1/4)      		 ON -
      Fuel Gauge Operation for CNG (1/2) Fuel receiver gauge (for CNG)
      (Fuel receiver gauge (for CNG) indicates 1/2)      		 ON -
      Fuel Gauge Operation for CNG (3/4) Fuel receiver gauge (for CNG)
      (Fuel receiver gauge (for CNG) indicates 3/4)      		 ON -
      Fuel Gauge Operation for CNG (Full) Fuel receiver gauge (for CNG)
      (Fuel receiver gauge (for CNG) indicates F)      		 ON -
      Fuel Gauge Operation for CNG (Sender F) Fuel receiver gauge (for CNG)
      (Fuel sender gauge (for CNG) upper limit)      		 ON -
      Buzzer Operation (800Hz, Vol L, W/ Damping) Combination meter buzzer
      • Frequency: 800Hz
      • Volume: Large
      • Fading tone
      		 ON -
      Buzzer Operation (800Hz, Vol L, W/O Damping) Combination meter buzzer
      • Frequency: 800Hz
      • Volume: Large
      • Continuous tone
      		 ON -
      Buzzer Operation (800Hz, Vol S, W/ Damping) Combination meter buzzer
      • Frequency: 800Hz
      • Volume: Small
      • Fading tone
      		 ON -
      Buzzer Operation (800Hz, Vol S, W/O Damping) Combination meter buzzer
      • Frequency: 800Hz
      • Volume: Small
      • Continuous tone
      		 ON -
      Buzzer Operation (1.6kHz, Vol S, W/O Damping) Combination meter buzzer
      • Frequency: 1.6kHz
      • Volume: Small
      • Continuous tone
      		 ON -
      Buzzer Operation (2.0kHz, Vol S, W/O Damping) Combination meter buzzer
      • Frequency: 2.0kHz
      • Volume: Small
      • Continuous tone
      		 ON -
      Buzzer Operation (2.4kHz, Vol L, W/O Damping) Combination meter buzzer
      • Frequency: 2.4kHz
      • Volume: Large
      • Continuous tone
      		 ON -
      Multi Display All (White) Multi-information display
      (White display)      		 ON -
      Multi Display Default Screen Multi-information display
      (Default screen)      		 ON -
      Meter Display (All) Segment display
      (All display)      		 ON -
      Meter Display (0) Segment display
      (0 display)      		 ON -
      Meter Display (1) Segment display
      (1 display)      		 ON -
      Meter Display (2) Segment display
      (2 display)      		 ON -
      Meter Display (3) Segment display
      (3 display)      		 ON -
      Meter Display (4) Segment display
      (4 display)      		 ON -
      Meter Display (5) Segment display
      (5 display)      		 ON -
      Meter Display (6) Segment display
      (6 display)      		 ON -
      Meter Display (7) Segment display
      (7 display)      		 ON -
      Meter Display (8) Segment display
      (8 display)      		 ON -
      Meter Display (9) Segment display
      (9 display)      		 ON -
      Fuel Gauge Indicator Fuel level warning light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      High Beam Indicator High beam indicator light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      Headlamp Indicator Head indicator light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      Taillamp Indicator Tail indicator light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      Front Fog Lamp Indicator Front fog indicator light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      Rear Fog Lamp Indicator Rear fog indicator light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      Automatic High Beam Indicator (Green) Automatic high beam/adaptive high beam indicator light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      Left Turn Signal Indicator LH turn indicator light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      Right Turn Signal Indicator RH turn indicator light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      Driver Side Seat Belt Warning Driver or front passenger seat belt warning light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      Passenger Side Seat Belt Warning Front passenger seat belt warning light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      Rear Seat Belt Warning Rear seat belt warning light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      Airbag Warning SRS warning light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      ECONO Indicator Eco driving indicator light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      Check Engine Warning MIL (Check engine warning light) OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      Brake Warning Brake warning light / red (malfunction) OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      Park Warning Parking brake indicator light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      ABS Warning ABS warning light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      ECB Warning Brake warning light / yellow (minor malfunction) OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      Slip Warning Slip indicator light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      VSC OFF Indicator VSC OFF indicator light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      Brake Hold Indicator Brake hold standby indicator light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      Hold Indicator Brake hold operated indicator light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      Downhill Assist Control Indicator Downhill assist control indicator light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      Tire Pressure Warning System Indicator Tire pressure warning light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      EPS Warning EPS warning light
      (Red)      		 OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      PPS Warning EPS warning light
      (Amber)      		 OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      PCS OFF Warning PCS warning light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      ICS OFF Warning PKSB OFF indicator light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      Stop and Start ON Indicator Stop and start indicator light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      Stop and Start OFF Indicator Stop and start off indicator light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      INTUITIVE P/A LCD OFF Indicator Clearance sonar off indicator light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      Ready Indicator Ready indicator light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      EV Mode Indicator EV MODE indicator light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      EV Drive Indicator EV driving indicator light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      Auxiliary Battery Warning Charge warning light OFF or ON For models that display the measurement item on the multi-information display, the Active Test may not operate or may provide an invalid result.
      Speed Signal Input (0) Vehicle speed test signal input ON When this Active Test is performed, an actual vehicle speed signal is sent via CAN communication to the combination meter assembly to operate the speedometer. The seat belt warning buzzer, etc. may operate when performing this Active Test.
      Speed Signal Input (40) Vehicle speed test signal input ON
      • When this Active Test is performed, an actual vehicle speed signal is sent via CAN communication to the combination meter assembly to operate the speedometer. The seat belt warning buzzer, etc. may operate when performing this Active Test.
      • The value displayed on the speedometer may deviate.*
      Speed Signal Input (80) Vehicle speed test signal input ON
      • When this Active Test is performed, an actual vehicle speed signal is sent via CAN communication to the combination meter assembly to operate the speedometer. The seat belt warning buzzer, etc. may operate when performing this Active Test.
      • The value displayed on the speedometer may deviate.*
      Speed Signal Input (120) Vehicle speed test signal input ON
      • When this Active Test is performed, an actual vehicle speed signal is sent via CAN communication to the combination meter assembly to operate the speedometer. The seat belt warning buzzer, etc. may operate when performing this Active Test.
      • The value displayed on the speedometer may deviate.*
      Speed Signal Input (160) Vehicle speed test signal input ON
      • When this Active Test is performed, an actual vehicle speed signal is sent via CAN communication to the combination meter assembly to operate the speedometer. The seat belt warning buzzer, etc. may operate when performing this Active Test.
      • The value displayed on the speedometer may deviate.*
      Speed Signal Input (200) Vehicle speed test signal input ON
      • When this Active Test is performed, an actual vehicle speed signal is sent via CAN communication to the combination meter assembly to operate the speedometer. The seat belt warning buzzer, etc. may operate when performing this Active Test.
      • The value displayed on the speedometer may deviate.*
      Speed Signal Input (240) Vehicle speed test signal input ON When this Active Test is performed, an actual vehicle speed signal is sent via CAN communication to the combination meter assembly to operate the speedometer. The seat belt warning buzzer, etc. may operate when performing this Active Test.
      Speed Signal Input (280) Vehicle speed test signal input ON When this Active Test is performed, an actual vehicle speed signal is sent via CAN communication to the combination meter assembly to operate the speedometer. The seat belt warning buzzer, etc. may operate when performing this Active Test.
      Speed Signal Input (320) Vehicle speed test signal input ON When this Active Test is performed, an actual vehicle speed signal is sent via CAN communication to the combination meter assembly to operate the speedometer. The seat belt warning buzzer, etc. may operate when performing this Active Test.
      Speed Signal Input (360) Vehicle speed test signal input ON When this Active Test is performed, an actual vehicle speed signal is sent via CAN communication to the combination meter assembly to operate the speedometer. The seat belt warning buzzer, etc. may operate when performing this Active Test.
      Speed Signal Input (400) Vehicle speed test signal input ON When this Active Test is performed, an actual vehicle speed signal is sent via CAN communication to the combination meter assembly to operate the speedometer. The seat belt warning buzzer, etc. may operate when performing this Active Test.
      ODO/TRIP Change Switch ODO/TRIP switch OFF or ON -
      Trip Reset Switch Trip reset switch OFF or ON -
      Multi Display Select Switch DISP switch OFF or ON -
      Meter Day Mode Switch Tail cancel switch OFF or ON -
      Light Control Switch (UP) Light control rheostat up switch OFF or ON -
      Light Control Switch (DOWN) Light control rheostat down switch OFF or ON -
      Light Control Switch (Single) Light control rheostat switch OFF or ON -
      Timer Switch (H) Clock switch (H) OFF or ON -
      Timer Switch (M) Clock switch (M) OFF or ON -
      Timer Switch (00) Clock switch (00) OFF or ON -
      Timer Switch (Single) Clock switch OFF or ON -
      Multi Switch (Up) Up switch on steering pad switch OFF or ON -
      Multi Switch (Down) Down switch on steering pad switch OFF or ON -
      Multi Switch (Left) Left switch on steering pad switch OFF or ON -
      Multi Switch (Right) Right switch on steering pad switch OFF or ON -
      Multi Switch (Enter) OK switch on steering pad switch OFF or ON -
      Multi Switch (Back) Back switch on steering pad switch OFF or ON -
      Multi Switch (Top) Top switch on steering pad switch OFF or ON -
      1. *: For the tolerance of each Speed Signal Input Active Test, refer to On-vehicle Inspection.

        Refer to ON-VEHICLE INSPECTION [12/2019 - ]

      1. [Display 1]: Fuel Gauge Operation
        GTY848424Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Fuel Receiver Gauge

        HINT: 

        Refer to the following table for the specified fuel receiver gauge position for each selected value:

        Tester Display Fuel Receiver Gauge Indication
        Fuel Gauge Operation
        (Sender E)        		 Approximately 1 is indicated
        Fuel Gauge Operation
        (Empty)        		 Approximately 2 is indicated
        Fuel Gauge Operation
        (Warning)        		 Approximately 3 is indicated
        Fuel Gauge Operation
        (1/4)        		 Approximately 4 is indicated
        Fuel Gauge Operation
        (1/2)        		 Approximately 5 is indicated
        Fuel Gauge Operation
        (3/4)        		 Approximately 6 is indicated
        Fuel Gauge Operation
        (Full)        		 Approximately 7 is indicated
        Fuel Gauge Operation
        (Sender F)        		 Approximately 8 is indicated
      2. [Display 2]: Water Temperature Meter Operation
        GTY927346Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Engine Coolant Temperature Receiver Gauge

        HINT: 

        Refer to the following table for the specified engine coolant temperature receiver gauge position for each selected value:

        Tester Display Engine Coolant Temperature Receiver Gauge Indication
        Water Temperature Meter Operation
        (50C, 122F)        		 Between 2 and 3 is indicated*1
        Between 1 and 2 is indicated*2
        Water Temperature Meter Operation
        (60C, 140F)        		 Between 3 and 4 is indicated*1
        Between 2 and 3 is indicated*2
        Water Temperature Meter Operation
        (70C, 158F)        		 Between 3 and 4 is indicated
        Water Temperature Meter Operation
        (80C, 176F)        		 Between 3 and 4 is indicated
        Water Temperature Meter Operation
        (Middle)        		 Between 3 and 4 is indicated
        Water Temperature Meter Operation
        (110C, 230F)        		 Between 4 and 5 is indicated
        Water Temperature Meter Operation
        (120C, 248F)        		 Approximately 6 is indicated
        Water Temperature Meter Operation
        (127C, 260F)        		 Approximately 7 is indicated
        1. *1: for HV Model
        2. *2: for Gasoline Model
      3. [Display 3]: HV/EV System Indicator
        GTY910497Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Hybrid System Indicator

        HINT: 

        Refer to the following table for the specified hybrid system indicator position for each selected value:

        Tester Display Hybrid System Indicator Indication
        HV/EV System Indicator
        (MIN)        		 Approximately 1 is indicated
        HV/EV System Indicator
        (-50%)        		 Approximately 2 is indicated
        HV/EV System Indicator
        (0%)        		 Approximately 3 is indicated
        HV/EV System Indicator
        (100%)        		 Approximately 4 is indicated
        HV/EV System Indicator
        (200%)        		 Approximately 5 is indicated
        HV/EV System Indicator
        (300%)        		 Approximately 6 is indicated
        HV/EV System Indicator
        (400%)        		 Approximately 7 is indicated
        HV/EV System Indicator
        (MAX)        		 Approximately 8 is indicated
Diesel-Data.com