DSD Information System
Home >> Toyota >> 2021 >> Highlander LE, 4WD >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Communication Devices >> Can Communication System (Except HV) - Circuit Tests (2 Of 8) >> CAN COMMUNICATION SYSTEM (for Gasoline Model) >> Headup Display Communication Stop Mode [11/2023 - ] >> Procedure

Headup Display Communication Stop Mode [11/2023 - ]: Procedure

  1. CHECK FOR OPEN IN CAN BUS LINES (METER MIRROR SUB-ASSEMBLY BRANCH LINE) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the H31 meter mirror sub-assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      H31-12 (MPX1) - H31-13 (MPX2) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      GTY1178225Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Meter Mirror Sub-assembly)

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (METER MIRROR SUB-ASSEMBLY) 

    Result: 

    OK 

    See step  2

  2. CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      H31-4 (ES) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
      GTY1178226Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Meter Mirror Sub-assembly)

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT) 

    Result: 

    OK 

    See step  3

  3. CHECK VEHICLE TYPE 
    1. Check vehicle type.

      Result

      Result Proceed to
      w/ Stop and Start System A
      w/o Stop and Start System B

    Result: 

    B 

    See step  5

    Result: 

    A 

    See step  4

  4. CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT) 
    1. Reconnect the cable to the negative (-) battery terminal.
    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      H31-1 (IG) - Body ground Ignition switch ON 10.5 to 16 V
      H31-2 (B) - Body ground Always 10.5 to 16 V
      GTY1177762Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Meter Mirror Sub-assembly)

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE METER MIRROR SUB-ASSEMBLY 

    Refer to REMOVAL [11/2023 - ]

    Result: 

    NG 

    GO TO STOP AND START SYSTEM (FOR BACKUP BOOST CONVERTER CIRCUIT) 

    Refer to Backup Boost Converter Circuit [11/2023 - ]

  5. CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT) 
    1. Reconnect the cable to the negative (-) battery terminal.
    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      H31-1 (IG) - Body ground Ignition switch ON 11 to 14 V
      H31-2 (B) - Body ground Always 11 to 14 V
      GTY1177762Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Meter Mirror Sub-assembly)

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE METER MIRROR SUB-ASSEMBLY 

    Refer to REMOVAL [11/2023 - ]

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT) 

Diesel-Data.com